Projektimi dhe instalimi i saktë i tubacioneve të kanalizimeve është shumë i rëndësishëm për funksionimin e mëtejshëm, dhe për këtë arsye të gjitha fazat e punës duhet të kryhen në përputhje me dokumentet rregullatore.
Kanalizimet e jashtme përfshijnë të gjithë tubacionet kryesore të vendosura jashtë ndërtesave, duke përfshirë puset e kullimit dhe kanalizimeve, si dhe pajisjet e tjera të nevojshme për funksionimin e duhur të të gjithë sistemit.
Kanalizimet e jashtme mund të kenë disa sisteme instalimi:
- një sistem i përgjithshëm aliazh, në të cilin rrjedhjet e brendshme dhe të shiut kombinohen në një rrjet kanalizimesh, duke përfshirë një kolektor;
- sistem aliazh gjysmë të ndarë– ujërat e zeza nga aktivitetet sociale dhe ekonomike dhe ujërat e zeza nga reshjet atmosferike kanë një sistem të veçantë, por shkarkimi ndodh në një kanalizim;
- sistem aliazh i ndarë– çdo sistem kullon ujërat e zeza në një kolektor të veçantë.
Meqenëse ujërat e zeza në shumicën e sistemeve të kanalizimeve shkarkohen sipas parimit të gravitetit, gjatë hartimit të një skeme dhe plani pune, vëmendje e veçantë i kushtohet terrenit.
Instalimi i tubacionit duhet të kryhet në përputhje me SNiP "2.04.03-85", me llogaritje të saktë të pjerrësisë.
Kjo për faktin se duke ulur ose rritur këndin e prirjes së tubave, më pas mund të bllokoni linjën e kanalizimeve me fraksione të ngurta, përkatësisht:
- vendosja e tubave me një pjerrësi të lehtë do të çojë në kullim të dobët, si rezultat i së cilës grimcat e ngurta do të vendosen në tuba, me formimin e mëtejshëm të bllokimeve;
- vendosja e tubave me një pjerrësi të madhe nuk do të lejojë që uji të thithë trupat e ngurtë për shkak të shpejtësisë së lartë të rrjedhjes.
Besohet se shpejtësia optimale e ujit në tubacionin e kanalizimeve duhet të jetë në intervalin 0.7-1 m/s.
Në këtë drejtim, dokumentet rregullatore kanë vendosur vlera optimale dhe, në varësi të diametrit të tubit, ato variojnë nga 0.8 në 2 cm/m.p.
Në veçanti, për tubat me diametër 110 mm pjerrësia duhet të jetë jo më e vogël 2 cm/m.p., dhe për tubat me diametër 160 mm – 0,8 cm/m.p. Kur instaloni një linjë kanalizimesh, një pjerrësi e kundërt nuk lejohet.
E rëndësishme! Kur shtroni sistemi i jashtëm tubacionet e kanalizimeve dhe komponentët e bërë nga materiale cilësore, dhe në përputhje me të gjitha standardet sanitare.
Për shkak të faktit se ujërat e zeza kanë një përbërje agresive, edhe një defekt i vogël në tubacionin e kanalizimeve mund të çojë në pasoja të pakëndshme.
Video: vendosja e tubacioneve të kanalizimeve
Shumica e rrjeteve të jashtme të kanalizimeve janë instaluar nga gypat e polivinilklorurit (PVC): gize, çelik, polipropileni, asbest-çimento, beton arme, etj.
Para instalimit, tubat metalikë duhet të trajtohen me materiale që parandalojnë korrozionin (SNiP "3.04.03-85" "2.03.11-85").
Foto: tuba metalikë
Aktualisht, ka një përhapje të gjerë tuba të valëzuar bërë nga polietileni.
Falë tuaj vetitë fizike, ky lloj tubi mund të përballojë presionin e lartë të tokës, dhe ka një sipërfaqe të brendshme të lëmuar që parandalon bllokimet.
Foto: tuba të valëzuar
Video: instalimi i rrjeteve të jashtme të kanalizimeve
Thellësia e shtrimit
Thellësia e kanalit në të cilin do të vendoset linja e kanalizimit varet nga shumë faktorë, veçanërisht nga lloji i tokës, ngarkesa në të gjithë zonën e shtrimit të tubacionit dhe kushtet klimatike Rajon.
Të gjitha gërmimi në lidhje me gërmimin e një kanali dhe përgatitjen e tij për vendosjen e një linje kanalizimesh duhet të kryhet në përputhje me kërkesat SNiP (3.02.01-87).
Foto: thellësia e kanalit
Thellësia e kanalit llogaritet në bazë të kushteve klimatike të rajonit të caktuar, por jo më pak 0.7 m nga sipërfaqja në skajin e tubit.
Pra, për rajonet veriore të Rusisë, thellësia nga sipërfaqja e tokës deri në skajin e sipërm të tubit duhet të jetë brenda 3-3,5 m., Për zona e mesme dhe jugu i Rusisë - 2,5-3m dhe 1,25-1,5m përkatësisht.
E rëndësishme! Vëmendje e veçantë Vlen t'i kushtohet vëmendje afërsisë së ujërave nëntokësore dhe terrenit. Nëse për ndonjë arsye nuk është e mundur të ulni të gjithë ose një pjesë të linjës së kanalizimit në thellësinë e kërkuar, ajo izolohet me material izolues të nxehtësisë për ta mbrojtur atë nga ngrirja.
Foto: izolim me material termoizolues
Nëse tubacioni kalon nën një zonë ku ka një ngarkesë mekanike në tokë, tubi "fshihet" në një rast.
Foto: bori në një kuti
Diagrami i rastit:
- kapëse;
- pranga;
- ngjitës;
- ngjitës kundër korrozionit;
- rast;
- unaza mbështetëse;
- tub.
Hendeku duhet të hapet në përputhje me projektin e trasesë dhe gjerësia e saj duhet të jetë afërsisht 60 cm(për tubat me diametër 110 mm), dhe thellësia është disa centimetra më shumë se sa pritej (ia vlen të merret parasysh jastëku i rërës).
Për tubat me diametër më të madh, gjerësia e kanalit bëhet e tillë që distanca nga muret e kanalit në tub të jetë rreth 20 cm, dhe për gypat me diametër që tejkalon 225 mm, distanca tub-mur duhet të jetë së paku 35 cm.
Kjo është bërë me qëllim të hyrjes së lirë në linjën e kanalizimit gjatë punës së instalimit.
Nëse përgjatë rrugës së kanalizimit ka ndryshime në terren (ndryshime) ose kanali ndryshon drejtimin, atëherë në këto vende vendosen puse.
Foto: bie mirëPuset duhet të instalohen gjithashtu nëse gjatësia e vijës së drejtë i kalon 25 metra. Hendeku është gërmuar deri në pikën e lidhjes me kanalizimin qendror ose gropën septike.
Baza e kanalit pastrohet, nivelohet dhe mbushet me rërë: kjo formon një jastëk për tubacionin e ardhshëm, dhe shtresa e rërës nivelohet me një pjerrësi të lehtë në drejtim të kullimit.
Instalimi
Instalimi i linjës së jashtme të kanalizimeve fillon nga ndërtesa në drejtim të kullimit.
I gjithë procesi i instalimit zhvillohet në përputhje me planin e gjurmës dhe, duke marrë parasysh këto të dhëna, i gjithë diagrami i tubacionit transferohet në zonë, me shtylla të instaluara në qendër të puseve të propozuara dhe shënohet boshti i kanalizimit. me një fije të shtrirë. Tubat e kanalizimeve vendosen në fund të kanalit me një bazë të përgatitur në formën e një jastëku rere.
Për të parandaluar mbajtjen e grimcave të ngurta në fuga, tubat vendosen me prizën lart, drejt bashkimit të rrjetit të brendshëm të kanalizimeve ose, më thjesht, lart në pjerrësi. (SNiP "3.05.04-85", 3.4).
Puna në instalimin e tubave të kanalizimeve duhet të kryhet në një temperaturë ajri prej të paktën -10 ° C, ndërsa vulat e gomës rekomandohet të ruhen në një vend të ngrohtë dhe të instalohen në tuba menjëherë para instalimit.
Foto: instalimi i vulës
Nuk lejohet instalimi i tubave të kanalizimeve nga materiale të ndryshme.
E rëndësishme! Para shtrimit, të gjitha tubat kontrollohen për defekte, pastrohen nga ndotja dhe vendosen përgjatë hendekut.
Instalimi i linjës së kanalizimit kryhet direkt në kanal. Në prizë është instaluar një unazë O dhe për të lehtësuar instalimin, mbyllja dhe pjesa e lëmuar e tubit të futur trajtohen me lubrifikant (tuba PVC).
Gjatë instalimit të kanalizimeve nga tubat prej gize, hendeku midis tubit dhe prizës pritet duke përdorur një ngjitës.
Kjo mund të jetë kërp ose fije e bituminizuar (në varësi të GOST-it të tubit të përdorur). Thellësia e stampimit varet nga diametri i tubit, për shembull, për tubat me diametër deri në 200 mm, thellësia e ngulitjes së bashkimit do të jetë 35 mm (SNiP "3.05.04-85" 3.44).
Foto: thellësia e bashkimit
Nëse, kur vendosni një sistem kanalizimi, është e nevojshme të ndryshoni drejtimin e rrugës, atëherë në këto vende instalohen puse.
Drejtimi i tubit nuk duhet të lejohet të rrotullohet më pak se 90°. I gjithë rrjeti i kanalizimeve është instaluar në linjën kryesore qendrore ose në një gropë septike autonome. Në këtë rast, duhet të kontrolloni vazhdimisht pjerrësinë me një nivel.
E rëndësishme! Gjatë instalimit të kanalizimeve nga Tuba PVC Këshillohet që midis bazës së folesë dhe pjesës fundore të tubit të lidhur të lihet një boshllëk prej afërsisht 1 cm, i ashtuquajturi "qepje termike".
Foto: rregullimi i hendekut
Pas instalimit, i gjithë vargu i montuar kontrollohet për rrjedhje dhe cilësinë e kullimit, dhe tubacionet e presionit testohen për rrjedhje nën presion, të udhëhequr nga kanalizimi me presion SNiP.
Pas të gjitha provave, tubat spërkaten me rërë, me përjashtim të nyjeve të prapanicës, dhe derdhen me ujë. Kjo bëhet për të kompaktuar jastëkun dhe për të shmangur formimin e zbrazëtirave nën tuba.
Natyrisht, në temperatura nën zero ky proces duhet të zëvendësohet me ngjeshje më të plotë. Pas ri-kontrollit të tubacionit për rrjedhje, në përputhje me standardet SNiP ("3.05.04-85" seksioni 7), ai mbulohet me tokë.
Rrjetet e brendshme të kanalizimeve
Të gjitha rrjetet e brendshme të kanalizimeve janë të pajisura në varësi të qëllimit të objektit dhe kërkesave për të për grumbullimin e ujërave të zeza dhe ujërave të zeza atmosferike. (SNiP "2.04.01-85" 15.1).
Kanalizimet e brendshme përfshijnë disa sisteme:
- amvisëri– projektuar për kullimin e ujërave të zeza nga mbeturinat shtëpiake pajisje hidraulike(tualet, vaskë, lavaman, Makinë larëse etj.);
- kullimet e brendshme– qëllimi i sistemit është të kullojë shkrirjen dhe ujërat e shiut nga çatia e një ndërtese;
- të bashkuar– Mbetjet industriale dhe shtëpiake kombinohen në një rrjet kanalizimesh për qëllime të depozitimit dhe trajtimit të përbashkët të tyre;
- prodhimit– largimi i ujërave të zeza të krijuara si rezultat i aktiviteteve të ndërmarrjes.
Këshillohet që të planifikoni të gjithë sistemin e brendshëm të kanalizimit në fazën e projektimit të shtëpisë, në mënyrë që të mos ketë probleme me rizhvillimin në të ardhmen.
Elementi kryesor në sistemin e brendshëm të ujërave të zeza është ngritësi, në të cilin të gjitha daljet nga kuzhina, banjo, dhomë tualeti etj.
Është më mirë të instaloni ngritësin qendror në një kabinet të veçantë vertikal të tipit bosht (për shtëpitë me dy ose më shumë kate).
Foto: boner
Pjesa e poshtme e tubacionit çohet në bodrum, pjesa e sipërme në papafingo dhe më pas përmes çatisë.
Lartësia mbi nivelin e çatisë duhet të jetë 0,5 m - për çati e ngritur, dhe 0,3 m – për çati të sheshtë. I gjithë dega është montuar nga tubat PVC me vendosjen e kthesave në vendet ku supozohet të vendosen pajisjet hidraulike.
Nëse planifikoni të keni dy banja ose banjo, atëherë instalohet një ngritës i veçantë për secilën. Ngritësi qendror është montuar më afër tualetit, pasi kjo është më shpesh zona më e bllokuar.
Tubi i kullimit për tualetin bëhet sa më i shkurtër dhe vendoset në një mallë (nëse është e mundur). Pjesa tjetër e pajisjeve është e lidhur me tubat e daljes të fshehura në mur ose të vendosura në sipërfaqe.
Foto: lidhje tualeti
Për kanalizimet e brendshme, tubacionet me diametër prej 110 mm- Ky është ngritësi qendror. Për linjat e degëve, tuba me diametër prej 50 mm.
Shpatet e tubave të daljes duhet të bëhen në përputhje me SNiP për kanalizimet e gravitetit:
- për tuba me diametër nga 85 në 100 mm - 0,02 (2 cm për m/n);
- >për tuba me diametër 40 deri në 50 mm - 0,03 (3 cm për m/p).
Foto: shpatet e tubave
Për të pastruar tubacionet në rast bllokimi, instalohet një inspektim në ngritësin qendror, duke zgjedhur vendin më të aksesueshëm.
Inspektimi kërkohet gjithashtu të instalohet në vendet ku të gjithë ngritësit janë të kombinuar në një linjë të përbashkët kryesore, përpara se të bashkohet me tubin e daljes së tubacionit të jashtëm.
Foto: shkëputja e tubave të kanalizimeve
Video: vendosja e tubave të brendshëm të kanalizimeve
Territori i siguruar
Zona e mbrojtjes së kanalizimeve përfshin të gjithë sistemin e largimit të ujërave të zeza, duke përfshirë puset dhe impiantet e trajtimit, si dhe territorin përreth këtyre objekteve.
Sipas dokumenteve rregullatore (SNiP "2.04.03-85"), zona e sigurisë nuk duhet të jetë më e vogël se 5 m nga vendndodhja tub kanalizimesh.
Ky tregues është i zbatueshëm si për kanalizimet me gravitet ashtu edhe për sistemet e shkarkimit të ujërave të zeza nën presion.
Në rajonet me toka të paqëndrueshme dhe të dobëta, si dhe në zonat me aktivitet sizmik, zona e mbrojtjes mund të rritet.
Në zonën e sigurisë së kanalizimeve është e ndaluar:
- të kryejë çdo punë ndërtimi, gërmimi dhe shpërthimi;
- magazinimi i materialeve;
- mbillni pemë dhe shkurre (në varësi të thellësisë së tubacionit);
- bllok qasjesh ndaj rrjeteve dhe strukturave të kanalizimeve.
Foto: Puna e gërmimit është e ndaluar
E rëndësishme! Nuk rekomandohet vendosja e parkimit për automjetet pranë zonës së sigurisë së rrjeteve të kanalizimeve, si dhe kryerja e punëve që lidhen me presion të shtuar në tokë.
Nëse është e nevojshme të kryhet puna e mësipërme, duhet të bihet dakord me autoritetet lokale.
Kur punoni për vendosjen e një rrjeti uji pranë një tubacioni të kanalizimeve, duhet të udhëhiqeni nga dokumentet rregullatore (SNiP "2.04.02-84"), të cilat rregullojnë metodat e punës dhe zonat sanitare.
Në sektorin privat, është zakon që furnizimi me ujë të vendoset në një distancë prej më shumë se 40 cm nga tubi i kanalizimit, me kusht që linja e furnizimit me ujë të jetë dukshëm më e lartë se linja e kanalizimit.
Gjatë rregullimit të kanalizimeve si private ashtu edhe brenda ndërtesë apartamentesh Duhet të ndiqni rregullat dhe rregulloret dhe të përdorni materialet e rekomanduara për këtë lloj pune.
Cilësia e instalimit dhe shtrimit të rrjetit të kanalizimeve përcakton funksionimin e duhur dhe afatgjatë shërbimet.
SNiP 3.05.04-85*
RREGULLAT E NDËRTIMIT
RRJETET DHE STRUKTURAT E JASHTME
UJËSJELLËS KANALIZIME
Data e prezantimit 1986-07-01
ZHVILLUAR NGA Instituti i Kërkimeve VODGEO i Komitetit Shtetëror të Ndërtimit të BRSS (Kandidati i Shkencave Teknike V.I. Gotovtsev - drejtuesi i temës, V.K. Andriadi), me pjesëmarrjen e Soyuzvodokanalproekt të Komitetit Shtetëror të Ndërtimit të BRSS (P.G. Vasilyev dhe A.S.Dondustrialh.I.), Projekti i Komitetit Shtetëror të Ndërtimit të BRSS (S.A. Svetnitsky), NIIOSP im. N.M. Gersevanov i Komitetit Shtetëror të Ndërtimit të BRSS (Kandidati i Shkencave Teknike V.G. Galitsky dhe D.I. Fedorovich), Giprorechtrans i Ministrisë së Flotës Lumore të RSFSR (M.N. Domanevsky), Instituti Kërkimor i Furnizimit me Ujë Komunal dhe Pastrimin e Ujit të AKH me emrin. K.D. Pamfilov i Ministrisë së Strehimit dhe Shërbimeve Komunale të RSFSR (Doktor i Shkencave Teknike N.A. Lukinykh, Kandidat i Shkencave Teknike V.P. Krishtul), Instituti i Projektit të Ndërtimit Industrial Tula të Ministrisë së Ndërtimit të Rëndë të BRSS.
PARAQITUR NGA Instituti i Kërkimeve VODGEO i Komitetit Shtetëror të Ndërtimit të BRSS.
PËRGATITUR PËR MIRATIMIN NGA Glavtekhnormirovanie Gosstroy BRSS (N. A. Shishov).
Në vend të SNiP III-30-74 në lidhje me kërkesat për prodhimin dhe pranimin e punës për ndërtimin dhe rindërtimin e rrjeteve të jashtme dhe strukturave të furnizimit me ujë dhe kanalizimeve.
SNiP 3.05.04-85* është një ribotim i SNiP 3.05.04-85 me amendamentin nr. 1, miratuar me Dekret të Komitetit Shtetëror të Ndërtimit të BRSS, datë 25 maj 1990 nr. 51.
Ndryshimi u zhvillua nga Instituti i Kërkimeve VODGEO i Komitetit Shtetëror të Ndërtimit të BRSS dhe Pajisjet Inxhinierike TsNIIEP të Komitetit Shtetëror për Arkitekturën.
Seksionet, paragrafët, tabelat në të cilat janë bërë ndryshime janë shënuar me një yll.
Dakord me Drejtorinë Kryesore Sanitare dhe Epidemiologjike të Ministrisë së Shëndetësisë të BRSS me letrën e datës 10 nëntor 1984 nr. 121212/1600-14.
Këto rregulla zbatohen për ndërtimin e rrjeteve të reja, zgjerimin dhe rindërtimin e rrjeteve ekzistuese të jashtme** dhe strukturave të furnizimit me ujë dhe kanalizimeve. vendbanimet dhe objektet ekonomike kombëtare.
** Rrjetet e jashtme - në tekstin e mëposhtëm “tubacionet”.
1. DISPOZITA TË PËRGJITHSHME
1.1. Gjatë ndërtimit të tubacioneve të reja, zgjerimit dhe rindërtimit ekzistues dhe strukturave të furnizimit me ujë dhe kanalizimeve, përveç kërkesave të projekteve (projekteve të detajuara)** dhe këtyre rregullave, kërkesat e SNiP 3.01.01-85*, SNiP 3.01.03-84 , SNiP III-4- gjithashtu duhet të respektohen 80* dhe rregulla dhe rregullore të tjera, standarde dhe dokumente rregullatore të departamenteve të miratuara në përputhje me SNiP 1.01.02-83.
** Projekte (projekte pune) - në tekstin e mëposhtëm “projektet”.
1.2. Tubacionet e përfunduara dhe strukturat e furnizimit me ujë dhe kanalizimeve duhet të vihen në punë në përputhje me kërkesat e SNiP 3.01.04-87.
2. PUNËT E TOKËS
2.1. Puna e gërmimit dhe puna e themelimit gjatë ndërtimit të tubacioneve dhe strukturave të furnizimit me ujë dhe kanalizimeve duhet të kryhen në përputhje me kërkesat e SNiP 3.02.01-87.
3. INSTALIMI I GYSATAVE
Dispozitat e përgjithshme
3.1. Gjatë lëvizjes së tubave dhe pjesëve të montuara që kanë veshje kundër korrozionit, duhet të përdoren pincë të buta, peshqirë fleksibël dhe mjete të tjera për të parandaluar dëmtimin e këtyre veshjeve.
3.2. Gjatë vendosjes së tubacioneve të destinuara për furnizimin me ujë të pijshëm dhe shtëpiak, ujërat sipërfaqësore ose ujërat e zeza nuk duhet të lejohen të hyjnë në to. Përpara instalimit, tubat dhe pajisjet, pajisjet dhe njësitë e përfunduara duhet të inspektohen dhe pastrohen brenda dhe jashtë nga papastërtitë, bora, akulli, vajrat dhe objektet e huaja.
3.3. Instalimi i tubacioneve duhet të kryhet në përputhje me planin e punës dhe hartat teknologjike pas kontrollit të përputhshmërisë së dimensioneve të kanalit me projektimin, fiksimit të mureve, shenjave të poshtme dhe kur instalimi i sipërm- struktura mbështetëse. Rezultatet e inspektimit duhet të pasqyrohen në regjistrin e punës.
3.4. Tubat e tipit prizë të tubacioneve pa presion, si rregull, duhet të vendosen me prizën lart në pjerrësi.
3.5. Drejtësia e seksioneve të tubacioneve me rrjedhje të lirë midis puseve ngjitur të parashikuar nga projekti duhet të kontrollohet duke parë "deri në dritë" duke përdorur një pasqyrë para dhe pas mbushjes së kanalit. Kur shikoni një tubacion seksion i rrumbullakët Rrethi i dukshëm në pasqyrë duhet të ketë formën e duhur.
Devijimi i lejuar horizontal nga forma e rrethit duhet të jetë jo më shumë se 1/4 e diametrit të tubacionit, por jo më shumë se 50 mm në çdo drejtim. Devijimet nga forma e saktë vertikale e rrethit nuk lejohen.
3.6. Devijimet maksimale nga pozicioni i projektimit të akseve të tubacioneve nën presion nuk duhet të kalojnë ±100 mm në plan, shenjat e tabakave të tubacioneve me rrjedhje të lirë - ± 5 mm, dhe shenjat e majës së tubacioneve nën presion - ±30 mm, përveç nëse standardet e tjera justifikohen nga dizajni.
3.7. Vendosja e tubacioneve me presion përgjatë një kurbë të sheshtë pa përdorur pajisje lejohet për tubat me fole me nyje prapanicë në vula gome me një kënd rrotullimi në çdo bashkim jo më shumë se 2° për tuba me diametër nominal deri në 600 mm dhe jo më shumë se 1° për tuba me diametër nominal mbi 600 mm .
3.8. Gjatë instalimit të tubacioneve të ujësjellësit dhe kanalizimeve në kushte malore, përveç kërkesave të këtyre rregullave, zbatohen kërkesat e Seksionit. 9 SNiP III-42-80.
3.9. Kur vendosni tubacione në një seksion të drejtë të gjurmës, skajet e lidhura të tubave ngjitur duhet të përqendrohen në mënyrë që gjerësia e hendekut të prizës të jetë e njëjtë përgjatë gjithë perimetrit.
3.10. Skajet e tubave, si dhe vrimat në fllanxhat e mbylljes dhe valvulave të tjera, duhet të mbyllen me priza ose priza druri gjatë ndërprerjeve të instalimit.
3.11. Vula gome për instalimin e tubacioneve në temperaturat e ulëta ajri i jashtëm nuk lejohet të përdoret në gjendje të ngrirë.
3.12. Për të vulosur (vulosur) nyjet e pasme të tubacioneve, materialet mbyllëse dhe "mbyllëse", si dhe ngjitësit, duhet të përdoren sipas dizajnit.
3.13. Lidhjet me fllanxha të aksesorëve dhe pajisjeve duhet të instalohen në përputhje me kërkesat e mëposhtme:
lidhjet me fllanxha duhet të instalohen pingul me boshtin e tubit;
rrafshet e fllanxhave që lidhen duhet të jenë të sheshta, dadot e bulonave duhet të vendosen në njërën anë të lidhjes; Bulonat duhet të shtrëngohen në mënyrë të barabartë në një model kryq;
eliminimi i shtrembërimeve të fllanxhave duke instaluar guarnicione të pjerrëta ose bulonave shtrënguese nuk lejohet;
Lidhjet e saldimit ngjitur me lidhjen e fllanxhave duhet të kryhen vetëm pas shtrëngimit uniform të të gjitha bulonave në fllanxha.
3.14. Kur përdoret dheu për të ndërtuar një ndalesë, muri mbështetës i gropës duhet të ketë një strukturë dheu të paprekur.
3.15. Hendeku midis tubacionit dhe pjesës së parafabrikuar të stacioneve të betonit ose tullave duhet të mbushet fort përzierje betoni ose llaç çimentoje.
3.16. Mbrojtja e tubacioneve të çelikut dhe betonit të armuar nga korrozioni duhet të kryhet në përputhje me dizajnin dhe kërkesat e SNiP 3.04.03-85 dhe SNiP 2.03.11-85.
3.17. Tubacionet në ndërtim i nënshtrohen pranimit me hartimin e raporteve të inspektimit punë e fshehur sipas formularit të dhënë në SNiP 3.01.01-85* fazat dhe elementët e mëposhtëm të punës së fshehur: përgatitja e bazës për tubacionet, instalimi i ndalesave, madhësia e boshllëqeve dhe vulosja e nyjeve të prapanicës, instalimi i puseve dhe dhomave, anti- Mbrojtja nga korrozioni i tubacioneve, mbyllja e vendeve ku tubacionet kalojnë nëpër mure puset dhe dhomat, mbushja e tubacioneve me ngjeshje etj.
Tubacionet e çelikut
3.18. Metodat e saldimit, si dhe llojet, elementët strukturorë dhe madhësitë e nyjeve të salduara tuba çeliku Telat duhet të përputhen me kërkesat e GOST 16037-80.
3.19. Para montimit dhe saldimit të tubave, duhet t'i pastroni nga papastërtitë, të kontrolloni dimensionet gjeometrike të skajeve, të pastroni skajet dhe sipërfaqet ngjitur të brendshme dhe të jashtme të tubave me një shkëlqim metalik në një gjerësi prej të paktën 10 mm.
3.20. Në fund punë saldimi izolimi i jashtëm i tubave në nyjet e salduara duhet të rikthehet në përputhje me projektin.
3.21. Kur montoni nyjet e tubit pa një unazë mbështetëse, zhvendosja e skajeve nuk duhet të kalojë 20% të trashësisë së murit, por jo më shumë se 3 mm. Për nyjet e prapanicës të montuara dhe të salduara në unazën cilindrike të mbetur, zhvendosja e skajeve nga pjesa e brendshme e tubit nuk duhet të kalojë 1 mm.
3.22. Montimi i tubave me diametër mbi 100 mm, i bërë me një saldim gjatësor ose spirale, duhet të kryhet me një zhvendosje të shtresave të tubave ngjitur me të paktën 100 mm. Kur montoni një bashkim tubash në të cilin tegeli gjatësor ose spirale i fabrikës është ngjitur në të dyja anët, zhvendosja e këtyre shtresave nuk duhet të bëhet.
3.23. Lidhjet tërthore të salduara duhet të vendosen në një distancë prej jo më pak se:
0,2 m nga buza e strukturës mbështetëse të tubacionit;
0.3 m nga sipërfaqja e jashtme dhe e brendshme e dhomës ose sipërfaqja e strukturës mbyllëse përmes së cilës kalon tubacioni, si dhe nga buza e kasës.
3.24. Lidhja e skajeve të tubave të bashkuar dhe seksioneve të tubacioneve kur hendeku midis tyre është më i madh se vlera e lejuar duhet të bëhet duke futur një "spiral" me një gjatësi prej të paktën 200 mm.
3.25. Distanca midis shtresës rrethore të saldimit të tubacionit dhe tegelit të grykave të salduara në tubacion duhet të jetë së paku 100 mm.
3.26. Montimi i tubave për saldim duhet të kryhet duke përdorur centralizues; Lejohet të drejtoni gërvishtjet e lëmuara në skajet e tubave me një thellësi deri në 3.5% të diametrit të tubit dhe të rregulloni skajet duke përdorur fole, kushineta rul dhe mjete të tjera. Seksionet e tubave me gërvishtje që tejkalojnë 3,5% të diametrit të tubit ose që kanë çarje duhet të priten. Skajet e tubave me prerje ose anime me thellësi më shumë se 5 mm duhet të priten.
Kur aplikoni një saldim me rrënjë, ngjitjet duhet të treten plotësisht. Elektrodat ose teli i saldimit të përdorur për saldimin me ngjitje duhet të jenë të së njëjtës shkallë me atë të përdorur për saldimin e tegelit kryesor.
3.27. Salduesit lejohen të bashkojnë nyjet e tubacioneve të çelikut nëse kanë dokumente që i autorizojnë ata të kryejnë punë saldimi në përputhje me Rregullat për Certifikimin e Salduesve të miratuar nga Minierat Shtetërore dhe Mbikëqyrja Teknike e BRSS.
3.28. Përpara se të lejohet të punojë në lidhjet e saldimit të tubacioneve, çdo saldator duhet të saldojë një bashkim të miratuar në kushtet e prodhimit (në kantierin e ndërtimit) në rastet e mëposhtme:
nëse ai filloi të saldonte tubacionet për herë të parë ose kishte një ndërprerje në punë për më shumë se 6 muaj;
nëse saldimi i tubave kryhet nga klasa të reja çeliku, duke përdorur klasa të reja të materialeve të saldimit (elektroda, tela saldimi, flukse) ose duke përdorur lloje të reja të pajisjeve të saldimit.
Në gypat me diametër 529 mm ose më shumë, lejohet saldimi i gjysmës së bashkimit të lejuar.
Lidhja e lejuar i nënshtrohet:
inspektimi i jashtëm, gjatë të cilit saldimi duhet të plotësojë kërkesat e këtij seksioni dhe GOST 16037-80;
kontrolli radiografik në përputhje me kërkesat e GOST 7512-82;
provat mekanike të tërheqjes dhe lakimit në përputhje me GOST 6996-66.
Në rast të rezultateve jo të kënaqshme të kontrollit të një nyjeje të lejueshme, kryhet saldimi dhe ri-inspektimi i dy nyjeve të tjera të lejueshme. Nëse, gjatë inspektimit të përsëritur, merren rezultate të pakënaqshme në të paktën një nga nyjet, saldatori njihet se ka dështuar në testet dhe mund të lejohet të bashkojë tubacionin vetëm pas trajnimit shtesë dhe testeve të përsëritura.
3.29. Çdo saldator duhet të ketë një shenjë të caktuar për të. Saldatori është i detyruar të trokasë ose bashkojë shenjën në një distancë prej 30 - 50 mm nga bashkimi në anën e aksesueshme për inspektim.
3.30. Saldimi dhe saldimi me ngjitje të bashkimeve të tubave mund të kryhet në temperatura të jashtme deri në minus 50°C. Në këtë rast, puna e saldimit pa ngrohjen e nyjeve të salduara lejohet të kryhet:
në temperaturat e ajrit të jashtëm deri në minus 20°C - kur përdoren tuba prej çeliku të karbonit me përmbajtje karboni jo më shumë se 0,24% (pavarësisht nga trashësia e mureve të tubit), si dhe tuba prej çeliku me lidhje të ulët. trashësia e murit jo më shumë se 10 mm;
në temperaturat e ajrit të jashtëm deri në minus 10°C - kur përdoren tuba prej çeliku të karbonit me përmbajtje karboni mbi 0,24%, si dhe tuba prej çeliku me aliazh të ulët me trashësi muri mbi 10 mm.
Kur temperatura e ajrit të jashtëm është nën kufijtë e mësipërm, punimet e saldimit duhet të kryhen me ngrohje në kabina të posaçme, në të cilat temperatura e ajrit duhet të mbahet jo më e ulët se sa më sipër, ose të ngrohet në jashtë skajet e tubave të salduar për një gjatësi prej të paktën 200 mm deri në një temperaturë prej të paktën 200°C.
Pas përfundimit të saldimit, është e nevojshme të sigurohet një ulje graduale e temperaturës së nyjeve dhe zonave ngjitur të tubave duke i mbuluar ato pas saldimit me një peshqir asbesti ose një metodë tjetër.
3.31. Gjatë saldimit me shumë shtresa, çdo shtresë e tegelit duhet të pastrohet nga skorjet dhe spërkatjet metalike përpara se të aplikohet tegeli tjetër. Zonat e metalit të saldimit me pore, gropa dhe çarje duhet të shkurtohen deri në metalin bazë dhe krateret e saldimit duhet të saldohen.
3.32. Gjatë saldimit manual me hark elektrik, duhet të aplikohen shtresa individuale të tegelit në mënyrë që seksionet e tyre të mbylljes në shtresat ngjitur të mos përkojnë me njëra-tjetrën.
3.33. Kur kryeni punë saldimi jashtë gjatë reshjeve, vendet e saldimit duhet të mbrohen nga lagështia dhe era.
3.34. Gjatë monitorimit të cilësisë së nyjeve të salduara të tubacioneve të çelikut, duhet të bëhen sa vijon:
kontrolli operacional gjatë montimit dhe saldimit të tubacionit në përputhje me kërkesat e SNiP 3.01.01-85*;
kontrollimi i vazhdimësisë së nyjeve të salduara me identifikimin e defekteve të brendshme duke përdorur një nga metodat e provës jo-shkatërruese (fizike) - radiografike (rrezet x ose gamagrafike) sipas GOST 7512-82 ose tejzanor sipas GOST 14782-86.
Përdorimi i metodës tejzanor lejohet vetëm në kombinim me metodën radiografike, e cila duhet të testojë të paktën 10% të numrit total të nyjeve që i nënshtrohen kontrollit.
3.35. Gjatë kontrollit të cilësisë operacionale të nyjeve të salduara të tubacioneve të çelikut, duhet të kontrollohet përputhshmëria me standardet elementet strukturore dhe dimensionet e nyjeve të salduara, metoda e saldimit, cilësia e materialeve të saldimit, përgatitja e skajeve, madhësia e boshllëqeve, numri i ngjitjeve, si dhe shërbimi i pajisjeve të saldimit.
3.36. Të gjitha nyjet e salduara i nënshtrohen inspektimit të jashtëm. Në tubacionet me një diametër prej 1020 mm ose më shumë, nyjet e salduara të salduara pa një unazë mbështetëse i nënshtrohen inspektimit të jashtëm dhe matjes së dimensioneve nga jashtë dhe brenda tubit, në raste të tjera - vetëm nga jashtë. Para inspektimit, shtresa e saldimit dhe sipërfaqet ngjitur të tubit në një gjerësi prej të paktën 20 mm (në të dy anët e tegelit) duhet të pastrohen nga skorje, spërkatje e metalit të shkrirë, shkallë dhe ndotës të tjerë.
Cilësia e saldimit sipas rezultateve të inspektimit të jashtëm konsiderohet e kënaqshme nëse nuk gjenden sa vijon:
çarje në shtresën dhe zonën ngjitur;
devijimet nga dimensionet dhe forma e lejueshme e tegelit;
prerje, prerje midis rrotullave, varje, djegie, kratere dhe pore të pa salduara që dalin në sipërfaqe, mungesë depërtimi ose varje në rrënjën e tegelit (kur inspektohet nyja nga brenda tubit);
zhvendosjet e skajeve të tubave që tejkalojnë dimensionet e lejuara.
Lidhjet që nuk plotësojnë kërkesat e listuara i nënshtrohen korrigjimit ose heqjes dhe rikontrollit të cilësisë së tyre.
3.37. Cilësia e saldimeve kontrollohet me metoda fizike të kontrollit për tubacionet e furnizimit me ujë dhe kanalizimeve me një presion projektimi deri në 1 MPa (10 kgf/sq.cm) në një vëllim prej të paktën 2% (por jo më pak se një bashkim për secilin saldator); 1-2 MPa (10-20 kgf/sq.cm) - në një vëllim prej të paktën 5% (por të paktën dy nyje për çdo saldator); mbi 2 MPa (20 kgf/sq.cm) në një vëllim prej të paktën 10% (por jo më pak se tre nyje për çdo saldator).
3.38. Lidhjet e salduara për inspektim me metoda fizike zgjidhen në prani të një përfaqësuesi të klientit, i cili regjistron në regjistrin e punës informacionin për nyjet e përzgjedhura për inspektim (vendndodhja, shenja e saldatorit, etj.).
3.39. Metodat e kontrollit fizik duhet të zbatohen në 100% të nyjeve të salduara të tubacioneve të vendosura në seksionet e kalimeve nën dhe mbi shinat hekurudhore dhe tramvaj, përmes barrierave ujore, nën autostrada, në kanalizimet e qytetit për komunikime kur kombinohen me shërbime të tjera. Gjatësia e seksioneve të kontrolluara të tubacioneve në seksionet e tranzicionit duhet të jetë jo më pak se dimensionet e mëposhtme:
Për hekurudhat- distanca midis akseve të gjurmëve të jashtme dhe 40 m prej tyre në çdo drejtim;
për autostrada - gjerësia e argjinaturës në fund ose gërmimi në krye dhe 25 m larg tyre në çdo drejtim;
për pengesat ujore - brenda kufijve të kalimit nënujor të përcaktuar me seksion. 6 SNiP 2.05.06-85;
Për të tjerët komunikimet inxhinierike- gjerësia e strukturës që kalohet, duke përfshirë pajisjet e saj të kullimit, plus të paktën 4 m në çdo drejtim nga kufijtë ekstremë të strukturës që kapërcehet.
3.40. Saldimet duhet të refuzohen nëse, pas inspektimit me metoda të kontrollit fizik, zbulohen çarje, kratere të pa salduar, djegie, fistula dhe gjithashtu mungesë depërtimi në rrënjën e saldimit të bërë në unazën mbështetëse.
Kur kontrolloni saldimet duke përdorur metodën radiografike, si më poshtë konsiderohen defekte të pranueshme:
poret dhe përfshirjet, madhësitë e të cilave nuk e kalojnë maksimumin e lejuar sipas GOST 23055-78 për nyjet e salduara të klasës 7;
mungesa e depërtimit, konkavitetit dhe depërtimit të tepërt në rrënjën e një saldimi të bërë me saldim me hark elektrik pa unazë mbështetëse, lartësia (thellësia) e së cilës nuk kalon 10% të trashësisë nominale të murit dhe gjatësia totale është 1/3. të perimetrit të brendshëm të kyçit.
3.41. Nëse zbulohen defekte të papranueshme në saldime me metoda të kontrollit fizik, këto defekte duhet të eliminohen dhe cilësia e një numri të dyfishtë saldimesh duhet të rikontrollohet në krahasim me atë të specifikuar në pikën 3.37. Nëse zbulohen defekte të papranueshme gjatë ri-inspektimit, të gjitha nyjet e bëra nga ky saldator duhet të inspektohen.
3.42. Zonat e saldimit me defekte të papranueshme i nënshtrohen korrigjimit me kampionim lokal dhe saldim pasues (si rregull, pa mbingarkuar të gjithë bashkimin e salduar), nëse gjatësia totale e kampionimit pas heqjes së zonave me defekt nuk e kalon gjatësinë totale të specifikuar në GOST 23055-78 për klasën 7.
Korrigjimi i defekteve në nyje duhet të bëhet me saldim me hark.
Prerjet e poshtme duhet të korrigjohen duke vendosur rruaza fije jo më shumë se 2 - 3 mm të larta. Çarjet më pak se 50 mm shpohen në skajet, priten, pastrohen mirë dhe saldohen në disa shtresa.
3.43. Rezultatet e kontrollit të cilësisë së nyjeve të salduara të tubacioneve të çelikut duke përdorur metoda të kontrollit fizik duhet të dokumentohen në një raport (protokoll).
Tubacionet prej gize
3.44. Instalimi i tubave prej gize të prodhuara në përputhje me GOST 9583-75 duhet të kryhet me vulosjen e nyjeve të foleve me rrëshirë kërpi ose fije të bituminizuara dhe një bllokues asbest-çimentoje, ose vetëm me ngjitës, dhe tuba të prodhuar në përputhje me TU 14-3 -12 pranga gome 47-83 të furnizuara të kompletuara me tuba pa pajisje mbyllëse.
Përbërja e përzierjes së asbestit-çimentos për ndërtimin e bravës, si dhe ngjitësit, përcaktohet nga projekti.
3.45. Madhësia e hendekut midis sipërfaqes së shtytjes së prizës dhe fundit të tubit të lidhur (pavarësisht nga materiali i vulosjes së bashkimit) duhet të merret, mm: për tubat me diametër deri në 300 mm - 5, mbi 300 mm - 8-10.
3.46. Dimensionet e elementeve vulosëse të bashkimit të prapanicës së tubave nën presion prej gize duhet të korrespondojnë me vlerat e dhëna në tabelë. 1.
Tabela 1
Diametri nominal |
Thellësia e futjes, mm |
||
tuba Dy, mm |
kur përdorni fijet e kërpit |
kur instaloni një bllokues |
kur përdorni vetëm izolues |
Tubacionet asbest-çimento
3.47. Madhësia e hendekut midis skajeve të tubave të lidhur duhet të merret, mm: për tubat me diametër deri në 300 mm - 5, mbi 300 mm - 10.
3.48. Para fillimit të instalimit të tubacioneve, në skajet e tubave që lidhen, në varësi të gjatësisë së bashkimeve të përdorura, duhet të bëhen shenja që korrespondojnë me pozicionin fillestar të bashkimit përpara instalimit të bashkimit dhe pozicionin përfundimtar në bashkimin e montuar.
3.49. Lidhja e tubave të asbest-çimentos me pajisje ose tuba metalikë duhet të kryhet duke përdorur pajisje prej gize ose tuba të salduar prej çeliku dhe vula gome.
3.50. Pas përfundimit të instalimit të secilës nyje prapanicë, është e nevojshme të kontrolloni vendndodhjen e saktë të bashkimeve dhe vulave të gomës në to, si dhe shtrëngimin uniform të lidhjeve me fllanxha të lidhjeve prej gize.
Beton i armuar
dhe tubacionet e betonit
3.51. Duhet të merret madhësia e hendekut midis sipërfaqes së shtytjes së prizës dhe fundit të tubit të lidhur, mm:
për tuba presioni prej betoni të armuar me diametër deri në 1000 mm - 12-15, me një diametër mbi 1000 mm - 18-22;
për tubat me fole të betonit të armuar dhe betonit pa presion me diametër deri në 700 mm - 8-12, mbi 700 mm - 15-18;
për tubat e qepjes - jo më shumë se 25.
3.52. Lidhjet fundore të tubave të furnizuar pa unaza gome duhet të vulosen me rrëshirë kërpi ose fije të bituminizuara, ose fije të bituminizuara sizale me bravë të mbyllur me një përzierje asbest-çimentoje, si dhe me izolues polisulfid (tiokol). Thellësia e futjes është dhënë në tabelë. 2, në këtë rast, devijimet në thellësinë e futjes së fillesë dhe bllokimit nuk duhet të kalojnë ±5 mm.
Boshllëqet midis sipërfaqes së shtytjes së prizave dhe skajeve të tubave në tubacionet me diametër 1000 mm ose më shumë duhet të mbyllen nga brenda me llaç çimentoje. Nota e çimentos përcaktohet nga projekti.
Për tubacionet e kullimit, lejohet mbyllja e hendekut të punës në formë zile në thellësinë e plotë me llaç çimentoje të klasës B7.5, përveç nëse projekti parashikon kërkesa të tjera.
tabela 2
Thellësia e futjes, mm |
|||
Diametri nominal, mm |
kur instaloni një bllokues |
kur përdorni vetëm izolues |
|
3.53. Mbyllja e nyjeve prapanicë të tubave të betonit të përforcuar me rrjedhje të lirë dhe betonit me skaje të lëmuara duhet të kryhet në përputhje me projektin.
3.54. Lidhja e tubave të betonit të armuar dhe betonit me pajisje tubacioni dhe tuba metalikë duhet të kryhet duke përdorur futje çeliku ose pjesë lidhëse në formë betoni të përforcuar të bëra sipas projektit.
Tubacione të bëra nga tuba qeramike
3.55. Madhësia e hendekut midis skajeve të tubave qeramikë që vendosen (pavarësisht nga materiali i përdorur për mbylljen e nyjeve) duhet të merret, mm: për tubat me diametër deri në 300 mm - 5 - 7, për diametra më të mëdhenj - 8-10.
3.56. Lidhjet e pasme të tubacioneve të bëra nga tubacione qeramike duhet të mbyllen me fije kërpi ose sizale të bituminizuara, të ndjekura nga një bravë e bërë nga llaç çimentoje B7.5, mastikë asfalti (bitum) dhe ngjitës polisulfidi (tiokol), përveç rasteve kur parashikohen materiale të tjera në projekti. Përdorimi i mastikës së asfaltit lejohet kur temperatura e lëngut të mbeturinave të transportuara nuk është më shumë se 40°C dhe në mungesë të tretësve të bitumit në të.
Dimensionet kryesore të elementeve të bashkimit të prapanicës së tubave qeramikë duhet të korrespondojnë me vlerat e dhëna në tabelë. 3.
Tabela 3
Thellësia e futjes, mm |
|||
Diametri nominal, mm |
kur përdorni fijet e kërpit ose sizalit |
kur instaloni një bllokues |
kur përdorni vetëm izolues ose mastikë bitumi |
3.57. Mbyllja e tubave në muret e puseve dhe dhomave duhet të sigurojë ngushtësinë e lidhjeve dhe hidroizolimin e puseve në tokë të lagësht.
Tubacione të bëra nga tuba plastikë*
3.58. Lidhja e tubave të bërë nga polietileni me densitet të lartë (HDPE) dhe polietileni me densitet të ulët (LDPE) me njëri-tjetrin dhe me pajisje duhet të kryhet me një mjet të nxehtë duke përdorur metodën e saldimit me prapanicë ose prizë. Saldimi i tubave dhe pajisjeve të bëra nga polietileni lloje të ndryshme(HDPE dhe PVD) nuk lejohen.
3.59. Për saldimin duhet të përdoren instalime (pajisje) që sigurojnë mirëmbajtjen e parametrave teknologjikë në përputhje me OST 6-19-505-79 dhe dokumentacionin tjetër rregullator dhe teknik të miratuar në mënyrën e përcaktuar.
3.60. Salduesit lejohen të saldojnë tubacione të bëra nga LDPE dhe HDPE nëse kanë dokumente që i autorizojnë ata të kryejnë punë në saldimin e plastikës.
3.61. Saldimi i tubave të bërë nga LDPE dhe HDPE mund të kryhet në një temperaturë të ajrit të jashtëm prej të paktën minus 10°C. Në temperatura më të ulëta të jashtme, saldimi duhet të bëhet në dhoma të izoluara.
Gjatë kryerjes së punës së saldimit, vendi i saldimit duhet të mbrohet nga ekspozimi ndaj reshjeve dhe pluhurit.
3.62. Lidhja e tubave të klorurit të polivinilit (PVC) me njëri-tjetrin dhe me pajisje duhet të kryhet duke përdorur metodën e ngjitjes me fole (duke përdorur ngjitësin GIPC-127 në përputhje me TU 6-05-251-95-79) dhe duke përdorur pranga gome të furnizuara të plota. me tubacionet.
3.63. Lidhjet e ngjitura nuk duhet t'i nënshtrohen stresit mekanik për 15 minuta. Tubacionet me nyje ngjitëse nuk duhet t'i nënshtrohen testeve hidraulike brenda 24 orëve.
3.64. Puna e ngjitjes duhet të kryhet në një temperaturë të jashtme prej 5 deri në 35°C. Vendi i punës duhet të mbrohet nga ekspozimi ndaj reshjeve dhe pluhurit.
4. TRANZICIONET E TUBACIONIT NËPËRMJET NATYRORE
DHE PENGESAT ARTIFICIALE
4.1. Ndërtimi i kalimeve të tubacioneve nën presion për furnizimin me ujë dhe kanalizimet përmes barrierave ujore (lumenj, liqene, rezervuarë, kanale), tubacione nënujore të ujëmarrësve dhe daljeve të ujërave të zeza brenda shtratit të rezervuarëve, si dhe kalime nëntokësore nëpër përrenj, rrugë (rrugë dhe rrugë). hekurudhat, duke përfshirë linjat e metrosë dhe tramvajit ) dhe kalimet e qytetit duhet të kryhen nga organizata të specializuara në përputhje me kërkesat e SNiP 3.02.01-87, SNiP III-42-80 (seksioni 8) dhe këtij seksioni.
4.2. Metodat për vendosjen e kalimeve të tubacioneve përmes barrierave natyrore dhe artificiale përcaktohen nga projekti.
4.3. Vendosja e tubacioneve nëntokësore nën rrugë duhet të kryhet nën kontroll të vazhdueshëm të rilevimit dhe gjeodezisë organizimi i ndërtimit për respektimin e pozicioneve të planifikuara dhe në lartësi të rasteve dhe tubacioneve të parashikuara nga projekti.
4.4. Devijimet e boshtit të kafazeve mbrojtëse të kalimeve nga pozicioni i projektimit për tubacionet me rrjedhje të lirë të gravitetit nuk duhet të kalojnë:
vertikalisht - 0,6% e gjatësisë së kasës, me kusht që të sigurohet pjerrësia e projektimit;
horizontalisht - 1% e gjatësisë së rastit.
Për tubacionet nën presion, këto devijime nuk duhet të kalojnë përkatësisht 1 dhe 1.5% të gjatësisë së kasës.
5. STRUKTURAT E FURNIZIMIT DHE KANALIZIMEVE TË UJËSARËVE
Strukturat e marrjes së ujit sipërfaqësor
5.1. Ndërtimi i strukturave për marrjen e ujërave sipërfaqësore nga lumenjtë, liqenet, rezervuarët dhe kanalet, si rregull, duhet të kryhet nga organizata të specializuara ndërtimi dhe instalimi në përputhje me projektin.
5.2. Përpara se të ndërtohet bazamenti për marrjen e ujit të shtratit të lumenjve, duhet të kontrollohen boshtet e tyre të shtrirjes dhe shenjat e përkohshme të standardeve.
Puset e ujit
5.3. Në procesin e shpimit të puseve, të gjitha llojet e punës dhe treguesit kryesorë (depërtimi, diametri i mjetit të shpimit, fiksimi dhe heqja e tubave nga pusi, çimentimi, matjet e nivelit të ujit dhe operacionet e tjera) duhet të pasqyrohen në regjistrin e shpimit. Në këtë rast, është e nevojshme të shënohet emri i shkëmbinjve të kaluar, ngjyra, dendësia (forca), thyerja, përbërja granulometrike e shkëmbinjve, përmbajtja e ujit, prania dhe madhësia e "prizës" gjatë fundosjes së rërës së gjallë, e shfaqur dhe niveli i vendosur i ujit të të gjithë akuiferëve të hasur dhe thithja e lëngut shpëlarës. Niveli i ujit në puse gjatë shpimit duhet të matet përpara fillimit të çdo ndërrimi. Në puset që rrjedhin, nivelet e ujit duhet të maten duke zgjatur tubacionet ose duke matur presionin e ujit.
5.4. Gjatë procesit të shpimit, në varësi të seksionit aktual gjeologjik, lejohet që brenda akuiferit të përcaktuar nga projekti, organizata e shpimit të rregullojë thellësinë, diametrat dhe thellësinë e mbjelljes së kolonave teknike pa ndryshuar diametrin operacional të pusit dhe pa rritur koston e punës. Ndryshimet në dizajnin e pusit nuk duhet të përkeqësojnë gjendjen e tij sanitare dhe produktivitetin.
5.5. Kampionet duhet të merren një nga çdo shtresë shkëmbi, dhe nëse shtresa është homogjene, çdo 10 m.
Me marrëveshje me organizatën e projektimit, mostrat e shkëmbinjve nuk mund të merren nga të gjitha puset.
5.6. Izolimi i akuiferit të shfrytëzuar në një pus nga akuiferët e papërdorur duhet të kryhet duke përdorur metodën e shpimit:
rrotulluese - me çimentim unazore dhe ndërtubulare të kolonave të shtresës së jashtme në shenjat e parashikuara nga projekti;
ndikim - duke shtypur dhe futur shtresën e jashtme në një shtresë balte të dendur natyrale në një thellësi prej të paktën 1 m ose duke kryer çimentim nën këpucë duke krijuar një shpellë me një zgjerues ose një grimë ekscentrike.
5.7. Për të siguruar përbërjen granulometrike të materialit për mbushjen e filtrave të puseve siç specifikohet në projekt, fraksionet e argjilës dhe rërës së imët duhet të hiqen me larje dhe para mbushjes, materiali i larë duhet të dezinfektohet.
5.8. Ekspozimi i filtrit gjatë mbushjes së tij duhet të kryhet duke ngritur kolonën e shtresës së jashtme çdo herë me 0,5 - 0,6 m pas mbushjes së pusit me 0,8 - 1 m lartësi. Kufiri i sipërm i spërkatjes duhet të jetë së paku 5 m mbi pjesën e punës të filtrit.
5.9. Pas përfundimit të shpimit dhe instalimit të një filtri, puset e marrjes së ujit duhet të testohen me pompim, të kryera vazhdimisht për kohën e përcaktuar nga projekti.
Para se të fillojë pompimi, pusi duhet të pastrohet nga llumi dhe të pompohet, si rregull, me një ngritje ajrore. Në akuiferët shkëmborë të thyer dhe zhavorr-zhavorr, pompimi duhet të fillojë nga rënia maksimale e projektimit në nivelin e ujit, dhe në shkëmbinjtë me rërë - nga rënia minimale e projektimit. Vlera e uljes minimale aktuale të nivelit të ujit duhet të jetë brenda 0.4 - 0.6 të asaj maksimale aktuale.
Në rast të ndalimit të detyruar të punës së pompimit të ujit, nëse koha totale e ndalimit tejkalon 10% të kohës totale të projektimit për një rënie të nivelit të ujit, pompimi i ujit për këtë pikë duhet të përsëritet. Në rastin e pompimit nga puse të pajisura me filtër me spërkatje, sasia e tkurrjes së materialit spërkatës duhet të matet gjatë pompimit një herë në ditë.
5.10. Shkalla e rrjedhjes (produktiviteti) e puseve duhet të përcaktohet nga një rezervuar matës me një kohë mbushjeje të paktën 45 s. Lejohet të përcaktohet shkalla e rrjedhës duke përdorur kanale dhe ujëmatës.
Niveli i ujit në pus duhet të matet me një saktësi prej 0.1% të thellësisë së nivelit të matur të ujit.
Shkalla e rrjedhës dhe nivelet e ujit në pus duhet të maten të paktën çdo 2 orë gjatë gjithë kohës së pompimit të përcaktuar nga projekti.
Matjet e kontrollit të thellësisë së pusit duhet të bëhen në fillim dhe në fund të pompimit në prani të një përfaqësuesi të klientit.
5.11. Gjatë procesit të pompimit, organizata e shpimit duhet të matë temperaturën e ujit dhe të marrë mostra uji në përputhje me GOST 18963-73 dhe GOST 4979-49 dhe t'i dorëzojë ato në laborator për të testuar cilësinë e ujit në përputhje me GOST 2874-82.
Cilësia e çimentimit të të gjitha vargjeve të shtresës së jashtme, si dhe vendndodhja e pjesës së punës të filtrit, duhet të kontrollohet duke përdorur metoda gjeofizike. Në fund të shpimit, gryka e një pusi vetë-rrjedhës duhet të pajiset me një valvul dhe një pajisje për një matës presioni.
5.12. Pas përfundimit të shpimit të pusit të marrjes së ujit dhe testimit të tij duke pompuar ujin, pjesa e sipërme e tubit të prodhimit duhet të saldohet me një kapak metalik dhe të ketë një vrimë të filetuar për një bulon në prizë për të matur nivelin e ujit. Projektimi dhe numrat e shpimit të pusit, emri i organizatës së shpimit dhe viti i shpimit duhet të shënohen në tub.
Për të funksionuar një pus, në përputhje me projektin, ai duhet të jetë i pajisur me instrumente për matjen e nivelit të ujit dhe shkallës së rrjedhës.
5.13. Pas përfundimit të testimit të shpimit dhe pompimit të një pusi të marrjes së ujit, organizata e shpimit duhet t'ia transferojë atë klientit në përputhje me kërkesat e SNiP 3.01.04-87, si dhe mostrat e shkëmbinjve të shpuar dhe dokumentacionin (pasaportën), duke përfshirë:
seksion gjeologjik dhe litologjik me projektim pusi, i korrigjuar sipas të dhënave të kërkimit gjeofizik;
vepron për vendosjen e një pusi, instalimin e një filtri, çimentimin e vargjeve të shtresës së jashtme;
një diagram përmbledhës të regjistrimit me rezultatet e interpretimit të tij, të nënshkruar nga organizata që ka kryer punën gjeofizike;
regjistri i vëzhgimeve të pompimit të ujit nga një pus uji;
të dhëna mbi rezultatet e analizave kimike, bakteriologjike dhe treguesve organoleptikë të ujit në përputhje me GOST 2874-82 dhe përfundimin e shërbimit sanitar-epidemiologjik.
Dokumentacioni duhet të bihet dakord me organizatën e projektimit përpara dorëzimit te klienti.
Strukturat kapacitore
5.14. Gjatë instalimit të strukturave të rezervuarit monolit dhe të parafabrikuar të betonit dhe betonit të armuar, përveç kërkesave të projektit, duhet të përmbushen edhe kërkesat e SNiP 3.03.01-87 dhe këto rregulla.
5.15. Mbushja e tokës në sinuse dhe spërkatja e strukturave kapacitore duhet të bëhet, si rregull, mënyrë të mekanizuar pas vendosjes së komunikimeve me strukturat e rezervuarëve, kryerjes së testeve hidraulike të strukturave, eliminimit të defekteve të identifikuara dhe hidroizolimit të mureve dhe tavaneve.
5.16. Pasi të kenë përfunduar të gjitha llojet e punës dhe betoni të arrijë forcën e tij të projektuar, kryhet një test hidraulik i strukturave të rezervuarit në përputhje me kërkesat e seksionit. 7.
5.17. Instalimi i sistemeve të kullimit dhe shpërndarjes së strukturave të filtrit mund të kryhet pas një testi hidraulik të kapacitetit të strukturës për rrjedhje.
5.18. Vrimat e rrumbullakëta në tubacionet për shpërndarjen e ujit dhe ajrit, si dhe për mbledhjen e ujit, duhet të shpohen në përputhje me klasën e treguar në projekt.
Devijimet nga gjerësia e projektimit të vrimave brenda tuba polietileni nuk duhet të kalojë 0.1 mm, dhe nga gjatësia e projektimit të hendekut në dritë ±3 mm.
5.19. Devijimet në distancat midis akseve të bashkimeve të kapakut në sistemet e shpërndarjes dhe daljes së filtrave nuk duhet të kalojnë ±4 mm, dhe në shenjat e majës së kapakut (përgjatë zgjatimeve cilindrike) - ±2 mm nga pozicioni i projektimit.
5.20. Shenjat e skajeve të pendës në pajisjet për shpërndarjen dhe grumbullimin e ujit (ulluqe, tabaka, etj.) duhet të korrespondojnë me dizajnin dhe duhet të jenë në përputhje me nivelin e ujit.
Kur instaloni tejmbushje me prerje trekëndore, devijimet e shenjave të pjesës së poshtme të prerjeve nga ato të projektimit nuk duhet të kalojnë ±3 mm.
5.21. Në brendësi dhe sipërfaqet e jashtme ulluqet dhe kanalet për mbledhjen dhe shpërndarjen e ujit, si dhe për mbledhjen e sedimenteve, duhet të jenë pa guaska dhe rritje. Tabakat e ulluqeve dhe kanaleve duhet të kenë një pjerrësi të përcaktuar nga projekti në drejtim të lëvizjes së ujit (ose sedimentit). Nuk lejohet prania e zonave me pjerrësi të kundërt.
5.22. Mjetet e filtrit mund të vendosen në struktura për pastrimin e ujit me anë të filtrimit pas testimit hidraulik të kontejnerëve të këtyre strukturave, larjes dhe pastrimit të tubacioneve të lidhura me to, testimit individual të funksionimit të secilit prej sistemeve të shpërndarjes dhe grumbullimit, matjes dhe mbylljes. jashtë pajisjeve.
5.23. Materialet e mediave të filtrit të vendosura në objektet e trajtimit të ujit, duke përfshirë biofiltrat, për sa i përket shpërndarjes së madhësisë së grimcave duhet të përputhen me dizajnin ose kërkesat e SNiP 2.04.02-84 dhe SNiP 2.04.03-85.
5.24. Devijimi i trashësisë së shtresës së çdo fraksioni të medias së filtrit nga vlera e projektimit dhe trashësia e të gjithë medias nuk duhet të kalojë ±20 mm.
5.25. Pas përfundimit të punës për shtrimin e ngarkesës së strukturës së filtrit të furnizimit me ujë të pijshëm, struktura duhet të lahet dhe dezinfektohet, procedura për të cilën është paraqitur në Shtojcën 5 të rekomanduar.
5.26. Instalimi i elementeve strukturorë të ndezshëm të spërkatësve prej druri, grilave të grumbullimit të ujit, paneleve udhëzuese të ajrit dhe ndarjeve të kullave ftohëse të ventilatorit dhe pishinave me spërkatje duhet të kryhet pas përfundimit të punës së saldimit.
6. KËRKESA SHTESË TË NDËRTIMIT
TUBACIONET DHE STRUKTURAT E FURNIZIMIT TË UJËS
DHE KANALIZIMET NE NATYRORE TE VEÇANTA
DHE KUSHTET KLIMATIKE
6.1. Gjatë ndërtimit të tubacioneve dhe strukturave të furnizimit me ujë dhe kanalizimeve në kushte të veçanta natyrore dhe klimatike, duhet të respektohen kërkesat e projektit dhe këtij seksioni.
6.2. Tubacionet e përkohshme të furnizimit me ujë, si rregull, duhet të vendosen në sipërfaqen e tokës në përputhje me kërkesat për vendosjen e tubacioneve të përhershme të furnizimit me ujë.
6.3. Ndërtimi i tubacioneve dhe strukturave në tokat e përhershme duhet të kryhet, si rregull, në temperatura negative të jashtme duke ruajtur tokat e ngrira të themelit. Në rastin e ndërtimit të tubacioneve dhe strukturave në temperatura pozitive të jashtme, është e nevojshme të mbahen tokat e themelit në gjendje të ngrirë dhe të parandalohen shkeljet e kushteve të temperaturës dhe lagështisë së tyre të përcaktuara nga projekti.
Përgatitja e bazës për tubacionet dhe strukturat në tokat e ngopura me akull duhet të kryhet duke i shkrirë ato deri në thellësinë e projektimit dhe ngjeshjen, si dhe duke zëvendësuar tokat e ngopura me akull me toka të ngjeshura të shkrira në përputhje me projektin.
Lëvizja e automjeteve dhe makinerive të ndërtimit gjatë verës duhet të kryhet përgjatë rrugëve dhe rrugëve hyrëse të ndërtuara në përputhje me projektin.
6.4. Ndërtimi i tubacioneve dhe strukturave në zonat sizmike duhet të kryhet në të njëjtat mënyra dhe metoda si në kushte normale ndërtimi, por me zbatimin e masave të parashikuara nga projekti për të siguruar rezistencën e tyre sizmike. Lidhjet e tubacioneve dhe pajisjeve të çelikut duhet të saldohen vetëm duke përdorur metoda me hark elektrik dhe cilësia e saldimit duhet të kontrollohet duke përdorur metoda të kontrollit fizik në masën 100%.
Gjatë ndërtimit të strukturave të rezervuarëve të betonit të armuar, tubacioneve, puseve dhe dhomave, duhet të përdorni llaçe çimentoje me aditivë plastifikues në përputhje me projektin.
6.5. E gjithë puna për të siguruar rezistencën sizmike të tubacioneve dhe strukturave të kryera gjatë procesit të ndërtimit duhet të pasqyrohet në regjistrin e punës dhe në raportet e inspektimit të punës së fshehur.
6.6. Në mbushje në sinuset e strukturave të tankeve të ndërtuara në zonat e minuara, duhet të sigurohet siguria e nyjeve të zgjerimit.
Boshllëqet e fugave të zgjerimit në të gjithë lartësinë e tyre (nga baza e themeleve deri në majën e pjesës së sipërme të themelit të strukturave) duhet të pastrohen nga dheu, mbeturinat e ndërtimit, depozitat e betonit, llaçi dhe mbetjet e kallepit.
Certifikatat e inspektimit të punës së fshehtë duhet të dokumentojnë të gjitha punët kryesore të veçanta, duke përfshirë: instalimin e fugave të zgjerimit, instalimin e fugave rrëshqitëse në strukturat e themeleve dhe nyjet e zgjerimit; ankorimi dhe saldimi në vendet ku janë instaluar nyjet e menteshave; instalimi i tubave që kalojnë nëpër muret e puseve, dhomave dhe strukturave të rezervuarëve.
6.7. Tubacionet në këneta duhet të vendosen në një kanal pasi uji të jetë kulluar prej tij ose në një kanal të përmbytur me ujë, me kusht që të merren masat e nevojshme në përputhje me projektin për të parandaluar notimin e tyre lart.
Fijet e tubacionit duhet të tërhiqen përgjatë kanalit ose të zhvendosen në det me skajet e mbyllura.
Vendosja e tubacioneve në diga të mbushura dhe të ngjeshura plotësisht duhet të bëhet si në kushtet normale të tokës.
6.8. Gjatë ndërtimit të tubacioneve në toka të fundosura, gropat për nyjet e prapanicës duhet të bëhen duke ngjeshur dheun.
7. TESTIMI I GYSATAJVE DHE KONSTRUKSIONEVE
Tubacionet me presion
7.1. Nëse nuk ka asnjë tregues në projekt për metodën e testimit, tubacionet nën presion i nënshtrohen testimit për forcë dhe ngushtësi, si rregull, me metodën hidraulike. Në varësi të kushteve klimatike në zonën e ndërtimit dhe në mungesë të ujit, një metodë testimi pneumatike mund të përdoret për tubacionet me një presion të brendshëm të projektimit Рр, jo më shumë se:
gizë nëntokësore, asbest-çimento dhe beton arme - 0,5 MPa (5 kgf/sq.cm);
çeliku nëntokësor - 1,6 MPa (16 kgf/sq.cm);
çeliku mbi tokë - 0,3 MPa (3 kgf/sq.cm).
7.2. Testimi i tubacioneve nën presion të të gjitha klasave duhet të kryhet nga një organizatë ndërtimi dhe instalimi, si rregull, në dy faza:
i pari është një provë paraprake për forcën dhe ngushtësinë, e kryer pas mbushjes së sinuseve me rrahje të tokës në gjysmën e diametrit vertikal dhe pluhurosjes së tubave në përputhje me kërkesat e SNiP 3.02.01-87 me nyje prapanicë të mbetur të hapura për inspektim; ky test mund të kryhet pa pjesëmarrjen e përfaqësuesve të klientit dhe organizatës operuese me hartimin e një raporti të miratuar nga inxhinieri kryesor i organizatës së ndërtimit;
e dyta - testi i pranimit (përfundimtar) për forcën dhe ngushtësinë duhet të kryhet pasi tubacioni të jetë mbushur plotësisht me pjesëmarrjen e përfaqësuesve të klientit dhe organizatës operuese me hartimin e një raporti mbi rezultatet e provës në formën e shtojcave të detyrueshme 1 ose 3.
Të dy fazat e provës duhet të kryhen përpara se të instalohen hidrantët, kunjat dhe valvulat e sigurisë, në vend të të cilave duhet të instalohen prizat e fllanxhave gjatë provës. Testimi paraprak i tubacioneve që janë të aksesueshme për inspektim në gjendje pune ose i nënshtrohen mbushjes së menjëhershme gjatë procesit të ndërtimit (puna në koha e dimrit, në kushte të ngushta), me justifikimin e duhur në projekte lejohet të mos realizohen.
7.3. Tubacionet e kalimeve nënujore i nënshtrohen testeve paraprake dy herë: në një rrëshqitje ose platformë pas saldimit të tubave, por para se të aplikoni izolim anti-korrozioni në nyjet e salduara, dhe përsëri - pas vendosjes së tubacionit në një kanal në pozicionin e projektimit, por më parë mbushja me dhe.
Rezultatet e testeve paraprake dhe të pranimit duhet të dokumentohen në një dokument në formën e Shtojcës 1 të detyrueshme.
7.4. Tubacionet e shtruara në kalimet përmes hekurit dhe rrugë makinash Kategoritë I dhe II i nënshtrohen testimit paraprak pas shtrimit të tubacionit të punës në një kasë (këllëf) përpara se të mbushet hapësira ndërmjet tubacioneve të zgavrës së kasës dhe përpara mbushjes së gropave të tranzicionit të punës dhe marrjes.
7.5. Vlerat e presionit të brendshëm të projektimit Рр dhe presionit të provës Рi për kryerjen e testeve paraprake dhe të pranimit të tubacionit të presionit për forcë duhet të përcaktohen nga projekti në përputhje me kërkesat e SNiP 2.04.02-84 dhe të tregohen në punë dokumentacionin.
Vlera e presionit të provës për ngushtësinë Pr për kryerjen e testeve paraprake dhe të pranimit të tubacionit të presionit duhet të jetë e barabartë me vlerën e projektimit të brendshëm
kufiri i matjes së presionit, klasa e saktësisë dhe ndarja e shkallës së matësit të presionit. Në këtë rast, vlera e Pr nuk duhet të kalojë vlerën e presionit të provës së pranimit të tubacionit për forcën Pi.
7.6* Tubacionet prej çeliku, gize, betoni të armuar dhe tuba asbest-çimento, pavarësisht nga metoda e provës, duhet të testohen me gjatësi më të vogël se 1 km - në të njëjtën kohë; për gjatësi më të gjata - në seksione jo më shumë se 1 km. Gjatësia e seksioneve të testimit të këtyre tubacioneve duke përdorur metodën e provës hidraulike lejohet të kalojë 1 km, me kusht që norma e lejueshme e rrjedhës së ujit të pompuar të përcaktohet si për një seksion 1 km të gjatë.
Tubacionet e bëra nga tuba LDPE, HDPE dhe PVC, pavarësisht nga metoda e provës, duhet të testohen në një gjatësi prej jo më shumë se 0,5 km në të njëjtën kohë, dhe për gjatësi më të gjata - në seksione jo më shumë se 0,5 km. Me arsyetimin e duhur, projekti lejon testimin e tubacioneve të specifikuara në një hap për një gjatësi deri në 1 km, me kusht që norma e lejueshme e rrjedhës së ujit të pompuar të përcaktohet si për një seksion 0.5 km të gjatë.
Tabela 4
për vlera të ndryshme të presionit të brendshëm të projektimit Рр në tubacion dhe karakteristikat e matësve teknikë të presionit të përdorur |
||||||||||||||||||
Madhësia e brendshme presioni i projektimit në tubacion Рр, MPa (kgf/sq.cm) |
Kufiri i sipërm i matjes së presionit, MPa (kgf/sq.cm) |
çmimi i ndarjes, MPa (kgf/cm katror) |
Kufiri i sipërm i matjes së presionit, MPa (kgf/sq.cm) |
çmimi i ndarjes, MPa (kgf/cm katror) |
Kufiri i sipërm i matjes së presionit, MPa (kgf/sq.cm) |
çmimi i ndarjes, MPa (kgf/cm katror) |
MPa (kgf/cm katror) |
|||||||||||
Klasat e saktësisë së matësve teknikë të presionit |
||||||||||||||||||
Nga 0,41 në 0,75 (nga 4.1 në 7.5) |
||||||||||||||||||
Nga 0.76 në 1.2 (nga 7.6 në 12) |
||||||||||||||||||
Nga 1.21 në 2.0 (nga 12.1 në 20) |
||||||||||||||||||
Nga 2.01 në 2.5 (nga 20.1 në 25) |
||||||||||||||||||
Nga 2.51 në 3.0 (nga 25.1 deri në 30) |
||||||||||||||||||
Nga 3.01 në 4.0 (nga 30.1 në 40) |
||||||||||||||||||
Nga 4.01 në 5.0 (nga 40.1 në 50) |
7.7. Nëse nuk ka udhëzime në projekt për vlerën e presionit të provës hidraulike Pi për kryerjen e një prove paraprake të tubacioneve të presionit për forcën, vlera merret në përputhje me Tabelën. 5*.
Tabela 5*
Karakteristikat e tubacionit |
Vlera e presionit të provës gjatë testimit paraprak, MPa (kgf/sq.cm) |
|
1. Çeliku i klasës I* me nyje të salduara me prapanicë (përfshirë nën ujë) me presion të brendshëm të projektimit Рр deri në 0,75 MPa (7,5 kgf/sq.cm) |
||
2. E njëjta gjë, nga 0,75 në 2,5 MPa (nga 7,5 në 25 kgf/sq.cm) |
Presioni i brendshëm i projektimit me një koeficient prej 2, por jo më shumë se presioni i provës në fabrikë i tubave |
|
3. Njësoj, St. 2,5 MPa (25 kgf/sq.cm) |
||
4. Çeliku, i përbërë nga seksione të veçanta të lidhura në fllanxha, me një presion të brendshëm të projektimit Рр deri në 0,5 MPa (5 kgf/sq.cm) |
||
5. Çeliku i klasit 2 dhe 3 me nyje prapanicë me saldim dhe me presion të brendshëm të projektimit Рр deri në 0,75 MPa (7,5 kgf/sq.cm) |
||
6. E njëjta gjë, nga 0,75 në 2,5 MPa (nga 7,5 në 25 kgf/sq.cm) |
Presioni i brendshëm i projektimit me një koeficient prej 1.5, por jo më shumë se presioni i provës në fabrikë i tubave |
|
7. E njëjta gjë. St. 2,5 MPa (25 kgf/sq.cm) |
Presioni i brendshëm i projektimit me një koeficient prej 1.25, por jo më shumë se presioni i provës në fabrikë i tubave |
|
8. Marrja e ujit nga graviteti i çelikut ose dalje e kanalizimeve |
Instaluar sipas projektit |
|
9. Gize me fuga prapanicë për mbyllje (sipas GOST 9583-75 për tubat e të gjitha klasave) me presion të brendshëm të projektimit deri në 1 MPa (10 kgf/sq.cm) |
Presioni i brendshëm i projektimit plus 0.5 (5), por jo më pak se 1 (10) dhe jo më shumë se 1.5 (15) |
|
10. E njëjta gjë, me nyje prapanicë në pranga gome për tubat e të gjitha klasave |
Presioni i brendshëm i projektimit me një koeficient prej 1.5, por jo më pak se 1.5 (15) dhe jo më shumë se 0.6 të presionit hidraulik të testit të fabrikës |
|
11. Betoni i armuar |
Presioni i brendshëm i projektimit me një faktor 1.3, por jo më shumë se presioni i provës i papërshkueshëm nga uji i fabrikës |
|
12. Asbest-çimento |
Presioni i brendshëm i projektimit me një koeficient 1.3, por jo më shumë se 0.6 të presionit të provës të papërshkueshëm nga uji të fabrikës |
|
13. Plastike |
Presioni i brendshëm i projektimit me një faktor 1.3 |
* Klasat e tubacioneve pranohen sipas SNiP 2.04.02-84.
7.8. Përpara kryerjes së testeve paraprake dhe të pranimit të tubacioneve nën presion duhet të ketë:
ka përfunduar e gjithë puna për mbylljen e nyjeve të prapanicës, instalimin e ndalesave, instalimin e pjesëve lidhëse dhe pajisjeve, janë marrë rezultate të kënaqshme të kontrollit të cilësisë së saldimit dhe izolimit të tubacioneve të çelikut;
prizat e fllanxhave u instaluan në kthesa në vend të hidrantëve, kunjave, valvulave të sigurisë dhe në pikat e lidhjes me tubacionet operative;
janë përgatitur mjetet për mbushjen, shtrëngimin dhe zbrazjen e zonës së provës, janë instaluar komunikime të përkohshme dhe janë instaluar instrumentet dhe çezmat e nevojshme për testim;
puset për prodhim u drenazhuan dhe u ajrosën punë përgatitore, u organizua shërbimi në kufirin e zonës së sigurisë;
Seksioni i testuar i tubacionit është i mbushur me ujë (me metodën e provës hidraulike) dhe ajri hiqet prej tij.
Procedura për testimin hidraulik të tubacioneve nën presion për forcën dhe ngushtësinë është përcaktuar në Shtojcën 2 të rekomanduar.
7.9. Për të testuar tubacionin, kontraktorit përgjegjës duhet t'i lëshohet një leje pune për punë me rrezik të lartë, duke treguar madhësinë e zonës së sigurisë. Forma e lejes dhe procedura për lëshimin e saj duhet të përputhen me kërkesat e SNiP III-4-80*.
7.10. Për të matur presionin hidraulik gjatë testeve paraprake dhe të pranimit të tubacioneve për forcën dhe ngushtësinë, matës presioni të çertifikuar siç duhet të një klase saktësie prej të paktën 1,5 me një diametër trupi prej të paktën 160 mm dhe një shkallë për një presion nominal prej rreth 4/3 të testit Pi duhet të përdoret.
Kupat ose matësat matëse duhet të përdoren për të matur vëllimin e ujit të pompuar brenda dhe jashtë tubacionit gjatë testimit. ujë të ftohtë(ujëmatës) në përputhje me GOST 6019-83, të çertifikuar në mënyrën e përcaktuar.
7.11. Mbushja e tubacionit nën provë me ujë duhet të kryhet, si rregull, me një intensitet, m/h kub, jo më shumë se: 4 - 5 - për tubacionet me diametër deri në 400 mm; 6 -10 - për tubacionet me diametër nga 400 në 600 mm; 10 - 15 - për tubacionet me diametër 700 - 1000 mm dhe 15 - 20 - për tubacionet me diametër mbi 1100 mm.
Kur mbushni tubacionin me ujë, ajri duhet të hiqet përmes çezmave dhe valvulave të hapura.
7.12. Testimi hidraulik i pranimit të një tubacioni presioni mund të fillojë pas mbushjes së tij me tokë në përputhje me kërkesat e SNiP 3.02.01-87 dhe mbushjes së tij me ujë për qëllime të ngopjes me ujë, dhe nëse ai është mbajtur në gjendje të mbushur për në së paku: 72 orë - për gypat e betonit të armuar (duke përfshirë 12 orë nën presionin e brendshëm të projektimit Рр); tuba asbest-çimento - 24 orë (përfshirë 12 orë nën presion të brendshëm të projektimit Рр); 24 orë - për tubat prej gize. Për tubacionet e çelikut dhe polietilenit, ekspozimi për qëllime të ngopjes me ujë nuk kryhet.
Nëse tubacioni është mbushur me ujë përpara se të mbushet me tokë, atëherë kohëzgjatja e specifikuar e ngopjes së ujit përcaktohet nga momenti i mbushjes së tubacionit.
7.13. Tubacioni i presionit njihet se ka kaluar testet hidraulike paraprake dhe pranuese për rrjedhjet nëse shkalla e rrjedhës së ujit të pompuar nuk e kalon normën e lejuar të rrjedhës së ujit të pompuar për një seksion testimi prej 1 km ose më shumë në gjatësi të specifikuar në tabelë. 6*.
Nëse rrjedha e ujit të pompuar tejkalon kufirin e lejuar, atëherë tubacioni konsiderohet se ka dështuar në test dhe duhet të merren masa për zbulimin dhe eliminimin e defekteve të fshehura në tubacion, pas së cilës tubacioni duhet të ritestohet.
RREGULLAT E NDËRTIMIT
TË BRENDSHËM
SISTEMET SANITARE
SNiP 3.05.01-85
Komiteti Shtetëror i BRSS për Çështjet e Ndërtimit
Moskë 1988
ZHVILLUAR nga Instituti Shtetëror i Dizajnit Proektpromventiliya dhe Instituti i Kërkimeve Shkencore Gjithë Bashkimi i Hidromekanizimit, Punimeve Sanitare dhe Speciale të Ndërtimit (VNIIGS) të Ministrisë së BRSS të Montazhspetsstroy (Ph.D. P.A. Ovchinnikov- udhëheqësi i temës; E. N. Zaretsky, L.G. Sukhanova, V.S. Nefedova; kandidatët e teknikës shkencat A.G. Yashkul, G.S. Shkalikov).
PARAQITUR nga Ministria e BRSS e Montazhspetsstroy.
PËRGATITUR PËR MIRATIMIN NGA Glavtekhnormirovanie Gosstroy BRSS ( NË TË. Shishov).
Me hyrjen në fuqi të SNiP 3.05.01-85 "Sistemet e brendshme sanitare", SNiP humbet fuqinë e tij III -28-75 “Pajisjet sanitare dhe teknike të ndërtesave dhe strukturave”.
Kur përdorni një dokument rregullator, duhet të merrni parasysh ndryshimet e miratuara në kodet e ndërtimit dhe standardet shtetërore të botuara në revistën "Buletini i Pajisjeve të Ndërtimit", "Koleksioni i Ndryshimeve në rregulloret e ndërtimit dhe rregullat" e Komitetit Shtetëror të Ndërtimit të BRSS dhe indeksi i informacionit "Standardet Shtetërore të BRSS" të Standardit Shtetëror.
Reale Rregullat zbatohen për instalimin e sistemeve të brendshme të furnizimit me ujë të ftohtë dhe të nxehtë, ngrohjes, kanalizimeve, kullimit, ventilimit, ajrit të kondicionuar (përfshirë tubacionet në njësitë e ventilimit), dhomat e bojlerit me presion avulli deri në 0,07 MPa (0,7 kgf/cm 2) dhe temperaturat e ujit deri në 388 K (115 °C) gjatë ndërtimit dhe rindërtimit të ndërmarrjeve, ndërtesave dhe strukturave, si dhe për prodhimin e kanaleve të ajrit, montimeve dhe pjesëve nga tubacionet.
1. DISPOZITA TË PËRGJITHSHME
1.1. Instalimi i brendshëm sanitare sistemet duhet të prodhohen në përputhje me kërkesat e këtyre rregullave, SN 478-80, si dhe SNiP 3.01.01-85, SNiP III-4-80, SNiP III-3-81, standardet, specifikimet teknike dhe udhëzimet e pajisjeve prodhuesit.
Kur instaloni dhe prodhoni përbërës dhe pjesë të sistemeve të ngrohjes dhe tubacioneve në njësitë e ventilimit (në tekstin e mëtejmë "furnizimi me nxehtësi") me temperatura uji mbi 388 K (115 ° C) dhe avull me një presion pune më shumë se 0.07 MPa (0.7 kgf). /cm ) duhet të respektoni gjithashtu Rregullat për ndërtimin dhe funksionimin e sigurt të tubacioneve me avull dhe ujë të nxehtë, të miratuara nga Mbikëqyrja Teknike dhe Minierat Shtetërore e BRSS.
1.2. Instalimi i sistemeve të brendshme sanitare dhe dhomave të bojlerit duhet të kryhet duke përdorur metoda industriale nga montimet e tubacioneve, kanalet e ajrit dhe pajisjet e furnizuara të plota në blloqe të mëdha.
Gjatë instalimit të veshjeve ndërtesa industriale blloqe të mëdha, ajrimi dhe sisteme të tjera sanitare duhet të instalohen në blloqe përpara se t'i instaloni në pozicionin e projektimit.
Instalimi i sistemeve sanitare duhet të kryhet kur objekti (banimi) është gati për ndërtim në masën:
për pro ndërtesa industriale - e gjithë ndërtesa me një vëllim deri në 5000 m 3 dhe një pjesë e ndërtesës me një vëllim mbi 5000 m 3, duke përfshirë, në bazë të vendndodhjes, një të veçantë. dhoma e prodhimit, punishte, hapësirë, etj. ose një grup pajisjesh (përfshirë kanalizimet e brendshme, njësinë e ngrohjes, sistemin e ventilimit, një ose më shumë kondicionerë, etj.);
për ndërtesa banimi dhe publike deri në pesë kate - ndërtesë e veçantë, një ose më shumë seksione; mbi pesë kate - 5 kate të një ose më shumë seksioneve.
1.3. Përpara se të fillojë instalimi i sistemeve të brendshme sanitare, kontraktori i përgjithshëm duhet të kryejë punën e mëposhtme:
instalimi i tavaneve të dyshemesë, mureve dhe ndarjeve në të cilat do të instalohet sanitare pajisje;
ndërtimi i themeleve ose vendeve për instalimin e kaldajave, ngrohësve të ujit, pompave, ventilatorëve, kondicionerëve, shkarkimeve të tymit, ngrohësve të ajrit dhe pajisjeve të tjera sanitare;
ndërtimi i strukturave të ndërtesave për dhomat e ventilimit të sistemeve të furnizimit;
instalimi i hidroizolimit në vendet ku janë instaluar kondicionerët, dhomat e ventilimit të furnizimit dhe filtrat e lagësht;
ndërtimi i kanaleve për daljet e kanalizimeve në puset e para dhe puset me tabaka nga ndërtesa, si dhe vendosja e hyrjeve për komunikimet e jashtme të sistemeve sanitare në ndërtesë;
instalimi i dyshemeve (ose përgatitja e duhur) në zonat e instalimit pajisjet e ngrohjes në stendat dhe tifozët e instaluar në izoluesit e dridhjeve të pranverës, si dhe bazat "lundruese" për instalimin e pajisjeve të ventilimit;
rregullimi i mbështetësve për instalimin e tifozëve të çatisë, boshteve të shkarkimit dhe deflektorëve në sipërfaqet e ndërtesave, si dhe mbështetëse për tubacionet e vendosura në kanale nëntokësore dhe nëntokë teknike;
përgatitja e vrimave, brazdave, nyjeve dhe foleve në themele, mure, ndarje, dysheme dhe veshje të nevojshme për vendosjen e tubacioneve dhe kanaleve të ajrit;
vizatimi në muret e brendshme dhe të jashtme të të gjitha dhomave shenja ndihmëse të barabarta me shenjat e projektimit të dyshemesë së përfunduar plus 500 mm;
instalimi i kornizave të dritareve, dhe në ndërtesat e banimit dhe publike - dërrasat e pragut të dritareve;
suvatimin(il dhe veshja) sipërfaqet e mureve dhe kamareve në vendet ku janë instaluar pajisjet sanitare dhe ngrohëse, vendosen tubacione dhe kanale ajri, si dhe suvatimi i sipërfaqes së brazdave për instalimin e fshehur të tubacioneve në muret e jashtme;
përgatitja e hapjeve të instalimit në mure dhe tavane për furnizimin e pajisjeve të mëdha dhe kanaleve të ajrit;
instalimi në përputhje me dokumentacionin e punës të pjesëve të ngulitura në strukturat e ndërtimit për pajisjet e fiksimit, kanalet e ajrit dhe tubacionet;
ofrojnë sigurimi i mundësisë së ndezjes së veglave elektrike, si dhe makinave elektrike të saldimit, në një distancë prej jo më shumë se 50 m nga njëra-tjetra;
lustrimi i hapjeve të dritareve në rrethojat e jashtme, izolimi i hyrjeve dhe hapjeve.
1. 4. Ndërtimi i përgjithshëm, sanitare dhe punë të tjera të veçanta duhet të kryhen në objektet sanitare në rendin e mëposhtëm:
përgatitje për dysheme, suvatimin muret dhe tavanet, instalimi i fenerëve për instalimin e shkallëve;
instalimi i mjeteve të fiksimit, shtrimi i tubacioneve dhe kryerja e testimit të tyre hidrostatik ose presioni; hidroizolim i dyshemeve;
abetare mure, montimi i dyshemeve të pastra;
instalimi i vaskave, kllapave për lavamanë dhe pjesëve të montimit për cisternat e shpëlarjes;
lyerja e parë e mureve dhe tavaneve, tjegulla;
instalimi i lavamanëve, tualeteve dhe sternave të shpëlarjes;
lyerja e dytë e mureve dhe tavaneve; instalimi i pajisjeve të ujit.
Ndërtimi, sanitare dhe punë të tjera speciale në dhomat e ventilimit duhet të kryhen në rendin e mëposhtëm:
përgatitja për dysheme, vendosja e themeleve, suvatimi i mureve dhe tavaneve;
rregullimi i hapjeve të instalimit, instalimi i trarëve të vinçit;
punë në instalimin e dhomave të ventilimit; hidroizolim i dyshemeve;
instalimi i ngrohësve me tubacione;
instalimi i pajisjeve të ventilimit dhe kanaleve të ajrit dhe punë të tjera sanitare dhe elektrike;
testi i mbushjes me ujë të tabakasë së dhomës së ujitjes; punë izoluese (izolimi i nxehtësisë dhe zërit);
Puna e mbarimit(duke përfshirë mbylljen e vrimave në tavane, mure dhe ndarje pas shtrimit të tubacioneve dhe kanaleve të ajrit);
në ndërtimi i dyshemeve të pastra.
Gjatë instalimit të sistemeve sanitare dhe kryerjes së punimeve civile përkatëse, nuk duhet të ketë dëmtime në punën e përfunduar më parë.
1.5 Dimensionet e vrimave dhe brazdave për vendosjen e tubacioneve në tavanet, muret dhe ndarjet e ndërtesave dhe strukturave merren në përputhje me ato të rekomanduara, përveç nëse projekti parashikon dimensione të tjera.
1. 6. Saldimi i tubave të çelikut duhet të bëhet me çdo metodë të rregulluar me standarde.
Llojet e nyjeve të salduara të tubacioneve të çelikut, forma, dimensionet e projektimit të saldimit duhet të përputhen me kërkesat e GOST 16037-80.
Saldimi i tubave të çelikut të galvanizuar duhet të kryhet me tela vetëmbrojtëse Sv-15GSTU TsA me Se në përputhje me GOST 2246-70 me diametër 0,8-1,2 mm ose elektroda me një diametër jo më shumë se 3 mm me një rutile ose veshje me fluor kalciumi, nëse nuk është dakorduar përdorimi i materialeve të tjera salduese në përputhje me procedurën e përcaktuar.
Lidhja e tubave, pjesëve dhe montimeve të çelikut të galvanizuar me saldim gjatë instalimit dhe në impiantin e prokurimit duhet të kryhet me kusht që të sigurohet thithja lokale e emetimeve toksike ose pastrimi i veshjes së zinkut në një gjatësi prej 20-30 mm nga skajet e bashkuara. të tubave, e ndjekur nga lyerja e sipërfaqes së jashtme të saldimit dhe e zonës së prekur nga nxehtësia me bojë, që përmban 94% pluhur zinku (nga pesha) dhe 6% lidhës sintetikë (polisterol, gomë e klorur, rrëshirë epokside).
Gjatë saldimit të tubave, pjesëve dhe montimeve të çelikut, duhet të plotësohen kërkesat e GOST 12.3.003-75.
Lidhja e tubave të çelikut (të pagalvanizuara dhe të galvanizuara), si dhe pjesëve dhe montimeve të tyre me diametër nominal deri në 25 mm përfshirëse, në kantierin e ndërtimit duhet të bëhet me saldim në xhiro (me njërin skaj të tubit të shtrirë. ose një bashkim pa fije). Lidhjet e shtyllave të tubave me diametër nominal deri në 25 mm përfshirëse mund të kryhen në impiantet e prokurimit.
Gjatë saldimit, sipërfaqet e filetuara dhe sipërfaqet e fllanxhave duhet të mbrohen nga spërkatjet dhe pikat e metalit të shkrirë.
NË Saldimi duhet të jetë pa çarje, zgavra, pore, prerje, kratere të pa salduar, si dhe djegie dhe njolla të metalit të depozituar.
Vrimat në tuba me diametër deri në 40 mm për saldimin e tubave duhet të bëhen, si rregull, duke shpuar, bluar ose prerë në një shtypës.
Diametri i vrimës duhet të jetë i barabartë me diametrin e brendshëm të tubit me devijime të lejueshme + 1 mm.
1.7. Instalimi i sistemeve sanitare në ndërtesa komplekse, unike dhe eksperimentale duhet të kryhet në përputhje me kërkesat e këtyre rregullave dhe udhëzimeve të veçanta në dokumentacionin e punës.
2. PUNË PËRGATITORE
PRODHIMI I NJËSIVE DHE PJESËVE TË GYSATAVE NGA TUBAT E ÇELIKUT
2.1. Prodhimi i komponentëve dhe pjesëve të tubacionit nga gypat e çelikut duhet të kryhet në përputhje me specifikimet teknike dhe standardet. Tolerancat e prodhimit nuk duhet të kalojnë vlerat e specifikuara në.
Tabela 1
Vlera e tolerancës |
|
Devijimi: |
|
nga pinguliteti i skajeve të tubave të prerë |
Jo më shumë se 2 ° |
gjatësia e pjesës së punës |
± 2 mm për gjatësi deri në 1 m dhe ± 1 mm për çdo metër pasues |
Dimensionet e grykave në vrima dhe në skajet e tubave të prerë |
Jo më shumë se 0,5 mm |
Ovaliteti i tubave në zonën e lakimit |
Jo më shumë se 10% |
Numri i fijeve me fije jo të plota ose të thyera |
|
Devijimi i gjatësisë së fillit: |
|
i shkurtër |
|
2.2. Lidhja e tubave të çelikut, si dhe pjesëve dhe montimeve të bëra prej tyre, duhet të kryhet me saldim, fije, dado bashkimi dhe fllanxha (tek pajisje dhe pajisje).
Tubat, montimet dhe pjesët e galvanizuara duhet të lidhen, si rregull, me fije që përdorin pjesë lidhëse prej çeliku të galvanizuar ose hekur duktil jo të galvanizuar, në dado dhe fllanxha bashkimi (me pajisje dhe pajisje).
Për lidhjet e filetuara të tubave të çelikut, duhet të përdoren fijet cilindrike të tubave, të bëra në përputhje me GOST 6357-81 (klasa e saktësisë B) duke u rrotulluar në tuba të lehta dhe duke filetuar në tuba të zakonshëm dhe të përforcuar.
Kur bëni fije duke përdorur metodën e rrotullimit në një tub, lejohet të zvogëlohet diametri i tij i brendshëm deri në 10% përgjatë gjithë gjatësisë së fillit.
2.3. Kthesat e tubacioneve në sistemet e ngrohjes dhe furnizimit me ngrohje duhet të kryhen duke përkulur tubacione ose duke përdorur kthesa të salduara pa probleme të bëra prej çeliku të karbonit në përputhje me GOST 17375-83.
Rrezja lakimi i tubave me një vrimë nominale deri në 40 mm përfshirëse duhet të jetë së paku 2.5D n ar, a me një vrimë nominale prej 50 mm ose më shumë - të paktën 3.5D n ar tuba.
2.4. Në sistemet e furnizimit me ujë të ftohtë dhe të nxehtë, kthesat e tubacionit duhet të bëhen duke instaluar bërryla në përputhje me GOST 8946-75, kthesa ose përkulje tubash. Tubat e galvanizuar duhet të përkulen vetëm kur janë të ftohtë.
Për tubat me diametër 100 mm ose më shumë, lejohet përdorimi i kthesave të përkulura dhe të salduara. Rrezja minimale e këtyre kthesave duhet të jetë jo më pak se një diametër e gjysmë nominal i tubit.
Në Kur përkulni tubacionet e salduara, saldimi duhet të vendoset në pjesën e jashtme të boshllëkut të tubit dhe në një kënd prej të paktën 45 ° te rrafshi i përkuljes.
2.5. Saldimi me saldim në seksionet e lakuara të tubave në elementët e ngrohjes të paneleve të ngrohjes nuk lejohet.
2.6. Gjatë montimit të njësive, lidhjet me fileto duhet të vulosen. Si izolues për lidhjet me fileto në temperaturat e mjetit lëvizës deri në 378 K (105 ° C), përfshirëse, shirit i bërë nga fluoroplastike vulosje material (FUM) ose fije liri të ngopura me plumb të kuq ose të bardhë të përzier me vaj tharjeje.
Si izolues për lidhjet me fileto në temperatura të lëngut mbi 378 K (105 ° C) dhe për linjat e kondensimit duhet përdorur shirit FUM ose fije azbesti së bashku me fijet e lirit, të ngopura me grafit të përzier me vaj liri.
Fjongo Fijet FUM dhe liri duhet të aplikohen në një shtresë të barabartë përgjatë fillit dhe të mos dalin brenda ose jashtë tubit.
Si izolues për lidhjet me fllanxha në një temperaturë të mediumit të transportuar jo më shumë se 423 K (150 ° C) duhet të përdoret paroniti me trashësi 2-3 mm ose fluoroplastik-4, dhe në temperatura jo më të larta se 403 K (130 ° C) - guarnicione të bëra prej gome rezistente ndaj nxehtësisë.
Për lidhjet me fileto dhe me fllanxha, të tjera materialet e vulosjes, duke siguruar ngushtësi të lidhjeve në temperaturën e projektimit të ftohësit dhe të rënë dakord në mënyrën e përcaktuar.
2.7. Fllanxhat lidhen me tubin me saldim.
Devijimi nga pingulja e fllanxhës së salduar në tub në lidhje me boshtin e tubit lejohet deri në 1% të diametrit të jashtëm të fllanxhës, por jo më shumë se 2 mm.
Sipërfaqja e fllanxhave duhet të jetë e lëmuar dhe pa gërvishtje. Kokat e bulonave duhet të vendosen në njërën anë të lidhjes.
N Në seksionet vertikale të tubacioneve, dadot duhet të vendosen në fund.
Skajet e bulonave, si rregull, nuk duhet të dalin nga dado me më shumë se 0,5 diametra bulonash ose 3 hapa fije.
Fundi i tubit, duke përfshirë shtresën e saldimit nga fllanxha në tub, nuk duhet të zgjatet përtej sipërfaqes së fllanxhës.
P Hapësirat në lidhjet me fllanxha nuk duhet të mbivendosen me vrimat e bulonave.
U Instalimi i disa guarnicioneve ose me kënd midis fllanxhave nuk lejohet.
2.8. Devijimet në dimensionet lineare të njësive të montuara nuk duhet të kalojnë ±3 mm për një gjatësi deri në 1 m dhe ±1 mm për çdo metër pasues.
PRODHIM KAJALET E AJRIMIT METAL
2.1 8. Kanalet e ajrit dhe pjesët e sistemeve të ventilimit duhet të prodhohen në përputhje me dokumentacionin e punës dhe specifikimet teknike të miratuara siç duhet.
2.19. Kanalet e ajrit të bërë nga fletë metalike e hollë çeliku për çati me një diametër dhe një madhësi anësore më të madhe deri në 2000 mm duhet të bëhen me mbyllje spirale ose tegel të drejtë në tegela, të salduara me spirale ose me tegel të drejtë në saldim, dhe kanalet e ajrit me një madhësi anësore më shumë se 2000 mm duhet të jetë prej panelesh (të salduara, të salduara me ngjitës).
Kanalet e ajrit të bërë nga plastika metalike duhet të bëhen në qepje, dhe nga çelik inox, titani, si dhe fletë alumini dhe lidhjet e tij - në qepje ose saldim.
2.20. Fletët e çelikut me trashësi më të vogël se 1,5 mm duhet të mbivendosen me saldim, dhe 1,5-2 mm të trasha duhet të mbivendosen ose të saldohen prapanicë. Fletët më të trasha se 2 mm duhet të saldohen me prapanicë.
2.21. Për nyjet e salduara të seksioneve të drejta dhe pjesëve në formë të kanaleve të ajrit të bërë nga çati me fletë të hollë dhe çelik inox, duhet të përdoren metodat e mëposhtme të saldimit: plazma, harku automatik dhe gjysmë automatik i zhytur ose në një mjedis me dioksid karboni, kontakti, rul dhe hark manual.
Për saldimin e kanaleve të ajrit të bërë nga fletë alumini dhe lidhjet e tij, duhet të përdoren metodat e mëposhtme të saldimit:
argon-hark automatik - me një elektrodë harxhuese;
argon-hark manual - elektrodë jo harxhuese me tela mbushëse;
gazi
Për të bashkuar kanalet e ajrit të titanit, duhet të përdoret saldimi me hark me argon me një elektrodë harxhuese.
2.22. Kanalet e ajrit të bërë nga fletë alumini dhe lidhjet e tij me trashësi deri në 1,5 mm duhet të bëhen në qepje, me trashësi nga 1,5 deri në 2 mm - në qepje ose saldim, dhe me një trashësi fletë më shumë se 2 mm - në saldim .
Tegelat gjatësore në kanalet e ajrit të bërë nga çati me fletë të hollë dhe çeliku inox dhe fletë alumini me diametër ose madhësi anësore më të madhe prej 500 mm ose më shumë duhet të sigurohen në fillim dhe në fund të seksionit të kanalit të ajrit me saldim në vend, ribatina elektrike, ribatina. ose kapëse.
Qepjet në kanalet e ajrit, pavarësisht nga trashësia e metalit dhe mënyra e prodhimit, duhet të bëhen me një prerje.
2.23. Seksionet fundore të tegelave në skajet e kanaleve të ajrit dhe në hapjet e shpërndarjes së ajrit të kanaleve plastike të ajrit duhet të sigurohen me ribatina alumini ose çeliku me një shtresë oksidi, duke siguruar funksionimin në mjedise agresive të specifikuara në dokumentacionin e punës.
Të palosur Qepjet duhet të kenë të njëjtën gjerësi përgjatë gjithë gjatësisë dhe të jenë të vendosura fort në mënyrë uniforme.
2.24. Nuk duhet të ketë lidhje tegel në formë kryqi në kanalet e tegelit, si dhe në grafikët e prerjes.
2.25. Në seksionet e drejta të kanaleve të ajrit drejtkëndëshe me një seksion kryq anësor më shumë se 400 mm, ngurtësuesit duhet të bëhen në formën e kreshtave me një hap prej 200-300 mm përgjatë perimetrit të kanalit ose kthesave diagonale (kreshtave). Nëse ana është më shumë se 1000 mm, përveç kësaj, është e nevojshme të instaloni korniza të ngurtësisë së jashtme ose të brendshme, të cilat nuk duhet të dalin në kanalin e ajrit më shumë se 10 mm. Kornizat ngurtësuese duhet të fiksohen mirë me saldim në vend, ribatina elektrike ose ribatina.
Në kanalet e ajrit metal-plastikë, kornizat ngurtësuese duhet të instalohen duke përdorur ribatina alumini ose çeliku me një shtresë oksidi, duke siguruar funksionimin në mjedise agresive të specifikuara në dokumentacionin e punës.
2.26. Elementet e pjesëve në formë duhet të lidhen me njëri-tjetrin duke përdorur kreshta, palosje, saldim dhe thumba.
Elementet e pjesëve të formuara prej metali-plastikë duhet të lidhen me njëri-tjetrin duke përdorur palosjet.
Zigovye lidhjet për sistemet e transportit ajror lagështia e lartë ose të përziera me pluhur shpërthyes nuk lejohen.
2.27. Lidhja e seksioneve të kanalit të ajrit duhet të bëhet duke përdorur një metodë të tipit vafer ose duke përdorur fllanxha. Lidhjet duhet të jenë të forta dhe të ngushta.
2.28. Fllanxhat në kanalet e ajrit duhet të fiksohen me fllanxha me zig të qëndrueshëm, me saldim, me saldim në pikë ose me ribatina me diametër 4-5 mm, të vendosura çdo 200-250 mm, por me jo më pak se katër ribatina.
Fllanxhat në kanalet e ajrit metal-plastikë duhet të sigurohen duke fllanxhuar me një zig mbështetës.
Në kanalet e ajrit që transportojnë media agresive, fiksimi i fllanxhave duke përdorur zig nuk lejohet.
Nëse trashësia e murit të kanalit të ajrit është më shumë se 1 mm, fllanxhat mund të montohen në kanalin e ajrit pa fllanxha me saldim ngjitës dhe vulosje pasuese të hendekut midis fllanxhës dhe kanalit të ajrit.
2.29. Fllanxhaja e kanaleve të ajrit në vendet ku janë instaluar fllanxhat duhet të kryhet në mënyrë të tillë që fllanxha e përkulur të mos mbulojë vrimat për bulonat në fllanxha.
Fllanxhat janë instaluar pingul me boshtin e kanalit të ajrit.
2.30. Pajisjet rregulluese (portat, valvulat e mbytjes, amortizuesit, elementët e kontrollit të shpërndarësit të ajrit, etj.) duhet të mbyllen dhe hapen lehtësisht, si dhe të fiksohen në një pozicion të caktuar.
Motorët e damperit duhet të përshtaten fort me udhëzuesit dhe të lëvizin lirshëm në to.
Doreza e kontrollit të valvulës së mbytjes duhet të instalohet paralelisht me tehun e saj.
2.31. Kanalet e ajrit të bërë nga çeliku jo i galvanizuar, lidhësit e tyre lidhës (përfshirë sipërfaqet e brendshme të fllanxhave) duhet të lyhen (lyerën) në impiantin e prokurimit në përputhje me projektin (projektimi i detajuar).
Lyerja përfundimtare e sipërfaqes së jashtme të kanaleve të ajrit kryhet nga organizata të specializuara të ndërtimit pas instalimit të tyre.
Boshllëqet e ventilimit duhet të jenë të pajisura me pjesë për lidhjen e tyre dhe mjete fiksimi.
PAJISJET DHE PËRGATITJA PËR INSTALIM SANITARE DHE TEKNIKE PAJISJET, PAJISJET PËR NGROHJE, NJËSITË DHE PJESËT E gypave
2.32. Procedura për transferimin e pajisjeve, produkteve dhe materialeve përcaktohet nga Rregullat për kontratat e ndërtimit të kapitalit, të miratuara nga Këshilli i Ministrave të BRSS, dhe Rregulloret për marrëdhëniet e organizatave - kontraktorët e përgjithshëm me nënkontraktorët, të miratuara me një rezolutë të Komiteti Shtetëror i Ndërtimit të BRSS dhe Komiteti Shtetëror i Planifikimit të BRSS.
2.33. Asambletë dhe pjesët e bëra nga tubacionet për sistemet sanitare duhet të transportohen mbi objekte në kontejnerë ose çanta dhe kanë shoqëruese dokumentacionin.
Në çdo enë dhe ambalazh duhet të ngjitet një pllakë me shënimin e njësive të paketuara në përputhje me standardet aktuale dhe specifikimet teknike për prodhimin e produkteve.
2.34. Pajisjet, pajisjet e automatizimit, instrumentet, pjesët lidhëse, pajisjet e fiksimit, guarnicionet, bulonat, dadot, rondelet, etj. që nuk janë instaluar në pjesë dhe montime, duhet të paketohen veçmas dhe shenjat e kontejnerit duhet të tregojnë emërtimet ose emrat e këtyre. produkteve.
2.35. Kaldaja seksionale prej gize duhet të dorëzohen në kantieret e ndërtimit në blloqe ose pako, të montuara paraprakisht dhe të testohen në impiantet e prodhimit ose në ndërmarrjet e prokurimit të organizatave të instalimit.
Ngrohës uji,ngrohësit, pompat, njësitë e ngrohjes qendrore dhe individuale, njësitë matëse të ujit duhet të dorëzohen në objektet në ndërtim në mënyrë të transportueshme. instalimi i plotë blloqe me mjete fiksimi, tubacione, valvola mbyllëse, guarnicione, bulona, dado dhe rondele.
2. 36. Seksionet e radiatorëve prej gize duhet të montohen në pajisje në thithka duke përdorur guarnicione mbyllëse:
Dhe me gomë rezistente ndaj nxehtësisë 1,5 mm të trashë në një temperaturë të ftohësit deri në 403 K (1 30 ° C);
nga paroniti me trashësi 1 deri në 2 mm në një temperaturë të ftohësit deri në 423 K (150 ° C).
2.37. Radiatorët e riorganizuar prej gize ose blloqet e radiatorëve prej gize dhe tubacionet me pendë duhet të testohen duke përdorur metodën hidrostatike me presion prej 0,9 MPa (9 kgf/cm2) ose metodën e flluskave me presion prej 0,1 MPa (1 kgf/cm2). Rezultatet e testeve të flluskave janë baza për të bërë ankesa për cilësinë tek prodhuesit e pajisjeve të ngrohjes prej gize.
Blloqet e radiatorëve prej çeliku duhet të testohen duke përdorur metodën e flluskave në një presion prej 0,1 MPa (1 kgf/cm2).
Blloqet e konvektorëve duhet të testohen me metodën hidrostatike me presion 1,5 MPa (15 kgf/cm2) ose metodën e flluskave me presion 0,15 MPa (1,5 kgf/cm2).
Procedura e testimit duhet të përputhet me kërkesat -.
Pas provës, uji duhet të hiqet nga njësitë e ngrohjes.
Panelet e ngrohjes pas testimit hidrostatik duhet të pastrohen me ajër dhe tubat e tyre lidhës duhet të mbyllen me priza të inventarit.
3. PUNIME INSTALIMI DHE MONTIMI
DISPOZITAT E PËRGJITHSHME
3.1. Lidhja e tubave të çelikut të galvanizuar dhe jo të galvanizuar gjatë instalimit duhet të kryhet në përputhje me kërkesat e këtyre rregullave.
Lidhjet e shkëputshme në tubacione duhet të bëhen në montime dhe aty ku është e nevojshme sipas kushteve të montimit të tubacionit.
Lidhjet e shkëputshme të tubacioneve, si dhe pajisjet, inspektimet dhe pastrimi duhet të vendosen në vende të aksesueshme për mirëmbajtje.
3.2. Tubacionet vertikale nuk duhet të devijojnë nga vertikali me më shumë se 2 mm për 1 m gjatësi.
3.3. Tubacionet e paizoluara të sistemeve të ngrohjes, furnizimi me ngrohje, furnizimi i brendshëm me ujë të ftohtë dhe të nxehtë nuk duhet të jenë ngjitur me sipërfaqen e strukturave të ndërtesës.
Distanca nga sipërfaqja e suvasë ose veshjes në boshtin e tubacioneve të paizoluara me një diametër nominal deri në 32 mm përfshirëse me instalim të hapur duhet të jetë nga 35 në 55 mm, për diametrat 40-50 mm - nga 50 në 60 mm , dhe për diametra më shumë se 50 mm - pranohet sipas dokumentacionit të punës.
Distanca nga tubacionet, pajisjet e ngrohjes dhe ngrohësit e ajrit me një temperaturë ftohës mbi 378 K (105 ° C) në strukturat e ndërtesave dhe strukturave të bëra nga materiale të djegshme (të djegshme), të përcaktuara nga projekti (projektimi i detajuar) sipas GOST 12.1.044 -84, duhet të jetë së paku 100 mm.
3.4. Mjetet e fiksimit nuk duhet të vendosen në kryqëzimet e tubacioneve.
Nuk lejohen mbyllja e fiksimeve duke përdorur priza druri, si dhe saldimi i tubacioneve në mjetet e fiksimit.
Distanca midis mjeteve të fiksimit të tubacioneve të çelikut në seksione horizontale duhet të merret në përputhje me dimensionet e specifikuara në, përveç nëse ka udhëzime të tjera në dokumentacionin e punës.
Tabela 2
Distanca maksimale, m, ndërmjet mjeteve të fiksimit të tubacionit |
||
jo të izoluar |
i izoluar |
|
3.5. Mjetet për fiksimin e ngritësve prej tubash çeliku në ndërtesat e banimit dhe publike me lartësi dyshemeje deri në 3 m nuk janë instaluar, dhe për një lartësi dyshemeje më shumë se 3 m, mjetet e fiksimit janë instaluar në gjysmën e lartësisë së dyshemesë.
Mjetet për fiksimin e ngritësve në ndërtesat industriale duhet të instalohen çdo 3 m.
3.6. Distancat midis mjeteve të fiksimit të tubave të kanalizimeve prej gize gjatë vendosjes së tyre horizontale duhet të jenë jo më shumë se 2 m, dhe për ngritësit - një fiksim për dysheme, por jo më shumë se 3 m midis mjeteve të fiksimit. Mjetet e fiksimit duhet të vendosen nën priza.
3.7. Lidhjet me pajisjet e ngrohjes me një gjatësi prej më shumë se 1500 mm duhet të kenë fiksim.
3. 8. Pajisjet sanitare dhe ngrohëse duhet të jenë të instaluara si plumb dhe në nivel.
SanitarKabinat duhet të instalohen në një bazë të nivelit.
Para instalimit të kabinave sanitare, është e nevojshme të kontrolloni që niveli i pjesës së sipërme të pirgut të kanalizimeve të kabinës së poshtme dhe niveli i bazës përgatitore të jenë paralele.
Instalimi sanitare kabinat duhet të ndërtohen në mënyrë që akset e ngritësve të kanalizimeve të kateve ngjitur të përkojnë.
Aderimi sanitare instalimi i kabinave në kanalet e ventilimit duhet të kryhet përpara se të vendosen pllakat e dyshemesë së një dyshemeje të caktuar.
3.9. Testimi hidrostatik (hidraulik) ose manometrik (pneumatik) i tubacioneve për instalimin e fshehur të tubacioneve duhet të kryhet përpara se ato të mbyllen me hartimin e një raporti inspektimi për punën e fshehur në formën e Shtojcës 6 të detyrueshme. SNiP 3.01.01-85.
Testimi i tubacioneve të izoluara duhet të kryhet përpara aplikimit të izolimit.
Shpëlarja e sistemeve të furnizimit me ujë shtëpiak dhe të pijshëm konsiderohet e plotë pas lëshimit të ujit që plotëson kërkesat e GOST 2874-82 "Uji i pijshëm".
FURNIZIM I BRENDSHËM UJË I FTOHTË DHE I Nxehtë
3.11. Lartësia e instalimit të pajisjeve të ujit (distanca nga boshti horizontal i pajisjeve deri te pajisjet sanitare, mm) duhet të merret si më poshtë:
çezmat e ujit dhe miksera nga anët e lavamanëve - nga 250, dhe nga anët e lavamanëve - nga 200;
çezmat e tualetit dhe miksera nga anët e lavamanëve - nga 200.
Lartësia e instalimit të çezmave nga niveli i përfunduar i dyshemesë, mm:
çezmat e ujit në banja, çezmat e shkarkimit të tualetit, miksera të lavamanëve të inventarit në publik dhe institucionet mjekësore, miksera për banjë - 800;
rubineta për viduar me prizë të zhdrejtë - 800, me dalje direkte - 1000;
miksera dhe lavamanë për rroba vaji në institucione mjekësore, miksera të përgjithshme për vaska dhe lavamane, miksera me bërryla për lavamane kirurgjikale - 1100;
çezmat për larjen e dyshemeve në tualete ndërtesat publike - 600;
mikser dush - 1200.
Rrjetat e dushit duhet të instalohen në një lartësi prej 2100-2250 mm nga fundi i rrjetës deri në nivelin e dyshemesë së përfunduar, në kabina për personat me aftësi të kufizuara - në një lartësi prej 1700 - 1850 mm, në institucionet parashkollore - në një lartësi prej 1500 mm nga fundi i tabakasë. Devijimet nga dimensionet e specifikuara në këtë paragraf nuk duhet të kalojnë 20 mm.
Shënim: Për lavamanë me shpinë që kanë hapje për çezmat, si dhe për lavamanë dhe lavamanë me pajisje tavoline, lartësia e instalimeve dhe çezmave përcaktohet nga dizajni i pajisjes.
3.11a. Në dushet për personat me aftësi të kufizuara dhe në institucionet parashkollore duhet të përdoren rrjeta dushi me zorrë fleksibël.
Në dhomat për personat me aftësi të kufizuara, çezmat e ujit të ftohtë dhe të nxehtë, si dhe miksera, duhet të jenë me levë ose me veprim shtytës.
Përzierësit për lavamanë, lavamanë, si dhe çezmat për gropat e instaluar në dhomat e destinuara për personat me aftësi të kufizuara me defekte të gjymtyrëve të sipërme duhet të kenë kontroll të këmbës ose të bërrylit.
(Botim i ndryshuar. Amendamenti nr. 1).
3.12. Prizat e tubave dhe pajisjeve (me përjashtim të bashkimeve me dy fole) duhet të drejtohen kundër lëvizjes së ujit.
Gjatë instalimit, nyjet e tubave të kanalizimeve prej gize duhet të vulosen me litar kërpi të ngopur ose me kasetë të ngopur, pasuar nga mbyllja me llaç çimentoje të një shkalle të paktën 1 00 ose derdhja e llaçit. gips-alumin zgjerim i çimentos ose i shkrirë dhe i nxehtë në një temperaturë prej 403-408 K (130-135 ° Me squfur me shtimin e kaolinës 10% të pasuruar sipas GOST 19608-84 ose GOST 19607-74.
Lejohet përdorimi i materialeve të tjera mbyllëse dhe mbushëse, të miratuara sipas procedurës së përcaktuar.
Gjatë periudhës së instalimit, skajet e hapura të tubacioneve dhe hinkave të kullimit duhet të mbyllen përkohësisht me priza të inventarit.
3.13. Pajisjet sanitare duhet të ngjiten në strukturat prej druri me vida.
Dalja e tualetit duhet të lidhet drejtpërdrejt me prizën e tubit të daljes ose me tubin e daljes duke përdorur një bashkim prej gize, tub polietileni ose bashkim gome.
Priza e tubit të daljes për një tualet me dalje direkte duhet të instalohet në të njëjtën linjë me dyshemenë.
3.14. Tasat e tualetit duhet të fiksohen në dysheme me vida ose të ngjiten me ngjitës. Kur fiksoni me vida, një copë litari gome duhet të instalohet nën bazën e tualetit.
Ngjitja duhet të kryhet në një temperaturë dhome prej të paktën 278 K (5 ° C).
Për të arritur forcën e kërkuar, tualetet e ngjitura duhet të mbahen pa ngarkesë në një pozicion të palëvizshëm derisa bashkimi ngjitës të bëhet i fortë për të paktën 12 orë.
3.15. Lartësia e instalimit të pajisjeve sanitare nga niveli i përfunduar i dyshemesë duhet të korrespondojë me dimensionet e specifikuara në.
Tabela 3
Lartësia e instalimit nga niveli i përfunduar i dyshemesë, mm |
|||
Në ndërtesat e banimit, publike dhe industriale |
Në shkolla dhe spitale për fëmijë |
Në institucionet parashkollore dhe në ambiente për personat me aftësi të kufizuara që lëvizin me ndihmën e aparateve të ndryshme |
|
Lavamanë (deri në pjesën e sipërme të anës) |
|||
Lavaman dhe lavamanë (deri në majë të anës) |
|||
Banja (deri në majë të anës) |
|||
Urinalet me mur dhe tabaka (deri në pjesën e sipërme të anës) |
|||
Tabaka dushi (deri në pjesën e sipërme të anës) |
|||
Shatërvanë të varur të pijes (deri në majë të anës) |
Shënime: 1. Devijimet e lejuara lartësia e instalimit të pajisjeve sanitare për instalimet me qëndrim të lirë nuk duhet të kalojë ±20 mm, dhe për instalimin në grup të pajisjeve të ngjashme - 45 mm.
2. Tubi i shpëlarjes për larjen e tabakasë urinare duhet të drejtohet me vrima drejt murit në një kënd prej 45° poshtë.
3. Kur instaloni një mikser të zakonshëm për një lavaman dhe një banjë, lartësia e instalimit të lavamanit është 850 mm në pjesën e sipërme të anës.
4. Lartësia e instalimit të pajisjeve sanitare në institucionet mjekësore duhet të merret si më poshtë, mm:
lavaman i inventarit prej gize (deri në majë të anëve) - 650;
larje për rroba vaji - 700;
viduar (në krye) - 400;
rezervuari për zgjidhje dezinfektuese (në fund të rezervuarit) - 1230.
5. Distanca midis akseve të lavamanëve duhet të jetë së paku 650 mm, banjot e duarve dhe këmbëve, urinalëve - të paktën 700 mm.
6. Në dhomat për personat me aftësi të kufizuara, lavamanët, lavamanët dhe lavamanët duhet të vendosen në një distancë prej të paktën 200 mm nga muri anësor i dhomës.
(Botim i ndryshuar. Amendamenti nr. 1).
3.16. Në ambientet shtëpiake të ndërtesave publike dhe industriale, instalimi i një grupi lavamanësh duhet të sigurohet në një stendë të përbashkët.
3.17. Përpara testimit të sistemeve të kanalizimeve, për t'i mbrojtur ato nga ndotja, duhet të hiqen prizat e poshtme të sifoneve dhe duhet të hiqen kupat në sifonët e shisheve.
Ngrohja, FURNIZIMI I NXEHTËSISË DHE DHOMAT E KALDADAVE
3.18. Pjerrësia e linjave në pajisjet e ngrohjes duhet të bëhet nga 5 në 10 mm për gjatësi të linjës në drejtim të lëvizjes së ftohësit. Për gjatësinë e linjave deri në 500 mm, tubat nuk duhet të jenë të pjerrëta.
3.19. Lidhjet me tubacionet e lëmuara prej çeliku, gize dhe bimetalike duhet të bëhen duke përdorur fllanxha (priza) me vrima të vendosura në mënyrë ekscentrike për të siguruar heqjen e lirë të ajrit dhe kullimin e ujit ose kondensatës nga tubat. Për lidhjet me avull lejohet lidhja koncentrike.
3.20. Radiatorët e të gjitha llojeve duhet të instalohen në distanca, mm, jo më pak se: 60 - nga dyshemeja, 50 - nga sipërfaqja e poshtme e dërrasave të pragut të dritares dhe 25 - nga sipërfaqja e mureve të suvasë.
Në ambientet e institucioneve mjekësore dhe parandaluese dhe të institucioneve të fëmijëve, radiatorët duhet të instalohen në një distancë prej të paktën 100 mm nga dyshemeja dhe 60 mm nga sipërfaqja e murit.
Nëse nuk ka tabelë të pragut të dritares, duhet të merret një distancë prej 50 mm nga maja e pajisjes deri në fund të hapjes së dritares.
Kur vendosni tubacionet hapur, distanca nga sipërfaqja e kamares deri te pajisjet e ngrohjes duhet të sigurojë mundësinë e vendosjes së lidhjeve me pajisjet e ngrohjes në një vijë të drejtë.
3.21. Konvektorët duhet të instalohen në një distancë:
të paktën 20 mm nga sipërfaqja e mureve deri te finët e konvektorit pa shtresë;
mbyllni ose me një hendek prej jo më shumë se 3 mm nga sipërfaqja e murit deri te fijet e elementit ngrohës të një konvektori të montuar në mur me një shtresë të jashtme;
të paktën 20 mm nga sipërfaqja e murit në shtresën e jashtme të konvektorit të dyshemesë.
Distanca nga maja e konvektorit deri në fund të pragut të dritares duhet të jetë së paku 70% e thellësisë së konvektorit.
Distanca nga dyshemeja deri në fund të një konvektori të montuar në mur me ose pa shtresë duhet të jetë së paku 70% dhe jo më shumë se 150% e thellësisë së pajisjes ngrohëse të instaluar.
Nëse gjerësia e pjesës së spikatur të pragut të dritares nga muri është më shumë se 150 mm, distanca nga fundi i saj deri në majë të konvektorëve me një shtresë të jashtme duhet të jetë jo më pak se lartësia e ngritjes së shtresës së jashtme e nevojshme për ta hequr atë.
Lidhja e konvektorëve me tubacionet e ngrohjes duhet të bëhet me filetim ose saldim.
3.22. Tuba të lëmuar dhe me shirita duhet të instalohen në një distancë prej të paktën 200 mm nga dyshemeja dhe pllaka e dritares deri në boshtin e tubit më të afërt dhe 25 mm nga sipërfaqja e suvasë së mureve. Distanca midis boshteve të tubave ngjitur duhet të jetë së paku 200 mm.
3.23. Kur instaloni një pajisje ngrohjeje nën një dritare, buza e saj në anën e ngritësit, si rregull, nuk duhet të shtrihet përtej hapjes së dritares. Në këtë rast, kombinimi i boshteve vertikale të simetrisë së pajisjeve të ngrohjes dhe hapjeve të dritareve nuk është i nevojshëm.
3.24. Në një sistem ngrohjeje me një tub me lidhje të njëanshme të pajisjeve të ngrohjes në mënyrë të hapur, ngritësi që do të vendoset duhet të vendoset në një distancë prej 150 ± 50 mm nga buza e hapjes së dritares dhe gjatësia e lidhjeve me ngrohjen. pajisjet duhet të jenë jo më shumë se 400 mm.
3.25. Pajisjet e ngrohjes duhet të instalohen në kllapa ose në stendat e prodhuara në përputhje me standardet, specifikimet teknike ose dokumentacionin e punës.
Numri i kllapave duhet të instalohet në shkallën prej një për 1 m2 të sipërfaqes ngrohëse të një radiatori prej gize, por jo më pak se tre për radiator (përveç radiatorëve në dy seksione), dhe për tubacionet me fije - dy për tub. Në vend të kllapave të sipërme, lejohet instalimi i shiritave të radiatorit, të cilët duhet të vendosen në 2/3 e lartësisë së radiatorit.
Kllapat duhet të instalohen nën qafat e radiatorit, dhe nën gypat me pendë - në fllanxha.
Gjatë instalimit të radiatorëve në stenda, numri i këtyre të fundit duhet të jetë 2 - për numrin e seksioneve deri në 10 dhe 3 - për numrin e seksioneve më shumë se 10. Në këtë rast, pjesa e sipërme e radiatorit duhet të sigurohet.
3.26. Numri i lidhësve për bllok konvektori pa shtresë duhet të jetë:
për instalim me një rresht dhe me dy rreshta - 2 fiksim në mur ose dysheme;
për instalime me tre rreshta dhe katër rreshta - 3 fiksim në mur ose 2 fiksim në dysheme.
Për konvektorët e furnizuar të plotë me mjete montimi, numri i fiksimeve përcaktohet nga prodhuesi në përputhje me standardet për konvektorët.
3.27. Duhet të ngjiten kllapa për pajisjet e ngrohjes muret e betonit me dowels, dhe për muret me tulla - me dowels ose duke mbyllur kllapat me llaç çimentoje të klasës jo më të ulët se 100 në një thellësi prej të paktën 100 mm (pa marrë parasysh trashësinë e shtresës suva).
Nuk lejohet përdorimi i prizave prej druri për vendosjen e kllapave.
3.28. Akset e ngritësve të lidhur të paneleve të murit me elementë ngrohje të integruar duhet të përkojnë gjatë instalimit.
Lidhja e ngritësve duhet të kryhet duke përdorur saldim në prehër (me njërin skaj të tubit të përhapur ose të lidhur me një bashkim pa fije).
Lidhja e tubacioneve me ngrohësit e ajrit (ngrohësit, njësitë e ngrohjes) duhet të bëhet duke përdorur fllanxha, fije ose saldim.
Portat e thithjes dhe shkarkimit njësitë e ngrohjes Ato duhet të mbyllen përpara se të vihen në punë.
3.29. Valvulat dhe valvulat e kontrollit duhet të instalohen në mënyrë të tillë që mediumi të rrjedhë nën valvul.
Valvulat e kontrollit duhet të instalohen horizontalisht ose rreptësisht vertikalisht, në varësi të dizajnit të tyre.
Drejtimi i shigjetës në trup duhet të përkojë me drejtimin e lëvizjes së mediumit.
3.30. Boshtet e valvulave me rregullim të dyfishtë dhe valvulave kalimtare rregulluese duhet të instalohen vertikalisht kur pajisjet e ngrohjes janë të vendosura pa kamare, dhe kur instalohen në kamare - në një kënd prej 45 ° lart.
Boshtet e valvulave me tre drejtime duhet të vendosen horizontalisht.
3.31. Matës presioni të instaluar në tubacione me temperatura të ftohësit deri në 378 K (105 ° C), duhet të lidhet përmes një valvule me tre drejtime.
Matës presioni të instaluar në tubacione me një temperaturë të ftohësit mbi 378 K (105 ° C), duhet të lidhet përmes një tubi sifoni dhe një valvule trekahëshe.
3.32. Termometrat në tubacione duhet të instalohen në mëngë, dhe pjesa e zgjatur e termometrit duhet të mbrohet nga një kornizë.
Në tubacionet me një vrimë nominale deri në 57 mm përfshirëse, duhet të sigurohet një zgjerues në vendin ku janë instaluar termometrat.
3.33. Për lidhjet me fllanxha të tubacioneve të naftës, duhet të përdoren guarnicione të bëra nga paroniti i lagur në ujë të nxehtë dhe të fërkuar me grafit.
3.34. Kanalet e ajrit duhet të instalohen pavarësisht nga disponueshmëria pajisje teknologjike në përputhje me referencat dhe shenjat e projektimit. Lidhja e kanaleve të ajrit me pajisjet e përpunimit duhet të bëhet pas instalimit të tij.
3.35. Kanalet e ajrit të destinuara për transportimin e ajrit të lagësht duhet të instalohen në mënyrë që të mos ketë shtresa gjatësore në pjesën e poshtme të kanaleve të ajrit.
Parcela në Kanalet në të cilat vesa mund të bjerë nga ajri i lagësht i transportuar duhet të vendosen me një pjerrësi prej 0,01-0,015 drejt pajisjeve të kullimit.
3.36. Guarnicionet midis fllanxhave të kanaleve të ajrit nuk duhet të dalin në kanalet e ajrit.
Guarnicionet duhet të bëhen nga materialet e mëposhtme:
gome me shkumë, gome kasetë poroze ose monolit me trashësi 4-5 mm ose litar mastik polimer (PMZ) - për kanalet e ajrit nëpër të cilat lëvizin ajri, pluhuri ose materialet e mbeturinave me temperatura deri në 343 K (70 ° C);
kordon asbesti ose karton azbesti - me temperaturë mbi 343 K (70 °C);
gome rezistente ndaj acidit ose plastikë amortizuese rezistente ndaj acidit - për kanalet e ajrit nëpër të cilat lëviz ajri me avujt e acidit.
Dl Për mbylljen e nyjeve vafere të kanaleve të ajrit, duhet të përdoren sa vijon:
G e kasetë mbyllëse "Gerlen" - për kanalet e ajrit përmes të cilave ajri lëviz në temperatura deri në 313 K (40 ° C);
Mastikë Buteprol - për kanalet e rrumbullakëta të ajrit me temperatura deri në 343 K (70 °C);
e tkurrur nga nxehtësiapranga ose shirita - për kanalet e rrumbullakëta të ajrit me temperatura deri në 333 K (60 °C) dhe materiale të tjera mbyllëse të miratuara në përputhje me procedurën e përcaktuar.
3.37. Bulonat në lidhjet me fllanxha duhet të shtrëngohen dhe të gjitha dadot e bulonave duhet të vendosen në njërën anë të fllanxhës. Kur instaloni bulonat vertikalisht, dadot në përgjithësi duhet të vendosen në pjesën e poshtme të bashkimit.
3.38. Mbërthimi i kanaleve të ajrit duhet të kryhet në përputhje me dokumentacionin e punës.
Mbërthimet e kanaleve metalike horizontale jo të izoluara të ajrit (kampa, varëse, mbështetëse, etj.) në një lidhje vafere duhet të instalohen në një distancë prej jo më shumë se 4 m nga njëra-tjetra kur diametri i një kanali të rrumbullakët ose madhësia e ana më e madhe e një kanali drejtkëndor është më pak se 400 mm dhe në një distancë prej jo më shumë se 3 m nga njëra-tjetra - me diametra të një kanali rrethor ose dimensione të anës më të madhe të një kanali drejtkëndor prej 400 mm ose më shumë.
Mbërthimet e kanaleve metalike horizontale të ajrit jo të izoluar në një lidhje fllanxha me një seksion kryq rrethor me diametër deri në 2000 mm ose një seksion kryq drejtkëndor me dimensionet e anës së tij më të madhe deri në 2000 mm përfshirëse duhet të instalohen në distancë. jo më shumë se 6 m nga njëra-tjetra. Distancat midis fiksimeve të kanaleve të ajrit të izoluar metalikë të çdo madhësie prerje tërthore, si dhe kanalet e ajrit jo të izoluar me prerje tërthore të rrumbullakët me një diametër prej më shumë se 2000 mm ose seksion kryq drejtkëndor me dimensione të anës së tij më të madhe më shumë se 2000 mm duhet të përcaktohen si dokumentacion pune.
Kapëset duhet të përshtaten fort rreth kanaleve metalike të ajrit.
Mbërthimet e kanaleve metalike vertikale të ajrit duhet të instalohen në një distancë prej jo më shumë se 4 m nga njëri-tjetri.
Vizatimet e fiksimeve jo standarde duhet të përfshihen në grupin e dokumentacionit të punës.
Mbërthimi i kanaleve vertikale metalike të ajrit brenda ambienteve të ndërtesave shumëkatëshe me lartësi dyshemeje deri në 4 m duhet të kryhet në tavanet e dyshemesë.
Mbërthimi i kanaleve metalike vertikale të ajrit në ambiente të mbyllura me një lartësi dyshemeje më shumë se 4 mm në çatinë e një ndërtese duhet të specifikohet në dizajn (projektim i detajuar).
Nuk lejohet ngjitja e telave dhe varëseve direkt në fllanxhat e kanalit të ajrit. Tensioni i pezullimeve të rregullueshme duhet të jetë uniform.
Devijimi i kanaleve të ajrit nga vertikali nuk duhet të kalojë 2 mm për 1 m gjatësi të kanalit të ajrit.
3.39. Kanalet e ajrit të varur lirisht duhet të mbërthehen duke instaluar varëse të dyfishta çdo dy varëse të vetme me një gjatësi varëseje prej 0,5 deri në 1,5 m.
Për varëse rrobash më të gjata se 1,5 m, duhet të instalohen varëse të dyfishta përmes çdo varëseje të vetme.
3.40. Kanalet e ajrit duhet të përforcohen në mënyrë që pesha e tyre të mos transferohet pajisjet e ventilimit.
Kanalet e ajrit, si rregull, duhet të lidhen me tifozët përmes izolimi i dridhjeve futje fleksibël të bëra nga tekstil me fije qelqi ose materiale të tjera që ofrojnë fleksibilitet, densitet dhe qëndrueshmëri.
Insertet fleksibël që izolojnë dridhjet duhet të instalohen menjëherë përpara testimit individual.
3.41. Kur instaloni kanalet vertikale të ajrit nga asbest-çimento kutitë e fiksimit duhet të instalohen çdo 3-4 m Gjatë instalimit të kanaleve horizontale të ajrit, duhet të instalohen dy fiksim për çdo seksion për lidhjet e bashkimit x dhe një fiksim për lidhjet e prizës. Mbërthimi duhet të bëhet në prizë.
3.42. Në kanalet vertikale të ajrit të bëra nga kanalet e prizës, kanali i sipërm duhet të futet në prizën e asaj të poshtme.
3.43. Në përputhje me grafikët standarde të rrjedhës, lidhjet e prizës dhe bashkimit duhet të mbyllen me fije kërpi të njomur në asbest-çimento tretësirë me shtimin e ngjitësit të kazeinës.
Hapësira e lirë e prizës ose e bashkimit duhet të mbushet asbest-çimento mastikë.
Pasi mastika të jetë ngurtësuar, nyjet duhet të mbulohen me pëlhurë. Pëlhura duhet të përshtatet fort në kutinë rreth gjithë perimetrit dhe duhet të lyhet me bojë vaji.
3.44. Transporti dhe ruajtja në zonën e instalimit të kutive të asbest-çimentos të lidhura me bashkime duhet të kryhet në një pozicion horizontal, dhe kutitë e prizës - në një pozicion vertikal.
Pajisjet nuk duhet të lëvizin lirshëm gjatë transportit, për këtë qëllim ato duhet të sigurohen me ndarës.
Kur mbani, grumbulloni, ngarkoni dhe shkarkoni kuti dhe pajisje, mos i hidhni dhe mos i nënshtroni në goditje.
3.45. Kur bëni seksione të drejta të kanaleve të ajrit nga filmi polimer, kthesat e kanaleve të ajrit lejohen jo më shumë se 15 °.
3.46. Për të kaluar nëpër strukturat mbyllëse, kanali i ajrit i bërë nga filmi polimer duhet të ketë futje metalike.
3.47. Kanalet e ajrit të bërë nga filmi polimer duhet të varen në unaza çeliku të bëra prej teli me diametër 3-4 mm, të vendosura në një distancë prej jo më shumë se 2 m nga njëra-tjetra.
Diametri i unazave duhet të jetë 10% diametër më të madh Kanal ajri. Unazat e çelikut duhet të sigurohen duke përdorur tela ose një pllakë me një prerje në një kabllo mbështetëse (tel) me diametër 4-5 mm, të shtrirë përgjatë boshtit të kanalit të ajrit dhe të siguruar në strukturat e ndërtesës çdo 20-30 m.
Për të parandaluar lëvizjet gjatësore të kanalit të ajrit kur mbushet me ajër, filmi polimer duhet të shtrihet derisa të zhduket plogështia midis unazave.
3.48. Tifozët radialë në bazamentet e dridhjeve dhe në një bazë të ngurtë të instaluar mbi themele duhet të sigurohen me bulona ankorimi.
Kur instaloni ventilatorë në izoluesit e dridhjeve të pranverës, këto të fundit duhet të kenë një sistem të njëtrajtshëm. Izoluesit e dridhjeve nuk kanë nevojë të ngjiten në dysheme.
3.49. Kur instaloni tifozë në strukturat metalike, duhet t'i bashkëngjiten izoluesit e dridhjeve. Elementet e strukturave metalike në të cilat janë ngjitur izoluesit e dridhjeve duhet të përkojnë në plan me elementët përkatës të kornizës së njësisë së ventilatorit.
Kur instalohet në një bazë të ngurtë, korniza e ventilatorit duhet të përshtatet fort me guarnicionet izoluese të zërit.
3.50. Boshllëqet midis skajit të diskut të përparmë të shtytësit dhe skajit të tubit të hyrjes së ventilatorit radial, si në drejtimin boshtor ashtu edhe në atë radial, nuk duhet të kalojnë 1% të diametrit të shtytësit.
Boshtet e ventilatorëve radialë duhet të instalohen horizontalisht (boshtet e ventilatorëve të çatisë duhet të instalohen vertikalisht), dhe muret vertikale të mbështjellësve të ventilatorëve centrifugale nuk duhet të kenë asnjë shtrembërim ose prirje.
Guarnicionet për mbulesat e shumëfishta të tifozëve duhet të bëhen nga i njëjti material si guarnicionet e kanalit për atë sistem.
3.5 1. Motorët elektrikë duhet të jenë në linjë të saktë me ventilatorët e instaluar dhe të siguruar. Akset e rrotullave të motorëve elektrikë dhe tifozëve kur drejtohen nga një rrip duhet të jenë paralele, dhe linjat qendrore të rrotullave duhet të përkojnë.
Rrëshqitjet e motorit elektrik duhet të jenë paralele dhe të nivelit të ndërsjellë. Sipërfaqja mbështetëse e rrëshqitjes duhet të jetë në kontakt përgjatë gjithë rrafshit me themelin.
Lidhjet dhe ngasjet e rripave duhet të mbrohen.
3.52. Hapja e thithjes së ventilatorit, e pa lidhur me kanalin e ajrit, duhet të mbrohet me një rrjetë metalike me madhësi rrjetë jo më shumë se 70´ 70 mm.
3.53. Materiali i filtrit të filtrave të pëlhurës duhet të tendoset pa u varur ose rrudha, dhe gjithashtu të përshtatet fort në muret anësore. Nëse ka lesh në materialin e filtrit, ky i fundit duhet të vendoset në anën e marrjes së ajrit.
3.54. Ngrohësit e kondicionerit duhet të montohen në guarnicione të bëra prej fletësh dhe asbesti me kordon. Blloqet e mbetura, dhomat dhe njësitë e kondicionerëve duhet të montohen në guarnicione të bëra nga shirita gome 3-4 mm të trasha, të furnizuara së bashku me pajisjen.
3.55. Kondicionerët duhet të instalohen horizontalisht. Muret e dhomave dhe blloqeve nuk duhet të kenë gërvishtje, shtrembërime ose pjerrësi.
Tehet e valvulave duhet të rrotullohen lirshëm (me dorë). Në pozicionin "Mbyllur", duhet të sigurohet përshtatja e ngushtë e teheve me ndalesat dhe me njëri-tjetrin.
Mbështetësit e njësive të dhomës dhe njësive të kondicionerit duhet të instalohen vertikalisht.
3.56. Kanalet fleksibël të ajrit duhet të përdoren në përputhje me projektin (dizajni i detajuar) si pajisje për kompleksin formë gjeometrike, si dhe për lidhjen me pajisjet e ventilimit, shpërndarësit e ajrit, shtypësit e zhurmës dhe të tjerë për ndërtesat e vendosura në tavane dhe dhoma të rreme.
4. TESTIMI I SISTEMEVE TË BRENDSHME SANITARE
DISPOZITA TË PËRGJITHSHME PËR TESTIMIN E SISTEMEVE TË FURNIZIMIT TË UJËS TË FTOHTË DHE TË NXEHTË, Ngrohjes, FURNIZIMIT TË NXEHTËSISË, KANALIZIMEVE, KULLIMIT DHE KALADAVE
4.1. Pas përfundimit të punës së instalimit, organizatat e instalimit duhet të kryejnë:
testimi i sistemeve të ngrohjes, furnizimit me ngrohje, furnizimit të brendshëm me ujë të ftohtë dhe të nxehtë dhe dhomave të bojlerit duke përdorur metodën hidrostatike ose manometrike me hartimin e një raporti në përputhje me atë të detyrueshëm, si dhe sistemet e shpëlarjes në përputhje me kërkesat e këtyre rregullave;
testimi i sistemeve të brendshme të kanalizimeve dhe kullimit me hartimin e një raporti në përputhje me detyrimin;
testet individuale të pajisjeve të instaluara me hartimin e një raporti në përputhje me të detyrueshmen;
Testimi termik i sistemeve të ngrohjes për ngrohje uniforme të pajisjeve të ngrohjes.
Testimi i sistemeve që përdorin tubacione plastike duhet të kryhet në përputhje me kërkesat e CH 478-80.
Testet duhet të kryhen përpara fillimit të punës së mbarimit.
Matësit e presionit të përdorur për testim duhet të kalibrohen në përputhje me GOST 8.002-71.
4.2. Gjatë testimit individual të pajisjeve, duhet të kryhet puna e mëposhtme:
kontrollin e përputhshmërisë së pajisjeve të instaluara dhe punës së kryer me dokumentacionin e punës dhe kërkesat e këtyre rregullave;
pajisjet e testimit në gjendje boshe dhe nën ngarkesë për 4 orë funksionim të vazhdueshëm. Në të njëjtën kohë, balancimi i rrotave dhe rotorëve në asambletë e pompës dhe shkarkimit të tymit, cilësia e paketimit të kutisë së mbushjes, shërbimi i pajisjeve të ndezjes, shkalla e ngrohjes së motorit elektrik dhe pajtueshmëria me kërkesat për montim dhe instalim. kontrollohen pajisjet e specifikuara në dokumentacionin teknik të prodhuesve.
4.3. Testimi hidrostatik i sistemeve të ngrohjes, sistemeve të furnizimit me ngrohje, kaldajave dhe ngrohës uji duhet të kryhet në një temperaturë pozitive në ambientet e ndërtesës, dhe për sistemet e furnizimit me ujë të ftohtë dhe të nxehtë, kanalizimet dhe kanalizimet - në një temperaturë jo më të ulët se 278 K (5 ° C). Temperatura e ujit gjithashtu nuk duhet të jetë më e ulët se 278 K (5 °C).
SISTEMET E BRENDSHME TË FURNIZIMIT TË UJËS TË FTOHTË DHE TË NXHET
4.4. Sistemet e brendshme të furnizimit me ujë të ftohtë dhe të nxehtë duhet të testohen me metodën hidrostatike ose manometrike në përputhje me kërkesat e GOST 24054-80, GOST 25136-82 dhe këto rregulla.
Vlera e presionit të provës për metodën e provës hidrostatike duhet të merret e barabartë me 1,5 presion të tepërt të funksionimit.
Testimi hidrostatik dhe presioni i sistemeve të furnizimit me ujë të ftohtë dhe të nxehtë duhet të kryhet përpara instalimit të çezmave të ujit.
Sistemet konsiderohen se i kanë kaluar testet nëse, brenda 10 minutave nga të qenit nën presionin e provës duke përdorur metodën e provës hidrostatike, nuk ka rënie presioni prej më shumë se 0,05 MPa (0,5 kgf/cm 2) dhe rënie në saldime, tuba, lidhjet me fileto, pajisje dhe rrjedhje uji përmes pajisjeve shpëlarëse.
Në fund të testit hidrostatik, është e nevojshme të lirohet uji nga sistemet e brendshme të furnizimit me ujë të ftohtë dhe të nxehtë.
Sistemi konsiderohet se e ka kaluar testin nëse, kur është nën presionin e provës, rënia e presionit nuk kalon 0,01 MPa (0,1 kgf/cm2).
SISTEMET E NGROHJES DHE FURNIZIMIT ME Ngrohje
4.6. Testimi i sistemeve të ngrohjes së ujit dhe furnizimit me nxehtësi duhet të kryhet me kaldaja dhe enët e zgjerimit të fikur duke përdorur metodën hidrostatike me një presion të barabartë me 1,5 presion pune, por jo më pak se 0,2 MPa (2 kgf/cm2) në pikën më të ulët të sistemi.
Sistemi konsiderohet se e ka kaluar testin nëse, brenda 5 minutave pasi është nën presionin e provës, rënia e presionit nuk i kalon 0,02 MPa (0,2 kgf/cm) dhe nuk ka rrjedhje në saldime, tuba, lidhje me fileto, pajisje, ngrohje. pajisjet dhe pajisjet.
Vlera e presionit të provës duke përdorur metodën e provës hidrostatike për sistemet e ngrohjes dhe furnizimit me ngrohje të lidhur me një impiant ngrohjeje nuk duhet të kalojë presionin maksimal të provës për pajisjet e ngrohjes dhe pajisjet e ngrohjes dhe ventilimit të instaluara në sistem.
4.7. Testet manometrike të sistemeve të ngrohjes dhe furnizimit me ngrohje duhet të kryhen në sekuencën e specifikuar në.
4.8. Sistemet e ngrohjes sipërfaqësore duhet të testohen, zakonisht duke përdorur metodën hidrostatike.
Testimi manometrik mund të kryhet në temperatura negative të jashtme.
Testimi hidrostatik i sistemeve të ngrohjes së paneleve duhet të kryhet (para mbylljes së dritareve të instalimit) me presion 1 MPa (10 kgf/cm2) për 15 minuta, ndërsa rënia e presionit lejohet të jetë jo më shumë se 0,01 MPa (0,1 kgf/ cm2).
Për sistemet e ngrohjes me panele të kombinuara me pajisjet e ngrohjes, vlera e presionit të provës nuk duhet të kalojë presionin maksimal të provës për pajisjet e ngrohjes të instaluara në sistem.
Vlera e presionit të testimit të sistemeve të ngrohjes së paneleve, sistemeve të ngrohjes me avull dhe furnizimit me nxehtësi gjatë testeve manometrike duhet të jetë 0,1 MPa (1 kgf/cm2). Kohëzgjatja e testit - 5 minuta. Rënia e presionit nuk duhet të jetë më shumë se 0,01 MPa (0,1 kgf/cm2).
4.9. Sistemet e ngrohjes me avull dhe furnizimit me nxehtësi me presion pune deri në 0,07 MPa (0,7 kgf/cm2) duhet të testohen me metodën hidrostatike me presion të barabartë me 0,25 MPa (2,5 kgf/cm2) në pikën më të ulët të sistemit; sisteme me presion pune më shumë se 0,07 MPa (0,7 kgf/cm 2) - presion hidrostatik i barabartë me presionin e punës plus 0,1 MPa (1 kgf/cm 2), por jo më pak se 0,3 MPa (3 kgf/cm 2) në pika kryesore e sistemit.
Sistemi njihet se e ka kaluar testin e presionit nëse, brenda 5 minutave pasi është nën presionin e provës, rënia e presionit nuk i kalon 0,02 MPa (0,2 kgf/cm2) dhe nuk ka rrjedhje në saldime, tuba, lidhje me fileto, pajisje, pajisjet e ngrohjes
Sistemet e ngrohjes me avull dhe furnizimit me nxehtësi, pas testimit hidrostatik ose presionit, duhet të kontrollohen duke ndezur avullin në presionin e funksionimit të sistemit. Në këtë rast, rrjedhjet e avullit nuk lejohen.
4.10. Testimi termik i sistemeve të ngrohjes dhe furnizimit me ngrohje në temperatura pozitive të ajrit të jashtëm duhet të kryhet në një temperaturë uji në linjat e furnizimit të sistemeve të paktën 333 K (60 °C). Në këtë rast, të gjitha pajisjet e ngrohjes duhet të ngrohen në mënyrë të barabartë.
Nëse nuk ka burime nxehtësie gjatë sezonit të ngrohtë, duhet të kryhet një test termik i sistemeve të ngrohjes pas lidhjes me një burim nxehtësie.
Testimi termik i sistemeve të ngrohjes në temperatura negative të ajrit të jashtëm duhet të kryhet në një temperaturë të ftohësit në tubacionin e furnizimit që korrespondon me temperaturën e ajrit të jashtëm gjatë testimit sipas planit të temperaturës së ngrohjes, por jo më pak se 323 K (50 °C), dhe presioni qarkullues në sistem sipas dokumentacionit të punës.
Testimi termik i sistemeve të ngrohjes duhet të kryhet brenda 7 orëve, duke kontrolluar uniformitetin e ngrohjes së pajisjeve të ngrohjes (në prekje).
KAZADITË
4.11. Kaldaja duhet të testohet duke përdorur metodën hidrostatike përpara punimeve të rreshtimit dhe ngrohës uji- para aplikimit të termoizolimit. Gjatë këtyre testeve, tubat e ngrohjes dhe furnizimit me ujë të ngrohtë duhet të shkëputen.
Pas përfundimit të testeve hidrostatike, është e nevojshme të lirohet uji nga kaldaja dhe ngrohës uji.
Kaldaja dhe ngrohësit e ujit duhet të testohen nën presion hidrostatik së bashku me pajisjet e instaluara në to.
Përpara testimit hidrostatik të bojlerit, kapakët dhe çelësat duhet të mbyllen fort, valvulat e sigurisë të bllokohen dhe duhet të vendoset një prizë në lidhjen me fllanxha të pajisjes rrjedhëse ose bypass-in më afër bojlerit me avull.
Vlera e presionit të provës për testet hidrostatike të kaldajave dhe ngrohësve të ujit pranohet në përputhje me standardet ose kushtet teknike për këtë pajisje.
Presioni i provës mbahet për 5 minuta, pas së cilës zvogëlohet në presionin maksimal të funksionimit, i cili mbahet për të gjithë kohën e nevojshme për të inspektuar bojlerin ose ujëngrohës.
Kaldaja dhe ngrohës uji njihen se kanë kaluar testin hidrostatik nëse:
gjatë kohës që ata ishin nën presionin e provës, nuk u vu re asnjë rënie e presionit;
nuk u gjet gruaja ka shenja këputjeje, rrjedhjeje dhe djersitjeje të sipërfaqes.
4.12. Tubacionet e karburantit duhet të testohen me një presion hidrostatik prej 0,5 MPa (5 kgf/cm2). Sistemi konsiderohet se e ka kaluar provën nëse, brenda 5 minutave pasi është nën presionin e provës, rënia e presionit nuk kalon 0,02 MPa (0,2 kgf/cm2).
KANALIZIMET E BRENDSHME DHE KULLIMET
4.13. Testimi i sistemeve të kanalizimeve të brendshme duhet të kryhet duke derdhur ujë duke hapur njëkohësisht 75% të pajisjeve sanitare të lidhura me zonën që testohet për kohën e nevojshme për inspektimin e tij.
Sistemi konsiderohet të ketë kaluar testin nëse, gjatë inspektimit të tij, nuk u zbuluan rrjedhje nëpër muret e tubacioneve dhe nyjeve.
Provat e tubacioneve të daljes së kanalizimeve të vendosura në kanalet tokësore ose nëntokësore duhet të kryhen përpara se të mbyllen duke i mbushur me ujë deri në nivelin e katit përdhes.
4.14. Testet në seksionet e sistemeve të kanalizimeve të fshehura gjatë punës së mëvonshme duhet të kryhen duke derdhur ujë përpara se të mbyllen, me hartimin e një raporti inspektimi për punën e fshehur në përputhje me Shtojcën 6 të detyrueshme. SNiP 3.01.01-85.
4.15. Kullimet e brendshme duhet të testohen duke i mbushur me ujë në nivelin më të lartë. hinkë kullimi. Kohëzgjatja e testit duhet të jetë së paku 10 minuta.
Kullimet konsiderohen të kenë kaluar testin nëse nuk konstatohen rrjedhje gjatë inspektimit dhe niveli i ujit në ngritës nuk është ulur.
AJERIMI DHE KONDICIONI
4.16. Faza përfundimtare e instalimit të sistemeve të ventilimit dhe ajrit të kondicionuar është testimi i tyre individual.
Me fillimin e testimit individual të sistemeve, duhet të përfundojë puna e përgjithshme e ndërtimit dhe mbarimit të dhomave dhe boshteve të ventilimit, si dhe instalimi dhe testimi individual i pajisjeve mbështetëse (energjia elektrike, furnizimi me ngrohje dhe ftohje dhe etj.). Nëse nuk ka furnizim me energji elektrike për njësitë e ventilimit dhe ajrit të kondicionuar sipas një skeme të përhershme, kontraktori i përgjithshëm do të lidhë energjinë elektrike sipas një skeme të përkohshme dhe do të kontrollojë shërbimin e pajisjeve fillestare.
4.17. Gjatë testeve individuale, organizatat e instalimit dhe ndërtimit duhet të kryejnë punën e mëposhtme:
kontrolloni përputhshmërinë e ekzekutimit aktual të sistemeve të ventilimit dhe ajrit të kondicionuar me projektin (projektimin e detajuar) dhe kërkesat e këtij seksioni;
kontrolloni seksionet e kanalit të ajrit të fshehur nga strukturat e ndërtimit për rrjedhje duke përdorur teste aerodinamike sipas GOST 12.3.018-79, bazuar në rezultatet e testit të rrjedhjes, hartoni një raport inspektimi për punën e fshehur në formën e Shtojcës 6 të detyrueshme SNiP 3.01.01-85;
testoni (fun në punë) pajisjet e ventilimit me një makinë, valvola dhe amortizues në boshe, në përputhje me kërkesat e përcaktuara nga specifikimet teknike të prodhuesve.
Kohëzgjatja e futjes merret sipas Specifikimet teknike ose pasaportën e pajisjes që testohet. Bazuar në rezultatet e testeve (përdorimit) të pajisjeve të ventilimit, hartohet një raport në formën e detyrueshme.
4.18. Kur rregulloni sistemet e ventilimit dhe ajrit të kondicionuar për parametrat e projektimit duke marrë parasysh kërkesat e GOST 12.4.021-75, duhet të bëhen sa më poshtë:
testimi i tifozëve kur funksionon në një rrjet (përcaktimi i përputhshmërisë së karakteristikave aktuale me të dhënat e pasaportës: furnizimi dhe presioni i ajrit, shpejtësia e rrotullimit, etj.);
kontrollimi i uniformitetit të ngrohjes (ftohjes) të shkëmbyesve të nxehtësisë dhe kontrolli i mungesës së largimit të lagështirës përmes eliminatorëve të pikave të dhomave të ujitjes;
provë f dhe rregullimin e sistemeve me qëllim arritjen e treguesve të projektimit për rrjedhën e ajrit në kanalet e ajrit, thithjen lokale, shkëmbimin e ajrit në dhoma dhe përcaktimin e thithjes ose humbjeve të ajrit në sisteme, vlera e lejueshme e të cilave për shkak të rrjedhjeve në kanalet e ajrit dhe elementëve të tjerë të sistemet nuk duhet të kalojnë vlerat e projektimit në përputhje me SNiP 2.04.05-85;
kontrollimi i funksionimit të pajisjeve të shkarkimit të ventilimit natyror.
Për çdo sistem ventilimi dhe kondicionimi lëshohet një pasaportë në dy kopje në formën e detyrueshme.
4.19. Devijimet e normave të rrjedhës së ajrit nga ato të parashikuara në projekt pas rregullimit dhe testimit të sistemeve të ventilimit dhe ajrit të kondicionuar lejohen:
± 10 % - bazuar në rrjedhën e ajrit që kalon nëpër shpërndarjen e ajrit dhe hyrjet e ajrit instalimi i instalimeve të ventilimit të përgjithshëm dhe të ajrit të kondicionuar, me kusht që të sigurohet presioni i kërkuar i ajrit (rrallimi) në dhomë;
10 % - bazuar në konsumin e ajrit të hequr përmes thithjes lokale dhe të furnizuar përmes tubave të dushit.
4.20. Gjatë testimit gjithëpërfshirës të sistemeve të ventilimit dhe ajrit të kondicionuar, puna e vënies në punë përfshin:
testimi i sistemeve operative në të njëjtën kohë;
kontrollimi i funksionalitetit të ventilimit, ajrit të kondicionuar dhe furnizimi me ngrohje dhe ftohje në kushtet e funksionimit të projektimit me përcaktimin e përputhshmërisë së parametrave aktualë me ato të projektimit;
identifikimi i arsyeve pse nuk sigurohen mënyrat e funksionimit të projektimit të sistemeve dhe marrja e masave për eliminimin e tyre;
testimi i pajisjeve mbrojtëse, bllokimit, alarmeve dhe pajisjeve të kontrollit;
matjet e niveleve të presionit të zërit në pikat e projektimit.
Testimi gjithëpërfshirës i sistemeve kryhet sipas programit dhe orarit të zhvilluar nga klienti ose në emër të tij nga organizata komisionere dhe të rënë dakord me kontraktorin e përgjithshëm dhe organizatën e instalimit.
Procedura për kryerjen e testimit gjithëpërfshirës të sistemeve dhe eliminimin e defekteve të identifikuara duhet të përputhet me SNiP III -3 - 81.
ANEKSI 1
E detyrueshme
AKT
|
Parimi i funksionimit të kanalizimeve të gravitetit bazohet në lëvizjen e lëngjeve dhe përzierjeve të pezulluara midis lartësive të ndryshme. Praktikisht kjo realizohet me vendosjen e tubave të kanalizimeve me pjerrësi. Duhet mbajtur mend se SNiP rregullon qartë pjerrësinë e tubit të kanalizimeve për kushte të ndryshme përdorimi.
Me një ulje të këndit të prirjes, gjithçka është e qartë - kjo çon në një ulje të shpejtësisë së lëvizjes së lëngut, gjë që shkakton rritje të depozitimit të yndyrave dhe substancave të tjera në muret e tubave. Në fund, Nëse pastrimi parandalues i sistemit nuk kryhet, ndodhin bllokime të kanalizimeve.
Por papranueshmëria e rritjes së këndit të prirjes shkakton hutim tek shumë; duket se diçka nuk është në rregull me këtë; uji do të thahet më shpejt. Rezulton se pikërisht këtu qëndron përgjigja e pyetjes.
Rritja e shpejtësisë së lëvizjes çon në një efekt pozitiv vetëm për lëngjet. Ujërat e zeza janë një përzierje e lëngshme dhe e ngurtë.
Ndërsa shpejtësia e lëvizjes së përzierjes rritet, do të shfaqet fotografia e mëposhtme: fraksioni i lëngshëm do të rrjedhë i sigurt me shpejtësi të lartë dhe trupat e ngurtë do të mbeten në tub, gjë që me kalimin e kohës gjithashtu çon në bllokim.
Prandaj, pjerrësia maksimale për kanalizimet është e rregulluar qartë, nuk duhet të kalojë 15 cm për 1 metër (0.15). Përjashtim bëjnë degët, gjatësia e të cilave është më pak se 1.5 metra.
|
Llogaritja e pjerrësisë së kërkuar
Më shpesh, kur përcaktohet pjerrësia e kanalizimeve, përdoren standarde të qarta SNiP; kjo metodë quhet jo-llogaritje. Por kur instaloni sisteme komplekse të kanalizimeve, ndonjëherë është e nevojshme të drejtoheni në llogaritjet speciale, dhe kjo metodë përdoret gjithashtu kur ekziston nevoja reale për të zvogëluar pjerrësinë (ndonjëherë një nevojë e tillë lind për arsye teknike).
Në këtë rast, përcaktohet devijimi maksimal i lejuar nga standardi. Llogaritja bëhet duke përdorur formula të veçanta, rezultati i saj varet nga shpejtësia e lëngut, diametri dhe shkalla e mbushjes së tubacionit. Por, përsëri, e përsërisim, nevoja për llogaritje të tilla lind rrallë.
Këndi i pjerrësisë për kanalizimet e brendshme
Gjatë instalimit të kanalizimeve të brendshme, duhet të respektohen kushtet e mëposhtme.
Siç është përmendur tashmë, dokumenti kryesor që rregullon pjerrësinë e tubave të kanalizimeve është SNiP.
Sipas SNiP, pjerrësia minimale për tubat me diametër 50 mm duhet të jetë 0.03, për tubat 110 mm, pjerrësia duhet të jetë së paku 0.02.
Janë këto tuba që përdoren gjatë instalimit të kanalizimeve të brendshme. Gjatë instalimit, këshillohet të shmangni kthimin në kënd të drejtë në çdo plan, më e mira për të aplikuar lidhje serike disa kthesa me një kënd më të vogël.
Nëse kjo nuk është e mundur, atëherë është e nevojshme të instalohen rishikime (pastrim) në vende të tilla. Të gjithë elementët e kanalizimit duhet të fiksohen mirë; fiksimi kryhet duke përdorur kapëse speciale, hapi i instalimit të të cilave është i barabartë me 10 diametra tubash.
Kanalizimet e brendshme duhet të jenë të pajisura me ventilim të ventilimit. Ajo jo vetëm që do të shpëtoj aromat e mundshme, por gjithashtu do të sigurojë funksionimin normal të sistemit pa ndërprerje të izolimit të ujit.
Tubi i ventilatorit duhet të vendoset vertikalisht pa devijime. Por në shtëpi private, ndonjëherë, për arsye teknike, është e nevojshme të instalohen seksione horizontale. Ato duhet të bëhen me një pjerrësi të vogël.
Ku pjerrësia e tubit të kullimit duhet të drejtohet drejt sistemit. Kjo është bërë në mënyrë që kondensimi ose reshjet që futen në tub të rrjedhin në kanalizim dhe të mos ngecin.
Pjerrësi për kanalizim të jashtëm
Për instalimin e kanalizimeve të jashtme në Kushtet e jetesës Më shpesh, përdoren tuba me një diametër prej 110 deri në 200 mm. Pjerrësia minimale Tubi i kanalizimeve, sipas rekomandimeve të SNiP, është:
- për tuba me diametër 110 mm - 0.03;
- 160 mm - 0,008;
- 200 mm - 0,007.
Gjatë instalimit, duhet t'i përmbaheni rregullave të mëposhtme.
Linja e kanalizimit duhet të vendoset në një thellësi që mund të jetë 30 cm më e vogël se niveli i ngrirjes së tokës.Nëse i vendosni tubat më lart, do të kërkohet termoizolim shtesë.
Kur kryeni punë gërmimi, gërmoni një kanal, është e nevojshme të mbani mend pjerrësinë e ardhshme të sistemit, kështu që fundi i kanalit duhet të thellohet në përputhje me rrethanat.
Thellësia e hendekut duhet të jetë 20-30 cm më e madhe se niveli i shtrimit të tubit, nëse është më i thellë, atëherë mbulohet me përzierje dheu dhe rëre me ngjeshje të detyrueshme. Do të jetë e përshtatshme të rregulloni nivelin e hendekut duke përdorur një varg të shtrirë në nivelin e kërkuar.
Së fundi, shtrati nën tub, dhe, në përputhje me rrethanat, pjerrësia e sistemit të kanalizimit të jashtëm, formohet duke përdorur një jastëk rërë, mbi të cilin sistemi është montuar drejtpërdrejt.
Tubat e kanalizimeve janë instaluar me një prizë përballë rrjedhës, kjo do të sigurojë ngushtësi maksimale.
Nëse është e nevojshme të shkurtoni tubin, prerja bëhet me një sharrë hekuri të thjeshtë dhe një zgavër hiqet përgjatë skajit të prerjes. Këmbana nuk mund të pritet.
I gjithë materiali i përdorur nuk duhet të ketë të çara, patate të skuqura ose thyerje. Përndryshe, sistemi do të lyhet vazhdimisht.
Në vendet ku ka dallime në nivel dhe kthesa të linjave, instalohen puse speciale.
Pas montimit dhe vendosjes së tubave në shtrat, është e nevojshme të kontrollohet niveli i tubave. Nëse është e nevojshme, shtohet shtroja; duhet të mbulojë tubin me të paktën një të tretën, dhe tubat duhet të shtrihen fort; boshllëqet nën to nuk lejohen. Kjo është mënyra e vetme për të formuar shpatet optimale kanalizimet.
Pas rregullimit përfundimtar, është e nevojshme të mbushni tubin, dhe së pari mbulohet me rërë, kjo do të mbrojë sistemin nga dëmtimet nga rënia e tufave të tokës. Pas kësaj, kanali mund të mbushet duke përdorur një metodë të mekanizuar.
Pajtueshmëria me teknologjinë për vendosjen e linjave të kanalizimeve, si dhe madhësitë e rekomanduara nga standardet, është baza për funksionimin normal dhe pa probleme të sistemit. Nuk ka nevojë të mendoni se cilën pjerrësi të tubit të kanalizimeve të zgjidhni. Thjesht hapni SNiP, atje do të gjeni përgjigje për të gjitha pyetjet tuaja.
Materiali më i zakonshëm për rrjetet e kanalizimeve tani janë tubat plastikë të madhësive të ndryshme. Me ndihmën e tyre, ju mund të instaloni lehtësisht një sistem kanalizimi në përputhje me të gjitha kërkesat, dhe lidhja e linjave të tilla me sistemin qendror të kanalizimeve bëhet duke përdorur përshtatës të veçantë.
Tubacionet e kanalizimeve kërkojnë vëmendje shumë të kujdesshme për fjalë për fjalë çdo element.
Vetëm në këtë rast nuk do të lindë nga funksionimi i mëtejshëm. Çdo fazë e punës kryhet në bazë të dokumentacionit aktual rregullator.
Një nga llojet e tij është SNiP. Kanalizime, rrjete te brendshme – vetëm një nga shumë fusha ndërtimi të mbuluara nga ky dokument.
Sistemi i kanalizimit i vendosur jashtë përbëhet nga: tubacionet kryesore, strukturat e kullimit dhe kanalizimeve. Pa rregullim, llojet e tjera të pajisjeve asgjë nuk do të funksionojë.
Mund të ketë disa sisteme instalimi në një sistem të tillë kanalizimesh:
- Krijimi i një aliazh të veçantë. Çdo pjesë e sistemit ka një kolektor të veçantë për kullimin e ujërave të zeza.
- Aliazh gjysëm i ndarë. Dy janë përdorur sisteme të veçanta për reshjet atmosferike, si dhe ujërat e zeza nga aktivitetet sociale dhe ekonomike. Por një kanalizim përdoret për kullim.
- Aliazh i përgjithshëm. Gjithçka është e kombinuar në sistem të unifikuar, i cili përfshin kolektorin.
Pothuajse asnjë nga ato moderne nuk ndërtohet pa parimin e gravitetit. Prandaj, terreni gjithmonë meriton vëmendje të veçantë.
Kërkohet një llogaritje e saktë e pjerrësisë. Kur vendoset një tubacion, roli i mbështetjes luhet nga një dokument si SNiP 2.04.03-85. Nëse nuk e merrni parasysh këtë faktor, atëherë tubacioni thjesht do të bllokohet me grimca, përfshirë ato të ngurta:
- Nëse pjerrësia është shumë e madhe, shkalla e rrjedhës do të rritet. Por për shkak të kësaj, përfshirje të forta do të mbeten në vend.
- Një pjerrësi e vogël çon në një ulje të cilësisë së kullimit. Si rezultat, grimcat e ngurta vendosen në tuba. Dhe krijohen bllokime.
0,7-1 m/s është shpejtësia optimale për lëvizjen e transportuesit brenda. Kjo është ajo që thotë në të gjitha llojet e SNiP. Instalimi i kanalizimeve dhe rrjeteve të brendshme kryhet vetëm duke marrë parasysh këto kërkesa.
Instalimi i rrjeteve të brendshme
Procesi kërkon shumë kohë, edhe me vëmendje të kujdesshme për çdo hap.
Pa ndjekur një sekuencë të caktuar, nuk do të jetë e mundur të arrihet rezultati i dëshiruar.
Si dhe pa tërësi dhe saktësi.
Performanca e të gjithë sistemit varet nga sa me kompetencë është kryer.
Ndihma profesionale është e pazëvendësueshme, edhe pse është e mundur të kryeni vetë një pjesë të punës.
Dokumenti i detyrueshëm për rishikim do të jetë SNiP "Furnizimi me ujë dhe kanalizimet e brendshme".
Edhe nëse e përgatisni vetë projektin, rekomandohet t'ia tregoni këtë të fundit një specialisti. Atëherë ka më pak shanse që të shfaqen probleme në të ardhmen. Vetëm pas miratimit mund të filloni të blini ato të kërkuara.
Ne fillojmë me instalimin e ngritësve
Kjo është faza e parë në procesin e instalimit të ngritësve. Sipas planit të zhvilluar, shenjat aplikohen në sipërfaqe. Vetëm pas kësaj ata fillojnë të instalojnë tubacionin.
Pozicionet vertikale të ngritësve duhet të respektohen me rigorozitet maksimal. Atëherë nuk do të ketë thyerje apo shtrembërime në vendet ku janë bashkuar tubat.
Tubat janë vendosur në mënyrë që bazat të drejtohen lart. Ata fillojnë duke filluar punën në bodrumet. Në të njëjtën kohë, ata po përpiqen të organizojnë një auditim.
Çfarë është një auditim, pse është i nevojshëm? Ky është emri i një lloji tee ose montimi. Është e nevojshme për të siguruar akses të lirë në pjesët e tubacionit ku mund të shfaqet një boshllëk.
Ata përpiqen të instalojnë rishikime në çdo vend ku shfaqet një cep. Dhe gjithashtu në fillim, në fund.
Për një tubacion linear dhe të gjatë, 30 centimetra është distanca minimale midis pajisjeve. Rekomandohet që ata që planifikojnë të krijojnë një formë ngritëse me tela të kujdesen për kapakun e inspektimit. Çelje të tilla nevojiten për të lehtësuar mirëmbajtjen e furnizimit me ujë.
Ventilimi është ajo me të cilën përfundon domosdoshmërisht secila nga ngritësit e kanalizimeve. Duhet të futet në papafingo me ventilim të mirë. Ose në çatinë e një shtëpie.
Në fund të kanalit struktura duket si kanal ventilimi, me ndertim individual. Ndalohet rreptësisht kalimi i komunikimeve në pjesën e oxhakut të ndërtesës; kjo nuk do të lejojë respektimin e të gjitha rregullave të sigurisë.
Linjat horizontale të degëve janë instaluar në të njëjtën kohë me vetë ngritësit. Kjo vlen për çdo kat të ndërtesës.
Prizat nuk duhet të vendosen në vende ku kalojnë ndërtim ndërtimi si tavanet.
Rreth punës së instalimit, metodave të lidhjes së tubave
Seksionet e vogla të tubacionit mund të montohen lehtësisht në vendin e duhur nëse blerësi preferon llojet plastike të tubave.
Vetëm pas montimit ata fillojnë instalimin e drejtpërdrejtë.
Përdorimi i guarnicioneve të gomës ndihmon në mbylljen e elementeve lidhës.
Seksionet e tubave të bëra prej gize kanë lidhjet më komplekse.
Mbërthimet lejohen si në grupet e prizës ashtu edhe në grupin e bashkimit.
Secila prej tyre ka karakteristikat e veta:
- Lloji i prizës është më i thjeshtë. Një pjesë e tubacionit thjesht futet në një tjetër, përmes të ashtuquajturave priza. Lidhja mbyllet duke përdorur unaza speciale gome. Më pas përdorin kërpin dhe çdo gjë sipër e lyejnë me bitum. Ose duke përdorur llaç çimentoje.
- Puna me nyje bashkuese konsiderohet më intensive. Ato përdoren shumë më rrallë, sepse kërkojnë domosdoshmërisht përdorimin e aftësive të veçanta.
Edhe zejtarët fillestarë mund të përballojnë instalimin e kanalizimeve plastike.
- Në njërën skaj të tubit ka një fund mbyllës me një bashkim, në anën tjetër ka një prerje të vogël me një zgavër.
- Tubi futet në bashkim derisa të ndalojë. Dhe pastaj tërhiqet, por vetëm një centimetër e gjysmë.
- Sistemi fiton ngushtësi shtesë falë unazave të gomës.
- Ku ka një lidhje, shfaqen portat e damperit. Kjo siguron mbrojtje shtesë kundër zgjerim linear në tuba. Kjo thuhet gjithashtu në dokumente të tilla si SNiP. Kanalizime, rrjete te brendshme, pastrim – çdo gjë duhet të jetë në përputhje me kërkesat e standardit.
Ekziston grupi i mëposhtëm i dispozitave të rregulluara nga dokumenti:
- Për tubat, rrafshi horizontal është i rëndësishëm. Nëse drejtimi duhet të ndryshohet, përdoren elementë të veçantë lidhës.
- Llojet e degëve të tubacioneve janë ngjitur në ngritës me majë dhe kryqe.
- Një pozicion i hapur i sistemit të kanalizimit në bodrum dhe në dhomat e shërbimeve është i pranueshëm. Elementet speciale ndihmojnë në montimin në mure. Në panelet dhe muret e strukturës, nën dysheme, tubat janë të vendosura vetëm të fshehura. Pastaj kalojnë në krijimin e brazdave të fshehura.
- Fino me bazë çimento do të ndihmojë në mbylljen e zonave ku tubat takohen me dyshemetë.
- Nuk lejohet vendosja e linjave të kullimit në dysheme, mure apo tavane të dhomave të ndenjes. Kjo vlen edhe për kuzhinat dhe çdo ambient ku kërkohet një regjim i veçantë sanitar.
- Çelësat janë instaluar në anën e kundërt nga inspektimet. Pikërisht në ngritës.
- Komunikimet për tualete dhe banja janë të vendosura mbi mbulesat e dyshemesë. Gjëja kryesore është që së pari të kujdeseni për hidroizolimin.
Ngritës i kanalizimeve. Me çfarë rregullash përcaktohet?
Ne kemi shkruar tashmë për rishikimet më lart. Edhe vendndodhjet e elementeve të tillë janë të rregulluara në SNiP.
- Ato instalohen në katin e parë dhe të fundit të ndërtesës nëse nuk ka dhëmbëzime në ngritëset.
- Kur lidhni tubat me tre ose më shumë pajisje pa pajisje pastrimi, instalimi kryhet në fillim të seksionit me strukturat e daljes.
- Ato duhet të instalohen në të gjitha kthesat.
- Distanca midis rishikimeve duhet të jetë së paku 8 metra. Ky rregull është i përgjithshëm për të gjitha zonat në rrafshin horizontal.
Sistemet e ujërave të zeza dhe ventilimi i tyre
Për të organizuar ventilimin, duhet të instaloni ngritës të veçantë. Ata kalojnë të gjithë. Asnjë ngritës i vetëm i kullimit nuk mund të bëjë pa pajisje ventilimi. Vetë sistemi është i nevojshëm për të zgjidhur tre probleme të ndryshme:
- Reduktimi i zhurmës së jashtme.
- Ruan presionin në një nivel konstant.
- Duke hequr qafe erën.
Tubi i ventilimit duhet të ketë të njëjtin diametër me ngritësin. Ose më i madh. Pjesa e shkarkimit nuk mund të kombinohet me oxhakun dhe sistemin e ventilimit.
Kur kulloni ujin, ajri rrallohet nëse nuk ka ventilim në sistem. Për shkak të kësaj, aromat e pakëndshme shfaqen në ambiente të mbyllura.
SNiP-të gjithashtu përshkruajnë në detaje se cila duhet të jetë lartësia e ventilimit mbi çati.
- 3 metra - mbi çatinë në përdorim.
- 0,5 metra - për një çati të pjerrët.
- 0,3 metra - për një çati të sheshtë që nuk përdoret në mënyrë aktive.
Duhet të ketë të paktën 0.1 metra në boshtin e parafabrikuar të ventilimit.
Cilat tuba duhet të përdor dhe si?
Tuba, sipas të njëjtave SNiP, zgjidhen bazuar në kërkesat për ngurtësinë dhe aftësinë për t'i rezistuar proceseve korrozive.
Ju nuk mund të bëni pa marrë parasysh aftësitë financiare. Përdorimi i pranueshëm materiale të ndryshme, gjëja kryesore është pajtueshmëria me preferencat e atyre që e zotërojnë atë.
Sistemi i brendshëm i kanalizimit furnizohet me:
- Sistemi i presionit. Ai përbëhet nga gypa plastike, gize, asbest-çimento dhe betonarme.
- Sistemi i gravitetit. Këtu përdorin qelq dhe plastikë, gize, asbest çimento, beton, tipe te ndryshme betonarme.
Gjithnjë e më shumë blerës preferojnë plastikën. Falë këtë material ata marrin shumë përfitime:
- Çmontim i shpejtë kur është e nevojshme.
- Mirëmbajtje e lehtë. Riparimet në linjë nuk do të shkaktojnë asnjë problem.
- Niveli i lartë i rezistencës ndaj bllokimeve.
- Qëndrueshmëria.
- Besueshmëria.
- Aftësia për t'i rezistuar ndikimeve mjedisore.
- Mbrojtja ndaj reagentëve kimikë.
- Nuk ka procese korrozioni.
- Instalim i shpejtë dhe i lehtë.
- Niveli i çmimeve për produktet mbetet i ulët.
Për prodhimin e tubacioneve, pajisjeve dhe përbërësve, lejohet të përdoren të njëjtat materiale.
Lidhja elektrike kryhet me tuba plastikë të disa varieteteve. Nga të gjitha materialet karakteristikat më të mira ndryshojnë:
- Polipropileni.
- Polietileni.
Shumica e tubave të kullimit përdorin këto materiale. Disa instalojnë produkte të bëra nga klorur polivinil. Por në këtë rast, karakteristikat e performancës zvogëlohen dukshëm.
Linjat e kullimit. Rreth malit
Përdorimi i kapëseve speciale do të shtojë besueshmërinë e fiksimeve. Mbërthimet janë të vendosura përgjatë gjithë linjës kryesore, kur organizoni prizën përgjatë tuba plastike. Distanca midis tyre është 0,5-1 metra.
Komplete kllapash çeliku me kthesa fundore përdoren për instalim me një diametër prej 100-110 milimetra. Atëherë ka më pak shanse që kanalizimi të zhvendoset për shkak të presionit të lëngut.
Kllapat janë të vendosura nën secilin prej tubave të daljes, pranë prizës.
Cilat janë kërkesat për izolimin e zërit?
Banorët shpesh shqetësohen se është shumë e zhurmshme kur kalon nëpër rrjete. Në shumë mënyra, gjithçka këtu përcaktohet nga materialet e përdorura në prodhimin e tubave në rrjetet e brendshme të kanalizimeve.
Ky problem zgjidhet lehtësisht falë dy të mëposhtmeve:
- Instaloni tubacione të bazuara në polipropilen të mineralizuar. Kjo siguron thithjen e mirë të zhurmës. Konsumi serioz i energjisë nuk kërkohet për të kryer një punë të tillë. Ka shume zgjidhje të gatshme, ku pothuajse të gjithë elementët janë montuar në fabrikë. Por materiali ende kushton shumë, kështu që nuk është i përshtatshëm për asnjë objekt.
- Materialet e pajisura me veti izoluese të zërit mund të plagosen vetë. Ose një lloj izolimi i mbështjellë ose polietileni i shkumëzuar është i përshtatshëm për këtë.
Sa më e trashë të jetë shtresa e materialit, aq më pak zhurmë e jashtme do të ketë. Atëherë vetë puna do të japë rezultate më të mira.
Për izolimin e zërit, çdo blerës zgjedh materialet në mënyrë të pavarur, sipas preferencave të tij personale. Këtu janë vetëm disa që janë më të përhapurit:
- Tekstil me fije qelqi.
- Shkumë polietileni.
- Një lloj gome sintetike.
- Me bazë leshi mineral.
Çdo shtëpi është e pajisur me një vulë uji. Pajisja është pjesërisht e aftë të thithë zhurmën e jashtme.
Rreth veçorive të vulës së ujit
Valvulat mund të instalohen me një kapacitet të përbashkët për të gjitha pajisjet, ose individualisht për secilën prej tyre.
Më të përhapurit janë valvulat metalike ose plastike. Ato janë instaluar aty ku tubat lidhen me njëri-tjetrin.
Instalimi i kanalizimeve të brendshme - në video: