Harnais chaudière à gaz: sol, mur, simple et double circuit
5 (100%) voix : 1Arrangement chauffage au gaz- une étape très importante et responsable. Une atmosphère confortable et chaleureuse dans la maison dépend de la qualité des matériaux sélectionnés, ainsi que de la technologie utilisée. travaux d'installation. Bien entendu, un schéma de tuyauterie correct pour une chaudière à gaz protégera le système des surcharges et garantira également une répartition uniforme de la chaleur dans toute la pièce.
Tuyauterie d'une chaudière à gaz
Tuyauterie de chaudière à gaz et sa fonction
La tuyauterie fait référence aux tuyaux et aux mécanismes utilisés pour fournir du liquide de refroidissement de la chaudière aux radiateurs. C'est presque tout système de chauffage, hors piles.
Le système comprend un grand nombre de composants, mais la version la plus simple du harnais peut être installée par un non-professionnel. Mais si un schéma est nécessaire, dans ce cas, il est préférable de demander l'aide de spécialistes.
Lors du choix d'un schéma de tuyauterie, dans chaque cas spécifique, il est nécessaire de prendre en compte le type de chaudière, les caractéristiques de construction et le type de système de chauffage.
Toute unité à gaz est dangereuse. Si vous faites des erreurs lors du processus de connexion, le résultat peut être non seulement des problèmes de chauffage de votre maison, mais également des explosions et des destructions. C'est pourquoi il est très important de respecter strictement les normes et exigences de sécurité. Lorsque vous installez une chaudière à gaz pour chauffer une maison privée, vous devez vous fier aux exigences du SNiP.
Il est nécessaire de bien planifier le système de chauffage, de décider de l'emplacement de l'équipement et des caractéristiques de pose des canalisations.
La tuyauterie de la chaudière remplit un certain nombre de fonctions très importantes :
- Contrôle la pression. Si toutes les conditions de la tuyauterie sont remplies et qu'elle est réalisée correctement, la dilatation thermique est alors compensée. Cela signifie que la pression dans le système de chauffage n’augmentera pas trop haut.
- La fonction suivante est l'évacuation de l'air. En raison des bulles d'air, des embouteillages apparaissent, ce qui affecte négativement le chauffage de l'eau. Dans de telles situations, les radiateurs chauffent de manière inégale, mais la consommation de ressources reste la même. Il est nécessaire de réaliser une tuyauterie de chaudière de haute qualité afin d'éviter de tels moments désagréables.
- Prévention des blocages dans le système. Si vous faites des erreurs lors du processus de tuyauterie de la chaudière, il existe une forte probabilité que du tartre apparaisse dans les radiateurs et les tuyaux. De petits débris présents dans le liquide de refroidissement polluent le système, ce qui entraîne une consommation excessive de carburant, ce qui augmente le coût du chauffage, tandis que sa qualité diminue.
- D'autres circuits peuvent être connectés. Vous pouvez en outre installer un chauffage au sol et une chaudière à accumulation.
Dans l'ensemble, l'approvisionnement en chaleur dépend directement de la précision du respect de la technologie de raccordement de la chaudière aux canalisations et autres éléments importants, il est donc très important de bien réfléchir au schéma de tuyauterie de la chaudière à gaz et de le produire aussi efficacement que possible.
Composants de tuyauterie de chaudière
La tuyauterie de la chaudière peut inclure divers éléments:
- Vase d'expansion à membrane. Sa tâche principale est de compenser l'augmentation du volume d'eau ou d'antigel dans un circuit de chauffage fermé lors du chauffage. Le réservoir est divisé en deux parties au moyen d'un élastique membrane, et une partie de son volume est remplie d'air. Lorsque le volume de liquide de refroidissement augmente, le gaz est comprimé et la pression dans le circuit augmente considérablement.
- Soupape de sécurité. La fonction principale de cet élément est d’évacuer l’excès de liquide de refroidissement lors d’une augmentation dangereuse de la pression dans le circuit, protégeant ainsi le système d’une éventuelle rupture des tuyaux et des batteries. L'eau est évacuée à l'aide d'un tuyau de drainage dans les égouts. Si la vanne fonctionne fréquemment, cela signifie que le volume du vase d'expansion est trop petit.
- Bouche d'aération.
Tuyauterie d'une chaudière à gaz à circuit unique
Un système de tuyauterie simple pour une chaudière à gaz avec un circuit est élaboré en fonction des caractéristiques et des exigences unité de chauffage. Monté côté alimentation clapet anti-retour et un robinet à tournant sphérique. Une pompe est montée sur les tuyaux de retour et de refoulement, assurant la circulation du liquide et une répartition uniforme du liquide de refroidissement dans les pièces.
Exemple de tuyauterie de chaudière pour une maison privée
Un filtre à mailles est installé devant lui, qui est placé avec le côté puisard vers le bas. Avant que le liquide ne pénètre dans la chaudière, les experts recommandent d'installer un filtre fin. Un vase d'expansion fermé doit être situé plus près de la chaudière. Il contient une membrane qui permet de relâcher la pression lorsque dilatation thermique liquides. Depuis la pompe, le liquide de refroidissement circule le long du circuit jusqu'aux radiateurs.
Une solution plus moderne consiste à découpler via un collecteur - un collecteur d'eau spécial, à partir duquel le liquide est distribué à travers plusieurs circuits. Le collecteur est situé dans une armoire spéciale à partir de laquelle le liquide de refroidissement est distribué par des canalisations.
Le circuit de tuyauterie de la chaudière à gaz comprend une soupape de sécurité. Lorsque le liquide de refroidissement bout, en raison d'une surchauffe, le vase d'expansion peut tout simplement ne pas résister aux chutes de pression et, par conséquent, un dysfonctionnement se produira, ce qui aura les conséquences suivantes :
- ruptures de pipelines et fuites de connexion ;
- destruction de canalisations et raccords ;
- explosion du réservoir de la chaudière.
La soupape de sécurité est montée le plus près possible de la chaudière, car la pression y augmente. Certains appareils ont groupes de sécurité, qui comprend une soupape de décharge, un purgeur d'air automatique et un manomètre.
Les appareils sont installés dans la chemise d'eau de la chaudière, mais peuvent également être montés sur des canalisations. Sur les unités fonctionnant au gaz et à l'électricité, ces appareils peuvent être remplacés par d'autres.
Il existe un grand nombre de manières de connecter les éléments décrits à la chaudière, elles sont classées en fonction du type de circulation du liquide de refroidissement dans le système : naturelle ou forcée.
Circulation naturelle
Le principe de fonctionnement est basé sur la réduction de la densité de l'eau lorsqu'elle est chauffée. liquide chaud le froid le pousse vers le haut, où il circule à travers les appareils de chauffage, dégageant une certaine quantité d'énergie thermique et retournant à la chaudière pour se chauffer.
L'installation des tuyaux de sortie et d'entrée s'effectue avec une inclinaison d'au moins 3°. Cela est nécessaire pour qu'une circulation naturelle se produise et que moins d'air s'accumule dans le système.
En circulation naturelle, la tuyauterie de la chaudière est réalisée de telle manière que les radiateurs se trouvent au-dessus de la canalisation d'alimentation.
La ligne de retour passe par le haut également avec une pente. Si l'installation est effectuée correctement et que les diamètres des tuyaux sont sélectionnés conformément aux exigences, la circulation naturelle est alors presque identique en puissance à la circulation forcée.
Avantages de cette méthode :
- le système est simple ;
- l'installation n'est pas difficile ;
- pendant le fonctionnement, les unités ne font pratiquement aucun bruit ;
- caractérisé par une longue durée de vie.
Le système est destiné à fournir de la chaleur à de petites pièces dont la superficie n'excède pas 100 m². Comme inconvénient, on peut noter que la pièce se réchauffe pendant une longue période et qu'il ne sera pas possible de réguler la température dans les pièces individuelles.
Types de tuyauterie de chaudière à gaz
Le circuit gravitaire est généralement utilisé dans les maisons de petite taille, les datchas et en présence d'un seul circuit de chauffage. Il est préférable d'installer des tuyaux dans les murs, car... ils n'auront pas l'air très attrayants à l'intérieur.
Circulation forcée
Cette méthode est considérée comme la plus populaire et la plus répandue, car la pompe pompe intensivement le liquide de refroidissement à travers le système et l'efficacité du chauffage augmente de 30 %.
Comme avantages, on peut noter la possibilité de régler la température et la faible consommation des canalisations lors de l'installation. Le système coûtera plus cher parce que... c'est plus complexe et nécessite grande quantité dispositifs. Les composants installés nécessitent un équilibrage et l'ensemble du système nécessite maintenance régulière. De plus, une source est nécessaire énergie électrique.
Si vous installez un système combiné, il combinera les avantages des deux précédents. Vous pouvez le passer à n'importe quel mode de fonctionnement à l'aide d'un bypass installé avec la pompe. Dans ce cas, le fonctionnement du chauffage dépendra directement de l’apport d’énergie électrique à la maison.
Tuyauterie à faire soi-même d'une chaudière à gaz à double circuit
Voyons maintenant comment raccorder une chaudière à gaz à double circuit.
La principale différence entre un tel appareil de chauffage et une unité à circuit unique est la polyvalence du premier. Il maintient le degré de liquide de refroidissement dans le circuit de chauffage et chauffe également l'eau pendant besoins du ménage. Les unités à circuit unique peuvent également chauffer indirectement l'eau. Le processus de transfert de chaleur est effectué lors du mouvement du liquide de refroidissement à travers l'échangeur de chaleur secondaire.
En outre, une caractéristique distinctive d'une chaudière à double circuit est le transfert direct d'énergie thermique à l'eau. A la consommation eau chaude Le liquide de refroidissement ne chauffe pas. Le fonctionnement simultané de deux circuits est impossible.
Comme le montre la pratique, pour les maisons dotées d'une isolation thermique de haute qualité, le mode de fonctionnement de la chaudière n'a pas d'importance fondamentale. Le circuit de chauffage sera le même pour tout type de chauffage.
Les radiateurs et le liquide de refroidissement assurent un refroidissement à long terme. Ce résultat est dû au choix de radiateurs de grande capacité et de larges diamètres de tuyaux. Un grand volume d'eau chaude peut être obtenu en combinant une conception à circuit unique et une colonne chauffante. Sur les grandes maisons, le fonctionnement de la chaudière n'a aucun effet d'une manière spéciale, les circuits de chauffage seront donc identiques.
Fonctionnalités de connexion
Une chaudière à double circuit n'a pas besoin d'être conçue en conjonction avec un système de circulation naturelle - une fois le chauffage du liquide de refroidissement terminé, son mouvement s'arrêtera court instant. Le réchauffage prend un temps assez long et, par conséquent, la répartition de la chaleur dans le radiateur est inégale. Cependant, de nombreux modèles incluent pompes de circulation.
La version traditionnelle des chaudières tubulaires à deux circuits est la suivante. L'eau chaude monte dans un tuyau d'alimentation qui entoure la maison au-dessus. Ensuite, le liquide de refroidissement circule à travers les colonnes montantes connectées avec des appareils de chauffage qui n'ouvrent pas complètement la colonne montante.
Les radiateurs sont fournis avec un cavalier et un papillon, qui sont responsables des fonctions de régulation thermique. Un robinet d'arrêt est requis sur la deuxième conduite d'alimentation. La purge d'air est montée en partie haute du circuit du vase d'expansion. Par connexion inférieure Le système de refroidissement se déplace dans la direction opposée. L'avantage d'un tel schéma est la possibilité de travailler en mode circulation naturelle.
Tuyauterie d'une chaudière à gaz au sol
Une chaudière au sol fonctionnant au gaz a de petites dimensions, mais pour installer un tel équipement, vous avez besoin de beaucoup d'espace. Cela est dû à la nécessité de placer tous les éléments clés : pompe de circulation, collecteur, coudes, bagues, robinets et instruments.
Raccordement d'une chaudière gaz au sol
La plupart de les modèles muraux sont à circuit unique. Et pour approvisionner la maison en eau chaude, il est nécessaire d'installer une chaudière avec tous les branchements. Le système d'alimentation en eau chaude nécessite une pompe séparée (dans le cas où il n'y a pas d'alimentation en eau centrale), un vase d'expansion et un mitigeur thermostatique.
Il est très important de raccorder le gaz à la chaudière selon les besoins. Pour ce faire, vous devez passer une commande documentation du projet, qui est compilé par des spécialistes. Entrer dans la maison conduite de gaz effectué dans le cas où il existe un dispositif d'arrêt (en cas d'urgence). Le raccordement au gaz est effectué par des services spéciaux qui utilisent des tuyaux, tuyaux et autres équipements spéciaux.
Câblage d'une chaudière à gaz murale
Monter chaudières à gaz Peut être accroché au mur de la cuisine. Ils sont très compacts et peuvent être placés même dans de petites pièces. La tuyauterie murale de la chaudière à gaz est incluse dans le kit et peut même être intégrée à la chaudière.
Comme inconvénient des unités murales, on peut noter une faible puissance. De plus, un tel appareil de chauffage ne peut pas fonctionner sans électricité et la circulation naturelle du liquide de refroidissement n'est pas typique pour eux. En revanche, presque tous les modèles de chaudières de chauffage sont équipés d’électronique et nécessitent de l’électricité. Dans les zones à approvisionnement instable, vous pouvez installer.
De nombreux modèles muraux prévoient de raccorder une chaudière de chauffage à double circuit dont la conception permet d'alimenter la maison en eau chaude.
L'inconvénient d'une unité à double circuit est que le chauffage est éteint pendant la période de consommation d'eau chaude. Ceci est particulièrement visible avec une faible puissance de chaudière. S'il y en a suffisamment, la température du liquide de refroidissement ne baisse que de quelques degrés en quelques heures.
Raccordement d'une chaudière à gaz avec une chaudière à chauffage indirect
Afin de raccorder une chaudière à chauffage indirect à une chaudière à gaz, sa conception prévoit capteur de température, placé dans le réservoir.
Pour que la chaudière fonctionne avec une unité de chauffage équipée d'un circuit d'eau chaude, une soupape de sécurité est utilisée. Avec son aide, le flux de liquide de refroidissement chauffé est réparti entre le circuit de chauffage principal et le circuit auxiliaire d'alimentation en eau chaude.
Le contrôle est effectué en fonction des signaux provenant d'un thermostat intégré au chauffe-eau. Lorsque l'eau de la chaudière refroidit en dessous d'une valeur définie, le thermostat ouvre la vanne qui dirige le flux de liquide de refroidissement de la canalisation de chauffage vers le circuit ECS. Le thermostat ramène la vanne à son état d'origine lorsque la température de l'eau dans le réservoir dépasse la valeur spécifiée. Dans ce cas, le flux de liquide de refroidissement se déplace vers la conduite de chauffage. En saison chaude, le flux est redirigé et le mode de combustion de la chaudière est contrôlé. Lorsque la température de l'eau dans la chaudière diminue, le thermostat utilisant vanne à trois voies« allume » le brûleur principal de l'appareil, et lorsqu'il augmente, l'alimentation en gaz du brûleur s'arrête.
Un tel système constituerait une excellente option pour les chaudières à gaz équipées pompe de circulation et l'automatisation. Dans de telles situations, la vanne peut être contrôlée par la chaudière elle-même, suite à une commande reçue du thermostat du chauffe-eau.
Lors du raccordement d'une chaudière à une chaudière à circuit unique, un circuit à deux pompes de circulation. Cette méthode de connexion peut essentiellement remplacer un circuit avec un capteur à trois voies. Particularité Cette méthode de connexion consiste à séparer les flux de liquide de refroidissement à travers différentes canalisations à l'aide de pompes. Le circuit d'alimentation en eau chaude a également une priorité plus élevée sur le circuit de chauffage, mais ceci est obtenu grâce à un algorithme de commutation clairement structuré.
Activation alternative pompes centrifuges se produit en fonction des signaux du thermostat situé dans le réservoir.
Pour éviter de mélanger les flux de liquide de refroidissement, une soupape de sécurité doit être installée devant chaque pompe.
Attacher une chaudière à gaz avec du polypropylène
La tuyauterie de la chaudière est réalisée à l'aide de la technologie de soudage, ce qui réduit à zéro le risque de fuite, qui se produit le plus souvent en raison d'une installation de raccords de mauvaise qualité.
L'avantage de travailler avec un pipeline en polypropylène sera la possibilité de créer n'importe quel contour. Les débutants peuvent utiliser le schéma le plus simple cerclage.
Peut être appliqué diverses technologies souder du polypropylène et travailler avec des raccords ajustés aux dimensions. Il faut éviter un grand nombre de connexions et ne pas négliger la possibilité de transitions en douceur.
Il est important de respecter une condition : un raccordement rigide au niveau de l'alimentation en gaz de la chaudière.
Les experts conseillent d'utiliser un tuyau métallique et de le connecter à la chaudière à l'aide d'un « américain » ou d'un variateur. Il s’agit d’une exigence clé lorsque l’on travaille avec appareils de chauffage fonctionnant au gaz.
Vous pouvez utiliser un joint en paronite. Cela ne vaut pas la peine d'utiliser du câble, des bandes fumantes et des composants en caoutchouc. Ils peuvent prendre feu et le caoutchouc réduira considérablement le diamètre du tuyau, ce qui affectera négativement le processus d'alimentation en gaz. Une telle canalisation se caractérise par une longue durée de vie et peut résister à des pressions supérieures à 25 bars et à un liquide de refroidissement de 95°C.
Pour résumer tout ce qui précède, il convient de noter que le schéma de tuyauterie d'une chaudière à gaz est établi en fonction de ses caractéristiques et de ses exigences dans chaque cas individuel.
Qu'est-ce que c'est : la tuyauterie de la chaudière ? En termes simples, il s'agit de tout l'équipement nécessaire pour assurer le fonctionnement normal de l'unité de chauffage et transporter le liquide de refroidissement chauffé de l'échangeur de chaleur aux radiateurs. De plus, le schéma de tuyauterie peut varier en fonction du type de chaudière, de son emplacement, ainsi que de la présence équipement supplémentaire.
Il faut se rappeler que solutions prêtes à l'emploi Il n’existe pas de réponse optimale aux exigences de chaque pièce ou bâtiment.
Quels tuyaux conviennent le mieux pour canaliser une chaufferie ?
Chaque matériau a ses propres caractéristiques qui affectent ses performances. Lors du choix des tuyaux pour la tuyauterie d'une chaufferie, vous devez faire attention aux propriétés d'isolation thermique, aux difficultés liées à l'installation ainsi qu'au coût. Les solutions les plus populaires sont :Tuyauterie de chaudière en polypropylène
Poly tuyaux en propylène- un matériau presque idéal pour le cerclage, mais non sans inconvénients. Les avantages incluent :
- Installation facile, l'assemblage du cerclage en polypropylène s'effectue à l'aide d'un fer à souder spécial. De ce fait, tous les travaux de câblage du système de chauffage de la maison et d'installation d'équipements supplémentaires sont réalisés dans un délai d'un jour à une semaine.
- Résistance à la chaleur - les tuyaux en polypropylène pour l'installation de canalisations de chauffage sont renforcés par un renfort en fibre de verre. La fibre de verre en PPT crée un cadre qui protège contre l'expansion lorsqu'elle est chauffée. La conductivité thermique du polypropylène est assez faible, de sorte que les pertes de chaleur le long du trajet chaudière-radiateur sont presque minimes.
- Taux de circulation du liquide de refroidissement - la tuyauterie de la chaufferie en polypropylène présente un autre avantage. Le noyau du pipeline résiste à la formation de dépôts de sel. La vitesse du liquide de refroidissement reste la même tout au long de la durée de vie du produit. La durée de vie déclarée est de 20 ans selon le fabricant.
Tuyauterie de la chaudière avec des tuyaux en cuivre
Installation du harnais des tuyaux de cuivre nécessite un certain professionnalisme de la part du maître, et des coûts matériels importants de la part du client. L'utilisation de tuyaux en cuivre a aussi ses avantages :
- Bon transfert de chaleur du cuivre - la pièce est chauffée non seulement à l'aide des radiateurs eux-mêmes, mais également au fur et à mesure que le liquide de refroidissement se déplace. Le cuivre chauffe bien et ne nécessite pas une grande quantité d'énergie thermique.
- Le cuivre n'est pas sujet à la corrosion. Au fil du temps, les tuyaux en cuivre peuvent se recouvrir d’une fine couche d’oxyde. Mais cela n'affecte pas les performances.
- Les canalisations en cuivre ne craignent pas le gel. La tuyauterie de la chaufferie avec des tuyaux en cuivre élimine les difficultés liées au gel du liquide de refroidissement. Dans ce cas, les tuyaux en acier et en propylène éclatent tout simplement. Le cuivre est plus ductile, il peut donc résister aux charges de gel sans perdre son intégrité.
Comment raccorder correctement une chaudière à combustible solide
La conception de l'équipement TT et le principe de son fonctionnement influencent considérablement les différences de raccordement au système de chauffage. Il convient de considérer que le câblage simultané d'une chaudière électrique et d'une chaudière à combustible solide a également ses propres nuances, qui peuvent affecter leurs performances et leur fonctionnement. Que faut-il prendre en compte dans ce cas ?- Température de retour - ce coefficient ne peut pas être inférieur à 55 degrés ou ce qu'on appelle le « point de rosée ». Dans ce cas, une grande quantité de condensation se produit. C'est pour cette raison qu'il est préférable d'installer correctement une tuyauterie en cuivre pour une chaudière à bois TT à double circuit au sol plutôt que d'utiliser des tuyaux en polypropylène. Le cuivre, qui possède une meilleure conductivité thermique, réduit la quantité de condensation.
- Si nécessaire, plusieurs chaudières peuvent être connectées en un seul réseau. Cela nécessitera l'utilisation d'équipements supplémentaires. Si vous installez et canalisez le chauffage de deux chaudières à bois à combustible solide, un accumulateur de chaleur est nécessaire. Ce schéma est utilisé depuis longtemps en Occident. Son essence est que tout excès de chaleur est accumulé dans un réservoir spécial dont le dispositif ressemble à un thermos. Si la température de chauffage du liquide de refroidissement est insuffisante, l'énérgie thermique provient du réservoir. Tout excès d’énergie thermique va à l’accumulateur de chaleur. Le raccordement d'une chaudière à un ballon tampon (accumulateur de chaleur) implique l'utilisation d'un thermo-mitigeur, ainsi que d'une vanne de soufflage. Unité de mélange thermiqueéviter la surchauffe du liquide de refroidissement.
- Sous certaines conditions, il est possible d'utiliser des tuyaux en polypropylène pour le raccordement d'une chaudière à combustible solide. Mais si l'on considère que le liquide de refroidissement d'un tel système sera constamment chauffé à des températures supérieures à 60 degrés, il devient évident qu'il doit être renforcé et résistant à la chaleur. Les tuyaux avec fibre optique renforcée par une tige en aluminium sont idéaux. En revanche, le schéma de tuyauterie d'une chaudière à combustible solide avec des tuyaux en polypropylène ne nécessite pas, comme dans le cas du cuivre, l'utilisation obligatoire d'une mise à la terre et d'une isolation électrique.
L'installation d'un accumulateur de chaleur nécessitera des coûts supplémentaires, mais en conséquence, l'investissement pourra être rentabilisé dans un avenir proche grâce aux économies sur la consommation excessive de carburant et au fonctionnement des équipements de chauffage.
Comment bien raccorder une chaudière à gaz
Si nous parlons du schéma de raccordement d'une chaudière à gaz, il convient de noter qu'il n'existe tout simplement pas de solutions toutes faites dans ce cas. Le schéma de tuyauterie d'une chaudière à gaz dépend de la manière exacte dont l'équipement de chauffage de l'eau sera utilisé et du nombre de systèmes de chauffage séparés qui fourniront de la chaleur. Les recommandations suivantes doivent être prises en compte :Le schéma de tuyauterie d'une chaudière à gaz au sol monocircuit, de type économe en énergie, doit comprendre l'installation obligatoire d'un by-pass. Le bypass contrôle que la circulation du liquide de refroidissement ne s'arrête pas même après une panne de courant.
Tuyauterie chaudière bois-électricité
Le raccordement d'une chaudière de chauffage utilisant du combustible solide et de l'électricité peut se faire en série et en parallèle. L'essence de l'installation simultanée de deux types d'équipements de chauffage est d'assurer un chauffage continu du liquide de refroidissement dans le système. Cela se fait comme suit:- Une chaudière TT est installée comme source de chauffage principale. Tout au long de la journée, il assure un chauffage normal du liquide de refroidissement.
- La nuit, une fois le bois de chauffage épuisé, la chaudière électrique s'allume automatiquement et continue de chauffer le liquide dans le système jusqu'à ce que la chaudière principale soit inondée.
Comment bien raccorder une chaudière diesel
Le raccordement d'une chaufferie à une chaudière diesel implique l'installation d'équipements supplémentaires qui assurent une circulation stable du liquide de refroidissement et le fonctionnement du système de chauffage. L'utilisation des nœuds suivants est obligatoire :
Raccordement du réservoir de carburant pour chaudière diesel doit prendre en compte l'installation de la pompe d'alimentation en carburant, ainsi que le réservoir de stockage lui-même.
Il est possible de connecter une chaudière diesel et à combustible solide à un seul réseau. Dans ce cas, un circuit séquentiel est assemblé. La principale source de chauffage est l’équipement CT. Lorsque l'intensité du chauffage du liquide de refroidissement diminue, le chauffage diesel s'allume. Étant donné que le dernier modèle contient toute l'automatisation nécessaire, si les paramètres corrects sont installés, l'intervention humaine dans le processus de chauffage continu sera minime. Vous devrez certainement calculer le schéma de câblage du TT de la chaudière diesel et du ballon de stockage de chaleur.
Équipement pour tuyauterie de chaudière de chauffage
L’équipement utilisé pour raccorder toute chaudière de chauffage doit remplir plusieurs fonctions importantes. À savoir:- Assurer des conditions normales de fonctionnement des équipements de chauffage.
- Protéger d'éventuels situations d'urgence: surchauffe du liquide de refroidissement, coup de bélier (se produisent en raison de la différence de température à l'aller et au retour).
- Maintenir la pression requise dans le système.
- - la tuyauterie de la chaudière avec un ballon tampon est exigence obligatoire pour toutes les chaudières TT et souhaitable pour les équipements à gaz. Dans le même temps, les Européens économes installent un accumulateur de chaleur pour une autre raison présentant des avantages importants. Le coût du chauffage d'une pièce à l'aide d'un réservoir est réduit d'environ 5 à 10 %.
- - à la base, ce dispositif est un mécanisme de distribution conventionnel. Une fois le liquide de refroidissement chauffé arrivé, il le dirige conformément aux réglages, alimentant les circuits de chauffage. Le même principe de fonctionnement est utilisé dans les systèmes chauffage central. Pour chaque entrée Bâtiment à plusieurs étages un répartiteur est fourni.
- - cet équipement peut être placé dans une catégorie à part en raison de sa demande. Quelle que soit la configuration de la chaudière elle-même, il peut être nécessaire d'installer une pompe de circulation lors de l'utilisation d'une flèche hydraulique (vous aurez besoin d'un appareil pour chaque circuit), ainsi que lors du chauffage d'une grande surface.
Vous aurez peut-être également besoin de raccords supplémentaires pour les chaudières : soupapes de sécurité, vases d'expansion, pompes à carburant, capteurs de pression, etc.
Composants pour tuyauterie de chaufferie
En plus de l'acquisition équipement spécial, pour assurer le fonctionnement de la chaudière vous aurez besoin Consommables, avec l'aide duquel il sera lié.- Tuyaux en polypropylène pour l'installation de tuyauterie. Pour les travaux, il faudra également acheter un certain nombre d'angles, de filtres grossiers, de robinets et autres composants. Un calcul complet des matériaux pour souder le cerclage en polypropylène peut être effectué par le maître qui réalisera l'installation.
- Isolation - aux endroits où passent les tuyaux de chauffage murs porteurs vous devrez poser le Merilon. Il s'agit d'une isolation spéciale pour les tuyaux, qui remplit simultanément la fonction d'empêcher les pertes de chaleur inutiles et de protéger contre les contraintes mécaniques. Il faudra isoler les canalisations même si le vase d'expansion est placé dans les combles pièce non chauffée. Le cuivre doit être isolé sans faute. Il existe des matériaux spéciaux pour cela, Teploflex, Energoflex.
- Lors de la pose de cloisons à ossature, il faut veiller à isoler la canalisation. L'isolation thermique est particulièrement nécessaire si des canalisations en cuivre ou en métal sont utilisées. Tuyaux métalliques ont une bonne conductivité thermique et chauffent considérablement. Par exemple, le cuivre, lorsque le liquide de refroidissement est chauffé à 90 degrés, affichera à peu près la même température et chauffera le mur, ce qui peut entraîner certains problèmes.
Faire appel à des spécialistes pour rédiger une documentation de conception compétente, y compris un schéma de tuyauterie pour l'équipement de chauffage de l'eau chaude, contribuera à augmenter considérablement sa durée de vie et son coefficient de transfert de chaleur.
Il n’existe pas de solutions toutes faites pour la tuyauterie des chaudières ! Le projet est élaboré sur place en tenant compte des caractéristiques du bâtiment chauffé et du système de chauffage utilisé.
La croissance du volume de construction de chalets individuels a fait sensation sur le marché des équipements de chauffage, car il est impossible de créer un cadre de vie confortable dans une maison sans avoir système fiable chauffage et fourniture d'eau chaude. De nombreuses zones résidentielles sont équipées d'une alimentation principale en gaz, leurs résidents achètent donc des générateurs de chaleur à gaz fiables. Les experts estiment qu'une bonne source n'est qu'une partie du succès et que la clé réside dans une tuyauterie appropriée de la chaudière à gaz, qui protégera système thermique contre les coups de bélier et assurera un chauffage confortable de la maison.
Cerclage - complexe travaux d'ingénierie combiner des éléments et des unités d'un circuit thermique en un seul complexe générateur de chaleur. Sa conception exécutive est absolument individuelle et dépend du type de chaudière, du nombre de circuits de chauffage, de l'automatisation de la sécurité, du câblage du système de chauffage intérieur et de l'alimentation en eau chaude.
Tous les gaz principaux et auxiliaires équipement de chaudière fait référence à des objets présentant un danger accru ; toute erreur, même la plus petite, dans la tuyauterie entraîne des processus irréversibles et peut provoquer une urgence et un risque d'incendie dans les systèmes de survie. À cet égard, il est important d'aborder la tuyauterie d'une chaudière à gaz de manière responsable, en respectant les normes et règles de sécurité concernant l'installation et le fonctionnement des chaudières à gaz. batterie faible. C'est pourquoi il est recommandé de confier tous les travaux de conception, d'installation et de mise en service des équipements de chaudières à gaz à du personnel certifié.
Fonctions de la tuyauterie de la chaudière :
- Répartition uniforme des flux de chaleur et de vitesse dans tout le système de chauffage et d'eau chaude.
- Compensation de la dilatation thermique des systèmes de canalisations et des surfaces de chauffage chaudes (chaudière, chaudière).
- Élimination de l'air de l'eau de refroidissement.
- Surveillance de la moyenne pression et évacuation de l'eau, si le seuil maximum est dépassé, à travers le vase d'expansion.
- Création d'un mode spécifié dans le trajet gaz-air de la chaudière.
- Maintien d'une température sanitaire de l'air intérieur dans une installation chauffée.
Principaux composants et éléments du système
La tuyauterie est associée à des équipements et composants spécifiques du circuit d'alimentation en chaleur et dépend de la puissance thermique raccordée à l'installation. Il existe des projets d'installation standards qui peuvent devenir la base du développement d'activités spécifiques.
Équipements inclus dans le schéma de tuyauterie de la chaudière à gaz :
- Les chaudières à gaz sont une source de chaleur, elles se distinguent par une circulation naturelle ou forcée, un circuit simple ou double, un mur ou un sol.
- Purge d'air - pour éliminer les poches d'air du circuit de chauffage.
- Le collecteur de boue est un récipient permettant de collecter et de purifier les substances en suspension dans l'eau du réseau.
- Un vase d'expansion à membrane pour protéger le système des surpressions et des coups de bélier lors de l'allumage de l'appareil et de l'atteinte des paramètres de température de fonctionnement.
- Filtres adoucissants – pour purifier l’eau des sels de dureté.
- Tuyaux de dérivation – pour connecter les conduites de chauffage entrantes et sortantes.
- Capteurs, manomètres et thermomètres - pour connecter l'automatisation de contrôle et de sécurité.
- Conduits de gaz et cheminée– éliminer les produits de combustion usés dans l’environnement.
- Un filtre à gaz pour purifier le gaz des impuretés est installé derrière le robinet de gaz.
- Pompes, extracteurs de fumée, ventilateurs - pour assurer le mouvement de l'eau et des fluides gaz-air.
- Les radiateurs de chauffage sont des dispositifs à l'aide desquels un échange de chaleur se produit entre la température du liquide de refroidissement et l'air à l'intérieur de la pièce.
Règles de tuyauterie d'une unité à gaz
Avant de commencer à acheter du matériel, vous devez vous procurer Caractéristiques et l'autorisation de se connecter au gazoduc. Le service gaz détermine s'il est en principe possible d'installer une chaudière à gaz, ainsi que les paramètres du gaz au point d'insertion. Ensuite, les propriétaires réalisent un projet d'approvisionnement en chaleur avec la participation d'un organisme spécialisé, qui indiquera nécessairement le schéma de tuyauterie. Ce projet convenu avec le service de gaz. Cela prend généralement entre 2 semaines et 3 mois, après quoi vous pouvez acheter du matériel à gaz.
Règles de base:
- Avant de commencer à raccorder une chaudière à gaz pour le chauffage, celle-ci est installée dans une pièce qui doit avoir des paramètres minimaux : une superficie d'au moins 4 m, une hauteur de 2,5 m et une largeur de porte d'au moins 0,8 m.
- La pièce doit être ventilation naturelle et des fenêtres dont les dimensions dépendent de la superficie : 0,3 m2 de fenêtre pour 10 m2.
- Tous les gazoducs doivent être en acier.
- Le tuyau de cheminée doit avoir un diamètre, en fonction de la puissance de la chaudière : 30 kW - 13 cm, 40 kW - 17 cm, mais il ne doit pas être plus petit que le tuyau d'évacuation des fumées de la chaudière.
- La partie extérieure de la cheminée doit être au moins 50 cm plus haute que le toit.
- Une sonde gaz et un robinet d'arrêt gaz sont installés dans la chaufferie.
- L'équipement de la chaudière doit être mis à la terre de manière fiable.
- Le système d'alimentation est équipé d'une protection actuelle et d'une isolation thermique.
- Liaison d'éléments diagramme de travail réalisée à l'aide de canalisations, qui peuvent être en acier galvanisé, en fonte, en cuivre et en plastique.
- Les tronçons de tuyaux à la sortie de la chaudière sont uniquement en métal, d'une longueur d'au moins 1,0 m.
Récemment, les tuyaux métal-plastique avec raccords à sertir et les tuyaux en polypropylène avec renfort en aluminium ont gagné en popularité. Leur avantage est indéniable, et en termes de fiabilité montage rapide, et en termes de coût, en outre, un tel pipeline peut résister à des pressions allant jusqu'à 25 bars et à des températures ambiantes allant jusqu'à 95 C. Cependant, les options présentent également des inconvénients qui doivent être pris en compte lors du démarrage de l'installation. Les raccords à sertir sont très sensibles à la qualité de l'assemblage : au moindre désalignement, des fuites d'eau peuvent se produire et le polypropylène a un coefficient d'allongement élevé à des températures supérieures à 50°C.
Caractéristiques des chaudières à gaz à tuyauterie en polypropylène :
- Les circuits de chauffage et d'eau chaude sont réalisés avec : des canalisations PN 25 (2,5 atm, 95 C) et PN 20 (2,0 atm, 80 C).
- Le raccordement des canalisations et raccords s'effectue à froid ou soudage à chaud, les connexions filetées sont utilisées pour se connecter aux zones métalliques.
- Pour éviter la destruction des tuyaux en polypropylène, des boucles de compensation sont installées.
- Les tuyaux multicouches ont un renfort interne pour compenser. La feuille réduit l'allongement de 2 fois et la fibre de verre de 5 fois.
- Avant le soudage, retirez le film des canalisations renforcées.
Options pour les schémas de cerclage
La version classique de la tuyauterie d'une chaudière à gaz est celle où le liquide de refroidissement monte à travers l'alimentation, pénètre dans les colonnes montantes puis sur les radiateurs. Le degré de chauffage de la pièce dépend du nombre de radiateurs installés, équipés de selfs et de cavaliers. Le liquide de refroidissement froid est renvoyé à la chaudière via la conduite de retour inférieure.
Les schémas de cerclage les plus courants actuellement sont :
- Système gravitationnel ;
- forcé avec pompe de circulation ;
- circuit unique;
- double circuit;
- chaudière murale;
- installation au sol de l'unité.
Cerclage dans les systèmes gravitaires
Le système de chauffage gravitationnel est autorisé pour la mise en œuvre de l'apport de chaleur à des objets d'une superficie ne dépassant pas 100 m2 et doit être réalisé exactement comme prévu. S'il y a des erreurs lors du choix des tuyaux ou si les pentes ne sont pas entretenues, le système ne fonctionnera pas.
Le principe de fonctionnement du système est basé sur la différence de densité de l'eau chaude et froide. L'eau chaude monte jusqu'aux radiateurs, où elle dégage de la chaleur dans l'air ambiant, puis le liquide de refroidissement froid refroidi descend et pénètre par le flux de retour dans l'entrée de la chaudière de chauffage. La condition principale pour la tuyauterie est d'assurer des pentes de tuyauterie d'au moins 3 degrés.
Avantages du régime :
- Simplicité de conception ;
- accessibilité de l'installation;
- fonctionnement silencieux de la chaudière;
- longue durée de vie.
Comme inconvénients, les utilisateurs notent :
- Longue période de chauffage ;
- l'incapacité de réguler avec précision la température à l'intérieur de l'air ambiant ;
- grossier apparence installation de tuyaux avec des pentes qui gênent l'intérieur des locaux.
Connexion de systèmes avec une pompe de circulation
Les pompes de circulation sont incluses dans le circuit dans un système à haute résistance lorsqu'elles ne peuvent être surmontées par la circulation naturelle ou dans des chaudières à double circuit, où le liquide de refroidissement pénètre alternativement dans le circuit de chauffage ou d'eau chaude. La pompe augmente le taux de circulation du fluide à travers le système de chaudière, ce qui augmente l'efficacité du système de chauffage de 30 %. De plus, le fait qu’un tel système soit plus facile à automatiser et permette un réglage plus fin est positif. régime thermiqueà l'intérieur.
L'installation de la pompe sur la canalisation réseau s'effectue à l'aide d'écrous-raccords, le plus souvent livrés avec la chaudière, mais peuvent également être achetés dans le commerce de détail. Lors de l'installation de l'unité de pompage de l'eau du réseau, elle ne doit pas être soumise à des forces lors du serrage des écrous. Un filtre à impuretés en maille est installé à l'entrée de la pompe pour protéger Roue de travail l'unité de la saleté et des dépôts. La pompe est isolée de l'équipement principal par des vannes à bille pour la réparation et l'entretien.
Les nuances du cerclage
Malgré le fait que le harnais soit sélectionné individuellement, il existe plusieurs dispositions générales que vous devez respecter :
- Chaudière pour circuits avec circulation naturelle les systèmes de chauffage sont installés sous le niveau des radiateurs.
- La base pour l'installation des unités au sol doit être constituée de matériaux incombustibles.
- Les chaufferies sont équipées de ventilation et d'éclairage.
- Le groupe chaudière est relié à l'inclusion d'une cheminée coaxiale.
- Après le montage et l'installation de l'unité et des systèmes de désenfumage, un groupe de sécurité est installé : un manomètre de contrôle, une soupape de surpression puis un purgeur d'air.
- Vase d'expansion installé entre la flèche hydraulique et le bloc chaudière.
Raccordement d'une chaudière murale
Ce type de chaudière permet une installation au mur dans la cuisine. Structurellement, il est réalisé de telle manière que la tuyauterie nécessaire a déjà été réalisée par le fabricant, et ses éléments sont fournis en kit. Selon le type d'unité, elles peuvent être à circuit simple ou double, le nombre de tuyaux pour la tuyauterie peut donc différer.
Algorithme de tuyauterie d'une chaudière à gaz double circuit :
- Retirez les bouchons des tuyaux.
- Installez une crépine sur la conduite de retour pour éliminer la saleté et les matières en suspension.
- Un filtre est installé pour purifier l'eau des sels de dureté ; il peut être installé sur l'arrivée d'eau commune du robinet.
- Lors de la tuyauterie d'une chaudière à gaz murale, des vannes d'arrêt et de régulation avec raccords amovibles, par exemple « américains », sont installées.
- Les conduites d'eau froide sont situées du côté gauche par rapport au centre de la chaudière, et les conduites d'eau chaude sont situées à droite.
- La chaudière est raccordée au réseau de gaz avec l'assistance d'un spécialiste certifié ; l'agrément final de la chaudière sera délivré par un représentant de la société de gaz de ville après un essai de l'équipement de la chaudière.
- Lors de la tuyauterie d'une chaudière à gaz à double circuit, les raccords de gaz filetés sont scellés uniquement avec du câble.
- Installez un filtre spécial sur le robinet d'arrêt de gaz.
- La chaudière est reliée au réseau de gaz avec un tuyau ondulé et un écrou-raccord avec un joint paranitique.
Raccordement d'une chaudière gaz au sol
Ce système nécessite une pièce séparée pour abriter la chaudière, car les modèles au sol sont grands et ont souvent conception ouverte four fonctionnant avec circulation naturelle à travers le trajet gaz-air. Le schéma comprend également une pompe pour la circulation du liquide de refroidissement, notamment pour la tuyauterie d'une chaudière à gaz à double circuit et pour un niveau de chauffage multiforme : nombre d'étages, différents types chauffage – radiateur et « plancher chaud ».
Le circuit de chauffage à double circuit (chauffage et eau chaude sanitaire) se compose de 5 tuyaux : 1 - gaz, 4 - eau liquide de refroidissement. Le premier est relié au dispositif brûleur par un robinet à tournant sphérique.
Schéma de raccordement de l'eau de refroidissement lors de la tuyauterie d'une chaudière à gaz au sol :
- Entrée de chaudière de chauffage ;
- puissance de la chaudière de chauffage ;
- Entrée de l'échangeur de chaleur ECS ;
- puissance de l’échangeur thermique ECS.
La répartition des débits d'eau est automatique, réalisée par une vanne à trois voies, une flèche hydraulique ou des vannes d'équilibrage.
Pour raccorder une chaudière gaz au sol avec des réseaux de chaleur étendus et une longue distance, il est recommandé de raccorder 2 capteurs avec une pompe autonome, par exemple un pour le fluide caloporteur basse température jusqu'à 50 C pour un système « plancher chaud », et l'autre jusqu'à 90 C pour les radiateurs classiques.
Pour réduire la température, le collecteur peut être équipé d'un mélangeur ou d'une vanne trois voies avec servomoteur installé entre l'alimentation et le retour sur le peigne. Des capteurs permettent de régler différentes températures dans les circuits.
Ainsi, pour bien attacher la chaudière, vous aurez besoin non seulement d'une expérience dans les travaux d'installation, mais également du strict respect des règles de fonctionnement de l'État et des exigences du fabricant.
Lors de la construction chauffage autonomeÀ la maison, il est important de bien réfléchir et réaliser la tuyauterie des chaudières à gaz, à combustible solide et électriques. considérons schémas possibles et des éléments de tuyauterie, parlons des circuits classiques, de secours et spécifiques, ainsi que des principaux équipements de ces circuits.
Les principes de base de la tuyauterie d'une chaudière de toute conception sont la sécurité et l'efficacité, ainsi que la durée de vie maximale de tous les éléments du système de chauffage. Considérons diverses options organiser le chauffage de manière à ce que lorsque construction individuelle prendre une décision éclairée et la plus appropriée pour un cas particulier.
Raccordement de la chaudière aux alimentations électriques
Si la chaudière fonctionne au gaz, elle doit être alimentée en gaz. Pour l'approvisionnement principal en gaz, cela doit être effectué par un employé du service gaz. Si le chauffage provient de ballons, vous devez conclure un contrat de location avec Gaztekhnadzor et confier l'installation à une entreprise autorisée à ce type travaux Tous les travaux liés au gaz sont potentiellement dangereux et ce n’est pas le moment où vous devriez économiser de l’argent et faire les travaux vous-même.
1. Alimentation en chauffage. 2. Eau chaude pour les besoins domestiques. 3. Gaz. 4. Eau froide vers le circuit ECS. 5. Retour chauffage
Lors de l'utilisation de gaz en bouteille, il faut utiliser un réducteur qui combine un groupe de bouteilles
La chaudière électrique doit être raccordée au réseau. La chaudière et la boîte à bornes doivent être mises à la terre ; toutes les connexions sont réalisées avec un câblage en cuivre d'une section non inférieure à celle spécifiée dans la fiche technique de l'équipement.
Une chaudière à combustible solide est toujours autonome et ne nécessite que le raccordement des canalisations de chauffage et d'alimentation en eau chaude. Seuls les blocs nécessitent des connexions aux circuits d'alimentation électrique contrôle automatique, s'ils sont impliqués.
Chaudières à simple et double circuit
Les chaudières à circuit unique sont principalement conçues pour le chauffage. Un seul circuit les traverse, comprenant l'automatisme, la canalisation de distribution et les radiateurs. Une chaudière à chauffage indirect peut également être incluse dans le circuit pour alimenter en eau chaude les mitigeurs de lavabos, douches et baignoires. La puissance de la chaudière est sélectionnée avec une réserve de marche appropriée. La faisabilité d'une telle connexion est dans la plupart des cas quelque peu discutable, car elle perturbe la stabilité du système de chauffage par un retrait soudain de chaleur. Le problème peut être résolu en équipant le circuit d'un système de contrôle complexe, qui, dans certains modèles, peut être fourni avec la chaudière.
Chaudière à circuit unique avec chaudière à chauffage indirect : 1. Chaudière. 2. Tuyauterie de la chaudière. 3. Radiateur. 4. Chaudière à chauffage indirect. 5. Entrée d'eau froide
Dans une chaudière à double circuit, l'alimentation en eau chaude, avec le chauffage, fait partie des fonctions de la chaudière et constitue l'un de ses deux circuits de circulation. Un fonctionnement plus stable des deux systèmes est obtenu lorsque les chaudières sont équipées de deux échangeurs de chaleur séparés pour deux circuits. Caractéristique du système : pas de ballon de stockage d’eau chaude.
Raccordement d'une chaudière double circuit : 1. Chaudière. 2. Tuyauterie de la chaudière de chauffage. 3. Circuit de chauffage. 4. Entrée d'eau froide
Schéma de tuyauterie de chaudière pour circulation naturelle
La circulation naturelle est basée sur les lois de la physique - dilatation thermique du liquide de refroidissement et gravité, c'est pourquoi la tuyauterie de la chaudière ne comprend pas d'équipement sous pression.
Pour que l’eau du circuit circule en continu, plusieurs règles doivent être respectées.
La chaudière doit être située au point le plus bas de la maison, de préférence au sous-sol ou dans une fosse spécialement aménagée.
La canalisation allant du point haut aux radiateurs de chauffage, et de ceux-ci au « retour », doit être réalisée avec une pente d'au moins 0,5° pour réduire la résistance hydraulique du système.
Chauffage à circulation naturelle. H - la différence entre les niveaux des conduites d'alimentation et de retour, détermine la pression dans le circuit de chauffage
Le diamètre des tuyaux de distribution de chauffage doit garantir une vitesse de l'eau d'au moins 0,1 m/s et d'au plus 0,25 m/s. Ces valeurs doivent être prises au préalable et vérifiées par calcul, en fonction de la différence de température à l'entrée et à la sortie (pente) et de la différence de hauteur le long des axes de la chaudière et des radiateurs (au moins 0,5 m).
Les circuits gravitationnels de la chaudière peuvent être de types ouverts et fermés. Dans le premier cas, un vase d'expansion est installé au point le plus haut du système (dans les combles ou en toiture). Type ouvert, il fait également office de bouche d'aération.
Le système fermé est équipé d'un réservoir à membrane situé au même niveau que la chaudière. Parce que systeme ferme n'a pas de contact direct avec l'atmosphère, il doit être équipé d'un groupe de sécurité (manomètre, soupape de sécurité et purgeur d'air). Le groupe est positionné de manière à ce que la vanne d'air soit au point le plus haut du circuit.
Les systèmes de circulation naturelle sont indépendants de l’alimentation électrique et sont plus courants là où les réseaux électriques sont absents ou peu fiables.
Schéma de tuyauterie de chaudière pour circulation forcée
Le stimulateur du mouvement de l'eau dans un circuit à circulation forcée est une pompe de circulation. Les circuits peuvent également être ouverts (avec un vase d'expansion de type ouvert) et fermés (avec un vase à membrane et un groupe de sécurité).
En règle générale, la pompe de circulation est installée à l'endroit où la température de l'eau est la plus basse - à son entrée dans la chaudière, et est montée sur le même site. La pompe est sélectionnée en fonction du calcul de chauffage, indiquant le débit de liquide de refroidissement requis et les caractéristiques de la chaudière. Le débit de liquide de refroidissement est régulé en fonction de la température de l'eau de retour sur la base d'une impulsion d'un capteur installé à l'entrée de la chaudière.
1. Chaudière. 2. Groupe de sécurité. 3. Vase d'expansion. 4. Pompe de circulation. 5. Radiateurs de chauffage
Câblage d'un système de chauffage monotube et bitube
Le système monotube est largement utilisé dans Tours d'appartements vieux batiments. La température de l'eau d'un radiateur à l'autre diminue constamment, ce qui entraîne un apport de chaleur inégal aux pièces individuelles. Dans un système à deux tuyaux, le liquide de refroidissement est réparti uniformément sur tous les radiateurs ; lorsqu'il perd de la température, il pénètre dans le deuxième tuyau - le « retour ». Ainsi, système à deux tuyaux fournit à la maison une chaleur plus uniforme.
1. Schéma de câblage monotube. 2. Schéma de câblage bitube
Schéma de câblage du collecteur du système de chauffage
S'il y a un grand nombre de radiateurs de chauffage situés à différents étages, ou lors du raccordement d'un « plancher chaud », le meilleur schéma de câblage est celui d'un collecteur. Au moins deux collecteurs sont installés dans le circuit de la chaudière : sur l'arrivée d'eau - distribution, et sur le « retour » - collecte. Le collecteur est un morceau de tuyau dans lequel sont insérés des robinets avec des vannes pour permettre la régulation de groupes individuels.
Groupe de collectionneurs
Un exemple de raccordement d'un circuit de chauffage et d'un système « plancher chaud » à l'aide d'un groupe collecteur
La distribution des collecteurs est également appelée radiale, car les tuyaux peuvent rayonner dans différentes directions dans toute la maison. Un tel schéma dans maisons modernes l'un des plus courants et considéré comme pratique.
Anneaux primaire-secondaire
Pour les chaudières d'une puissance de 50 kW ou plus ou un groupe de chaudières destinées au chauffage et à l'alimentation en eau chaude des grandes maisons, un schéma en anneau primaire-secondaire est utilisé. L'anneau primaire est constitué de chaudières - générateurs de chaleur, d'anneaux secondaires - consommateurs de chaleur. De plus, les consommateurs peuvent être installés sur la branche aller et être à haute température, ou sur la branche inverse et être dits basse température.
Pour garantir l'absence de distorsions hydrauliques dans le système et séparer les circuits, un séparateur hydraulique (flèche) est installé entre les anneaux de circulation primaire et secondaire. Il protège également l'échangeur thermique de la chaudière des chocs hydrauliques.
Si la maison est grande, un collecteur (peigne) est installé après le séparateur. Pour que le système fonctionne, vous devez calculer le diamètre de la flèche. Le diamètre est choisi en fonction de la productivité (débit) maximale de l'eau et de la vitesse d'écoulement (pas supérieure à 0,2 m/s) ou en fonction de la puissance de la chaudière, en tenant compte du gradient de température (valeur recommandée Δt - 10 ° C). .
Formules de calculs :
- G - débit maximum, m 3 /h ;
- w est la vitesse de l'eau à travers coupe transversale flèches, m/s.
- P-puissance de la chaudière, kW ;
- w—vitesse de l'eau à travers la section transversale de la flèche, m/s ;
- Δt – gradient de température, °C.
Circuits de secours
Dans les systèmes à circulation forcée, les pompes dépendent d'une alimentation électrique qui peut être interrompue. Pour éviter une surchauffe des chaudières, susceptible d'endommager les équipements ou même d'entraîner une dépressurisation, les chaudières sont équipées de systèmes d'urgence.
Première option. Source Alimentation sans interruption ou un générateur qui alimentera les pompes de circulation. En termes d'efficacité, cette méthode est l'une des plus optimales.
Deuxième option. Un petit anneau de réserve est en cours d'installation, fonctionnant selon le principe gravitationnel. Une fois déconnecté pompe de circulation Un circuit de circulation naturelle est inclus dans le système, assurant le transfert de chaleur vers le liquide de refroidissement. Le circuit supplémentaire ne peut pas assurer un chauffage complet.
Troisième option. Lors de la construction, deux circuits à part entière sont posés, l'un fonctionne selon le principe gravitationnel, le second utilisant des pompes. Les systèmes doivent avoir la capacité d’échanger de la chaleur et de la masse pendant une période d’urgence.
Quatrième voie. Si l'approvisionnement en eau est centralisé, alors lorsque les pompes sont éteintes eau froide alimenté aux circuits de chauffage par un tuyau spécial avec une vanne d'arrêt (un cavalier entre l'alimentation en eau et les systèmes de chauffage).
En conclusion, nous vous suggérons de regarder une vidéo sur les règles de calcul d'un système de chauffage monotube pour une maison privée.
Le raccordement du chauffage au gaz est l'une des étapes les plus importantes de l'amélioration d'un bâtiment. Le confort de la maison pendant de nombreuses années dépend de la qualité des matériaux sélectionnés et des travaux d'installation. Le schéma de tuyauterie correct pour une chaudière à gaz protège le système des surcharges et assure un chauffage uniforme de toutes les pièces.
L'article que nous proposons fournit des règles et des schémas de câblage testés par la pratique pour les équipements de chauffage. Des recommandations sont données pour garantir la qualité du montage et un fonctionnement impeccable de la chaudière. Les informations que nous fournissons sont basées sur les réglementations en matière de construction.
La tuyauterie fait référence aux tuyaux et mécanismes conçus pour fournir du liquide de refroidissement de la chaudière aux radiateurs. Il s'agit de la quasi-totalité du système de chauffage, à l'exception des batteries.
Le système se compose de nombreux composants, mais même un non-professionnel peut installer la tuyauterie de chaudière la plus simple. Mais si tu en as besoin circuit complexe, il est préférable de contacter un maître expérimenté.
Il est préférable d'installer la chaudière dans une pièce séparée, par exemple dans une dépendance, une chaufferie ou un sous-sol, car la tuyauterie implique des tuyaux et des mécanismes supplémentaires, ce qui n'est pas toujours pratique. Cependant, s'il n'y a pas assez d'espace équipement de chauffage installé dans la maison
Le choix du schéma de tuyauterie pour chaque maison spécifique dépend du type de chaudière, des caractéristiques de construction et du type de système de chauffage.
Galerie d'images