Konsep asli dari proyek ini adalah sebagai cara Anda memamerkan keterampilan pertukangan Anda kepada teman-teman dengan membawa minuman ke pesta atau piknik. Namun kami juga berpikir untuk membuat media ini tidak hanya untuk bersenang-senang, tetapi juga untuk pekerjaan yang serius. Untungnya, kami yakin bahwa kaleng logam yang rapi, yang memudahkan untuk menyimpan pengencang dan aksesori kecil, memakan ruang sebanyak botol minuman. Dan jika Anda perlu menempatkannya lebih banyak botol, pengencang atau perkakas, buat saja kotaknya lebih panjang (lihat foto di akhir artikel).
Kevin Boyle, Pemimpin Redaksi
Bagaimana koneksi dibuat
1. Gunting dinding ujung dari bahan 13 mm A dan potongan uji dengan lebar yang sama, tetapi panjang 305 mm (Gbr. 1). Sisihkan adonan. Kemudian potong dinding memanjang B sesuai dimensi yang ditentukan.
2. Pasang bantalan kayu pada kepala penahan melintang (bersudut). Angkat mata gergaji hingga ketinggian 25 mm dan posisikan pagar memanjang (paralel) pada jarak 13 mm dari tepi luar mata gergaji (lihat “Ujung Master”). Buat potongan di seluruh sudut dinding memanjang B (foto A).
Menekan dinding B pada penahan memanjang, membuat potongan di setiap sudut. Bantalan pagar silang menopang benda kerja dan mencegah chipping.
nasihat Guru. Pengaturan tanpa pengukuran. Dengan gergaji dicabut, gunakan dinding ujung A sebagai templat untuk memasang pagar sobek. Tekan salah satu sisi papan ke pagar sobekan dan geser hingga sisi yang berlawanan sejajar dengan tepi luar gigi mata gergaji. Periksa keakuratan penyelarasan dengan menyentuhnya menggunakan jari Anda.
3. Buang bahan berlebih (foto B). Selesaikan potongan dalam beberapa lintasan, pindahkan benda kerja ke pagar sobekan dan kembali ke atas mata gergaji untuk memangkas tepinya. (foto C).
Buat lintasan tambahan dari ujung ke tengah dinding B, gerakkan benda kerja ke arah pemberhentian memanjang sesuai lebar potongan setelah setiap lintasan.
Untuk membersihkan permukaan, gerakkan dinding B ke arah penahan memanjang dan kembali melalui bagian tertinggi mata gergaji. Bantalan pagar silang akan membantu menopang dan memandu benda kerja.
Lakukan pemotongan percobaan untuk menghindari kerepotan dengan detail proyek. Jika perlu, buat potongan kedua, ketiga, atau bahkan keempat pada sudut trim bebas.
4. Turunkan mata gergaji hingga ketinggian 13 mm dan pasang pembatas robekan pada jarak 76 mm dari tepi luar mata gergaji. Pasang penghenti dari trim ke pelat penghenti melintang, letakkan pada jarak 352 mm dari penghenti memanjang. Mengambil benda uji yang sudah disiapkan melangkah 1, dan, dengan menekan ujungnya pada penahan memanjang, buat satu potongan, lalu tekan ujung yang berlawanan pada penahan dan buat potongan kedua (fotoD). Bandingkan lebar tonjolan pada dinding memanjang B dengan jarak antara tepi luar potongan tersebut. Ubah pengaturan gergaji sesuai kebutuhan lalu buat potongan yang sama pada kedua tepi dinding ujung. A.
Catatan. Lebih baik jika lebar potongannya sedikit lebih kecil, karena Anda bisa mendapatkan potongan yang presisi menggunakan amplas atau kikir.
5. Sama seperti saat membentuk dinding memanjang DI DALAM, singkirkan material berlebih di antara potongan di dinding ujung A dalam beberapa operan tambahan. Periksa kekencangan sambungan dan, jika perlu, sesuaikan lebar potongan.
Menggergaji kontur dan perakitan
1. Perbesar setengah templat kontur sebanyak 2 kali (Gbr. 2). Tempelkan dengan perekat semprot ke sepotong hardboard 6 mm, potong dan amplas tepi templat. Belum perlu mengebor lubang.
Sejajarkan tepi templat dengan tepi dinding ujung A, tekan pada persegi, dan jiplak tepi lengkung templat dengan pensil.
2. Tempatkan di dinding ujung A kombinasi persegi, sejajarkan tepi atas penggarisnya dengan tepi atas potongan. Tempatkan bagian bawah templat pada persegi, jiplak garis luarnya dengan pensil (foto E). Balikkan templat ke sisi yang lain, sejajarkan dan ulangi. Tandai bagian tengah lubang 19mm di lokasi yang ditunjukkan.
3. Kencangkan kedua ujung dinding A bersama selotip dua sisi, menyelaraskan ujung dan tepinya. Gergaji sepanjang garis luar dan ampelas tepinya hingga membentuk garis, lalu bor lubang 19 mm (lubang 6 mm akan dibuat nanti). Pisahkan bagian-bagiannya dan amplas terakhir dengan amplas 220 grit.
4.
Pasang pemotong berlubang 6 mm ke dalam collet router yang dipasang di meja dan sesuaikan offsetnya sehingga jarak dari bagian bawah pemotong ke meja adalah 6 mm. Keringkan (tanpa lem) sambungkan dinding A, B, kencangkan dengan klem, dan giling lidah dan alur di bagian dalam dinding di sekeliling keseluruhan.5. Untuk menentukan dimensi bagian bawah DENGAN mengukur jarak antara ujungnya A dan memanjang DI DALAM dinding, lalu tambahkan 11 mm pada setiap dimensi. Potong bagian bawah sesuai ukuran ini dan bulatkan sudutnya agar pas dengan lekukan dan lidah dinding.
Pisahkan sisi-sisinya dan pasang kembali kotaknya, ganti bagian bawah untuk memastikan semua sambungan sudah benar. Sesuaikan bagian bawah jika perlu, lalu ampelas bagian samping dan bawah yang memanjang dengan amplas grit 220. Oleskan lem pada lidah dan potongan samping, rakit kotak dengan bagian bawah pada tempatnya, dan kencangkan dengan klem. Periksa kelurusan rakitan.
6. Setelah lem mengering, bor lubang sedalam 6mm, 25mm di tengah setiap tonjolan dinding A, B (Gbr. 1). Potong pasak dari batang kayu bundar dengan diameter 6 mm D panjang 25 mm dan rekatkan ke dalam lubang. Saat lem sudah kering, amplas hingga rata dengan permukaan dinding.
7. Jika mau, Anda dapat menambahkan partisi E, F, menyesuaikan tambangnya dengan dimensi internal kotak IKLAN. Potong slot menggunakan gergaji, tekan partisi pada bantalan pagar melintang. Selesaikan pengamplasan partisi dengan amplas 220 grit.
8. Dari batang kayu bulat berukuran 19 mm, potong potongan sepanjang 273 mm untuk pegangannya G. Lewatkan melalui lubang di dinding ujung A dan sejajarkan di tengah. Tandai pada pena sisi luar dinding, lingkari dengan pensil. Keluarkan pegangannya dan bor lubang 6mm sedalam 13mm di sebelah garis (Gbr. 1,"Nasihat dari Guru") Ampelas talang kecil di sekitar ujung pegangan. Kemudian pasang kembali pegangannya ke tempatnya, potong pinnya N panjang yang ditentukan dan rekatkan ke dalam lubang pegangan.
nasihat Guru. Cara menjinakkan pasak yang sulit diatur. Untuk memastikan batang dowel bundar tetap tidak bergerak saat mengebor lubang, kencangkan dengan balok prisma. Membuat balok prisma sangatlah mudah: miringkan mata gergaji pada sudut 45° dan buat dua potongan berpotongan pada selembar papan tebal.
9. Setelah lem mengering, aplikasikan lapisan akhir. (Kami menggunakan pernis nitro semi-matte dalam kaleng aerosol.) Jika Anda membuat partisi E, F, masukkan ke dalam kotak. Jangan merekatkannya agar Anda bisa melepasnya jika perlu. Sekarang Anda dapat menggunakan operator untuk bekerja atau bersantai, atau mungkin keduanya.
Butuh kotak perkakas? Tingkatkan panjangnya
Tas jinjing yang lebih panjang akan memungkinkan Anda menyimpan lebih banyak perkakas dan lebih banyak pengencang. Cukup tambah panjang dinding memanjang DI DALAM, dasar DENGAN dan pegangan G (Gbr. 1). Jika Anda ingin membagi ruang interior menjadi beberapa kompartemen, buatlah lima partisi pendek E dan membuat partisi pusat lebih panjang F. Untuk kotak pembawa ini kami menggunakan papan kayu ek yang dipotong radial dan batang pegangan kayu kenari bundar G dan pasak D.
Pengangkut yang nyaman ini sepenuhnya buatan tangan. Anda dapat mengulangi kelas master ini dan mendapatkan produk yang sama, yang dapat menampung enam botol minuman apa pun dalam wadah kaca standar, gelas logam atau plastik, dan pembuka. Botol-botol tersebut terpasang dengan aman di dalam wadahnya dan dapat diletakkan di bagasi mobil saat akan piknik atau berkunjung. Detail proses dan templat dengan penandaan diberikan di kelas master.
Bahan
Untuk membuat wadah botol untuk 6 tempat, siapkan:
- potongan kayu lapis, 25 mm;
- kaki karet dengan pengikat berulir, 3 pcs.;
- baut dan mur;
- pegangan logam;
- lem kayu;
- bor dengan bor cincin;
- gergaji pita atau gergaji ukir;
- penjepit;
- mesin amplas atau amplas;
- noda kayu atau pernis.
Langkah 1. Cetak templat di bawah ini, sesuaikan dengan diameter botol kaca standar.
Langkah 2. Lampirkan templat ke potongan kayu lapis dan potong bagian yang kosong untuk dibawa. Bagian bawah terdiri dari lingkaran padat dengan slot untuk botol. Yang paling atas adalah sepotong kayu lapis, dipotong seperti bagian atas alasnya, tetapi dengan lingkaran di tengahnya dan lubang kecil untuk pembuka botol yang memanjang. Omong-omong, potongan di tengah atas harus sesuai dengan diameter cangkir minuman.
Langkah 3. Setelah memotong bagian yang kosong, pastikan untuk mengampelasnya. Buat alur di bagian bawah. Mereka tidak harus lintas sektoral. Berhati-hatilah agar lekukan di bagian atas dan bawah wadah harus sesuai.
Langkah 4. Potong lingkaran dari kayu lapis. Mereka perlu ditumpuk, direkatkan, dan kemudian diampelas. Mereka menyesuaikan ketinggian pengangkutan. Dalam hal ini, diperlukan empat di antaranya, tetapi semuanya akan tergantung pada ketebalan kayu lapis dan tinggi botol kaca.
Langkah 5. Rekatkan setumpuk lingkaran ke dasar dan atas wadah.
Langkah 6. Hiasi dudukannya dengan noda, cat, atau pernis sesuai kebijaksanaan Anda.
Beli atau selamatkan beberapa kayu bekas (atau kayu lapis tebal) dan buat sendiri tas jinjing bir 6 botol dari kayu yang kokoh dan sangat nyaman untuk mengangkut minuman beralkohol musim panas favorit itu dengan lebih aman dan bergaya. Tapi bukan itu saja: kami akan memasang pembuka botol di dalamnya sehingga Anda tidak akan pernah melupakan hal kecil penting ini di rumah.
Kepadamu akan dibutuhkan:
- panel pinus setebal 1,9-2 cm (pilih kayu sesuai selera Anda, pinus akan hidup paling lama dalam kondisi penggunaan kotak ini yang diharapkan);
- papan pinus 0,6-0,7 cm;
- pita pengukur;
- pin (pegangan pembawa masa depan) dengan diameter 1,9-2 cm;
— amplas 220 grit (pasir);
- mesin pemotong kayu atau alat wakil dan gergaji tangan;
- lem yang bagus untuk kayu;
- pistol paku parket (atau paku biasa dengan panjang yang dibutuhkan dan palu);
- paku parket 3,1-3,2 cm;
- paku parket 1,9-2 cm;
- noda;
— pembuka botol yang dipasang di dinding;
- sekrup 1,9-2 cm;
- benang nilon.
Kami memotong bagian-bagiannya dan merakit kotak pembawa
1. Tandai detailnya menggunakan pensil, penggaris, dan pita pengukur. Menggunakan gergaji potong atau gergaji tangan, dapatkan bagian-bagian berikut (dimensi diberikan dalam konversi yang tepat dari inci, jadi sebelum menandai dan menggergaji bagian-bagian tersebut, ada baiknya menyesuaikan dimensi menjadi tepat - bulat - sentimeter dengan kompatibilitas penuh ukuran satu sama lain):
— A (2 buah): 0,635x6.35x15.24 cm;
— B (1 buah): 0,635x6.35x22.86 cm;
— C (1 buah): 1,905x24,13 cm;
— D (4 buah): 0,635x3.175x26.67 cm;
— E (2 buah): 0,635x6.35x26.67 cm;
— F (1 buah): 1.905x15.24x22.86 cm;
— G (2 buah): 1.905x15.24x30.48 cm.
2. Ambil 2 buah potongan “G” dan beri tanda pada sisinya (kanan dan kiri) masing-masing dengan jarak 17,78 cm dari bawah. Kemudian kiri dan kanan 2,8575 cm dari tengah tepi atas papan.
3. Hubungkan tanda samping dan atas di kanan dan kiri pada masing-masing bagian hingga diperoleh sudut optimal mempersempit sisi laci ke arah pegangan.
4. Siapkan mesin atau ambil saja gergaji dan potong sudut-sudut berlebih sesuai dengan tandanya.
5. Buat potongan berukuran sedang di bagian tengah kedua potongan “A”. Kemudian buat 2 buah potongan di tengah pada bagian “B” dengan jarak 7,62 cm dari samping, kemudian pada tanda 15,24 cm, lebar potongan kira-kira sama dengan tebal bagian tersebut. Bagian-bagian ini akan membentuk “kisi” yang akan menampung dan memisahkan botol-botol di dalam kotak.
7. Dengan menggunakan mata bor berdiameter 1,905 cm, buat lubang di tengahnya 2,54 cm dari atas setiap potongan “G”. Berhati-hatilah dan bor hanya sedalam sekitar 1,27 cm dan jangan sampai seluruhnya - di sinilah pegangan tas bir akan dipasang.
8. Oleskan sedikit lem ke tepi bawah bagian dalam potongan pertama “G” dan rekatkan potongan “F” (yaitu dasar laci) ke tepi ini dan kencangkan di tempatnya dengan parket tambahan sepanjang 3,1 paku (atau biasa) 3,2 cm.
9. Oleskan sedikit lem ke ujungnya dan masukkan, rekatkan, peniti (pegangan masa depan) dengan diameter 1,9-2 cm ke dalam lubang yang dibor di sisi kotak.
10. Oleskan lem dalam jumlah yang sama ke tepi pin yang berlawanan. Oleskan lem ke sisi dasar laci. Rekatkan pin dan alasnya ke bagian dalam potongan "G" kedua. Jangan lupa kencangkan alasnya pada sisi kedua dengan paku.
11. Oleskan lem pada sambungan dan dasar “kisi” bagian “A” dan “B”. Rekatkan kisi-kisi ke alasnya, sejajarkan dengan sangat tepat.
12. Ambil salah satu potongan “D” dan sekali lagi, dengan menggunakan sedikit lem di kanan dan kiri, tempelkan potongan di bagian bawah di antara sisi laci. Selain itu amankan dengan paku. Ulangi di sisi lain.
13. Dengan menggunakan pita pengukur dan pensil, tandai sisi potongan “E” dan “D” dengan jarak 1,905 cm. Rekatkan bagian-bagiannya dan kencangkan dengan paku sepanjang 1,9-2 cm, ulangi pada sisi lainnya.
14. Amplas area yang tidak rata atau kasar pada laci dengan amplas 220 grit.
Perakitan kotak pembawa bir selesai!
Dekorasi
1. Lap laci hingga bersih dengan iklanamp kain bersih. Biarkan kayu mengering dan pilih pewarna atau pelapis lain pilihan Anda.
2. Oleskan pewarna secara merata, ikuti petunjuk pada kaleng. Pastikan untuk melapisi seluruh permukaan dan bagian dalam wadah.
3. Dengan menggunakan sekrup sadap sendiri, pasang pembuka botol ke laci.
4. Ambil benang nilon dan mulailah membungkus pegangan laci dengan hati-hati. Ini opsional, tetapi merupakan tambahan yang sangat berharga. Kerjakan dari tengah ke kanan, lalu kembali ke kiri dan lagi ke kiri, lalu kembali ke tengah. Terakhir, ikat benang dengan erat beberapa kali.
Buatlah kotak seperti ini untuk teman. Bereksperimenlah dengan hasil akhir dan pernis yang berbeda: pada foto di sebelah kiri, noda membuat kayu tampak terbakar dan kasar. Anda dapat menggunakan bagian-bagian dengan warna kontras untuk laci.
Liburan bulan Mei sudah dekat, dan banyak yang berencana untuk keluar ke alam. Apa jadinya alam tanpa barbekyu dan bir? Botol sangat tidak nyaman untuk diangkut, tentu saja, jika Anda tidak membelinya dalam kotak. Jika Anda perlu membawa beberapa botol bir atau limun di angkutan umum atau membawanya saat piknik, Anda dapat menggunakan wadah khusus. Dalam wadah botol seperti itu, minuman tidak akan terguncang dan botol-botol tidak akan pecah satu sama lain.
Pada artikel ini kami akan memberi tahu Anda cara membuat wadah botol bir dengan tangan Anda sendiri.
Bahan untuk membuat gendongan :
- templat bagian (ditunjukkan di bawah)
- papan kayu tebal 20 mm
- kayu lapis laminasi tebal 3 mm
- tiang kayu, diameter 25 mm, panjang sekitar 230 mm
- noda
- lem kayu
Alat untuk membuat pembawa:
- stapler konstruksi atau palu dan paku kecil
- gergaji ukir, gergaji besi atau gergaji bundar
- mengebor
- mengajukan
- ampelas
Membuat wadah botol bir
Tandai bagian bawah papan dengan dua bagian yang serupa talenan, mereka akan menjadi elemen akhir dari pembawa. Pada kayu lapis laminasi, Anda perlu menandai 2 strip samping lebar, 2 strip samping sempit, 2 partisi melintang, 1 partisi memanjang.
Dengan menggunakan gergaji ukir atau gergaji lainnya, potong bagian yang sudah ditandai.
Bor lubang dengan diameter 25 mm di dinding ujung. Lubang-lubang ini diperlukan untuk memasang pegangan.
Nasihat: agar lubang-lubangnya berada pada sumbu yang sama, bor dulu satu bagian, lalu pasang bagian kedua dan bor.
Dengan menggunakan file, proses bagian tepi dan tepinya, bulatkan sedikit. Untuk membuat pinggirannya lebih halus, gunakan amplas.
Rawat bagian-bagian tersebut dengan noda dan biarkan lapisannya mengering.
Tempatkan bagian depan dan dinding belakang dekat dengan ujung bawah. Amankan bagian-bagiannya menggunakan stapler atau paku.
Pasang strip samping lebar di bagian samping; strip tersebut harus menutupi tepi samping bagian bawah.
Kemudian kencangkan potongan kayu lapis samping yang sempit. Tingginya harus sekitar 12 cm dari strip bawah.
Gergaji tiang kayu sesuai panjang yang diinginkan. Lumasi pinggirannya dengan lem dan masukkan ke dalam lubang yang dibor di bagian atas ujungnya. Hapus sisa lem dan biarkan mengering.
Hubungkan partisi memanjang dan dua partisi melintang. Melakukan pemotongan di tempat yang tepat akan membantu Anda dalam hal ini.
Masukkan partisi ke dalam, jika timbul kesulitan, Anda dapat mengampelas tepi partisi dengan amplas.
Pembawa botol bir sudah siap. Sekarang Anda bisa pergi piknik dengan aman.
Templat
- ketebalan 3 mm
- panjang 130 mm, tinggi 90 mm
Partisi memanjang:
- ketebalan 3 mm
- panjang 180 mm, tinggi 90 mm
- kedalaman pemotongan 45 mm, lebar pemotongan 3 mm
- jarak antar potongan 60 mm
Dasar:
- ketebalan 20mm
- panjang 180 mm, lebar 130 mm
Garis samping sempit:
- ketebalan 3 mm
- panjang 220 mm, tinggi 40 mm
Lebar botol bir setengah liter pada umumnya adalah 70mm. Berdasarkan fakta bahwa kita akan menempatkan botol dalam dua baris, mengambil papan dengan lebar kurang dari 180mm untuk kotaknya cukup berisiko. Dalam kasus saya, bagian struktur yang menahan beban, yaitu dinding samping, terbuat dari papan kayu ek dengan lebar 190mm. Saya menyesuaikan semuanya dengan ukuran ini.
Desain baki mengasumsikan adanya tiga elemen utama - bagian bawah, slot untuk botol, dan pegangan. Untuk membuat dua papan pertama, kita membutuhkan 3 papan dengan lebar 190mm, tebal sekitar 10mm, dan panjang minimal 390mm.
Cara termudah untuk menandai lubang botol adalah dengan menggunakan sampel - lingkaran, dalam kasus saya dipotong dari papan serat. Saya memotong lingkaran dengan diameter 80mm agar slotnya lebih serbaguna. Saat menandai, kita harus ingat bahwa kita perlu menyisakan margin di sepanjang tepinya agar menyatu dengan dinding samping, dan jarak antara slot apa pun tidak boleh kurang dari 20mm, jika tidak, kisi yang dihasilkan akan terlalu rapuh. Tidak perlu membuat sekat lebar antar semua botol, misalnya saya sisakan yang melintang saja, tidak ada yang membujur.
Cara termudah untuk membuat lubang pada papan adalah dengan gergaji ukir, namun ini sudah cukup untuk pemotongan lain di artikel ini. Pada lekukan yang tersisa di sepanjang tepinya, kami menandai segmen 50mm, dan memotong semua yang ada di antaranya.
Jika slot horizontal harus dibuat dari satu papan atau papan, maka bagian bawahnya dapat dibuat dari dua hingga empat papan dengan lebar total 190 mm.
Mari beralih ke bagian samping. Tinggi botol bir sedikit kurang dari 300mm, jadi tinggi akhir kotak kita harusnya 350mm; dengan menurunkannya, kita berisiko mengalami masalah saat memakainya, karena tutup botol yang tajam akan mengenai tangan Anda. Jika Anda bukan seorang estetika seperti saya, tidak perlu memotong profil sedemikian rumitnya, Anda cukup memotong sudut-sudutnya, membuat bagian atasnya berbentuk trapesium.
Untuk memasang slot, kami membuat empat lubang di setiap dinding samping dengan kedalaman 50mm dan lebar sama dengan lebar papan tempat kami membuat slot, dalam kasus saya 10mm. Saya menempatkan slot pada ketinggian 50 dan 130mm dari tepi bawah.
Saya membuat pegangan dan sisi-sisinya dari kayu ek setebal 20mm - bahan yang kuat dan tahan lama, tetapi sayangnya sangat berat, Anda tidak boleh menyalahgunakannya saat membuat kotak dan sejenisnya.
Bentuk pegangannya bisa berubah-ubah, yang utama adalah area yang masuk ke dinding samping berbentuk persegi panjang, memiliki tinggi yang sama dan “hidup” pada garis yang sama. Untuk memasang pembuka di laci, saya membuat pegangannya menonjol dan mengebor beberapa lubang dengan diameter yang diperlukan di dalamnya.
Pembukanya sendiri adalah sepasang bagian pipa 20mm, dengan slot yang sedikit dimodifikasi dengan file. Mengingat bahwa dengan bantuan penggiling sudut hal ini dapat dilakukan dalam waktu kurang dari lima menit, ide ini mungkin bisa disebut yang paling sederhana dari semua yang mungkin ada. Pembuka dihubungkan ke pegangan menggunakan sekrup sadap sendiri.
Untuk menghubungkan pegangan dengan sisa struktur, kami membuat lubang persegi panjang di papan samping, lebar 20 mm dan tinggi 45 mm. Dengan menggunakan bor, gergaji ukir, dan pahat tajam, tidak akan sulit untuk mengatasinya. tugas ini.
Untuk memberikan kesan pub vintage pada produk, saya melapisi bagian-bagiannya dengan noda warna berbeda dan kemudian mengampelasnya, menghilangkan lapisan atas di beberapa tempat.
Menyatukan konstitusi. Kami kencangkan bagian bawah menggunakan sekrup sadap sendiri, dan kencangkan semua bagian lainnya dengan paku, setelah sebelumnya mengebor lubang agar tidak membelah tepi bagian.
Setelah berkumpul, kami membuka nampan dengan pernis dan pergi ke teman kami untuk minum bir dingin.