File adalah salah satu alat paling kuno di bumi. Anda tidak dapat melakukannya tanpanya di zaman teknologi modern ini: hampir semua pekerjaan kayu dan logam memerlukan file.
File adalah alat pemotong untuk mengolah bahan dengan metode pemotongan lapis demi lapis (filing). Tujuan pengarsipan adalah untuk membawa bagian tersebut ke bentuk dan ukuran yang diinginkan, dan untuk memberikan kekasaran permukaan yang diinginkan. File adalah batang baja dengan penampang persegi panjang, segitiga atau lainnya, yang pada permukaannya dibuat takik, membentuk gigi tajam.
Sebuah pegangan dipasang pada betis kikir yang berbentuk kerucut. Hal inilah yang sangat menentukan kenyamanan dan keamanan kerja, sehingga harus cukup awet dan tahan terhadap minyak, bensin, dan pelarut. Pegangan secara tradisional terbuat dari kayu keras dan plastik keras. Gagang kayu diperkuat dengan klip logam (cincin), yang melindungi dari perpecahan memanjang. Untuk melindunginya dari pembusukan dan kontaminasi, mereka dilapisi dengan pernis atau cat tidak berwarna.
Pegangan plastik berbentuk ergonomis dengan lubang untuk menggantung file selama penyimpanan. Dalam produksi kikir domestik, dua kelompok baja perkakas biasanya digunakan: baja perkakas U10A - U13A murni tanpa paduan dan baja kromium paduan ShX15 dan 13X, yang memungkinkan diperolehnya baja perkakas yang tinggi. alat berkualitas.
Klasifikasi file
Tergantung pada pekerjaan yang dilakukan, file dibagi menjadi file pengerjaan logam tujuan umum, pengerjaan logam untuk pekerjaan khusus, kikir mesin, kikir jarum, dan serak. File bangku untuk pekerjaan khusus dirancang untuk menghilangkan kelonggaran yang besar, untuk pengarsipan alur, permukaan berbentuk dan melengkung, untuk memproses logam non-besi, bahan non-logam. File bangku untuk pekerjaan khusus dan file mesin terutama digunakan dalam produksi. Dalam kehidupan sehari-hari, alat yang paling populer adalah file tujuan umum dan serak.
Takik pada permukaan kikir membentuk gigi yang menghilangkan serpihan dari bahan yang sedang diproses. File dengan potongan tunggal dapat menghilangkan serpihan lebar yang sama dengan panjang keseluruhan takik dan dirancang untuk menghasilkan permukaan dengan sedikit kekasaran. Mereka digunakan untuk mengarsipkan benda yang terbuat dari logam lunak dan paduan dengan ketahanan potong rendah, serta bahan non-logam.
Kikir dengan potongan ganda (silang) adalah kombinasi potongan tunggal dan potongan tambahan yang kurang dalam, dibuat miring. Titik perpotongan takik ini memecahkan chip yang dihasilkan selama proses pengarsipan. Takik ini adalah yang utama untuk file pengerjaan logam. Mereka digunakan untuk mengarsipkan bagian yang terbuat dari baja, besi cor dan lainnya bahan keras dengan ketahanan pemotongan yang tinggi.
File dengan takik serak (titik) (rasps) digunakan untuk memproses produk yang terbuat dari logam yang sangat lunak dan bahan non-logam - kulit, karet. Potongan serak diperoleh dengan menekan logam dengan pahat khusus.
File potongan busur dirancang untuk memproses logam lunak. Potongan busur diperoleh dengan penggilingan; ia memiliki rongga besar di antara gigi dan bentuk melengkung, yang menjamin produktivitas tinggi dan peningkatan kualitas permukaan mesin.
File masinis tujuan umum
Jenis berkas |
Aplikasi |
Berhidung pesek |
Untuk pengarsipan permukaan datar eksternal atau internal |
Persegi |
Untuk menggergaji lubang persegi, persegi panjang dan poligonal |
Bersegi tiga |
Untuk pengarsipan sudut tajam(60° atau lebih) seperti pada di luar bagian, dan di alur, lubang dan alur |
Berbentuk setengah lingkaran |
Untuk pemesinan permukaan melengkung cekung dengan radius signifikan dan lubang besar |
Untuk menggergaji lubang bulat atau oval dan permukaan cekung radius kecil |
|
Berbentuk belah ketupat |
Untuk pengarsipan roda gigi, cakram dan sproket |
Gergaji besi |
Untuk pengarsipan sudut dalam, alur berbentuk baji, alur sempit, bidang pada lubang segitiga, persegi dan persegi panjang |
Menurut jumlah takik (gigi) per panjang 10 mm, kikir dibagi menjadi enam kelas, dan takik memiliki nomor yang sesuai: 0, 1, 2, 3, 4, dan 5.
Kelas satu (ruangan 0 dan 1)- takik bajingan: paling kasar, memiliki jumlah gigi sedikit per 10 mm - 4-12.
Kelas dua (nomor 2 dan 3)- yang disebut kedudukan pribadi: rata-rata, jumlah gigi 10 mm lebih banyak dari kelas sebelumnya - 13-24.
Kelas tiga, empat dan lima (nomor 4 dan 5)- takik beludru: halus, jumlah gigi per 10 mm - 24-28.
Semakin kasar takiknya, semakin tinggi kecepatan pengarsipannya, namun semakin besar pula kekasaran permukaannya.
Panjang file diukur sepanjang bagian kerjanya, tidak termasuk betis. Kisaran ukuran: 100, 150, 200, 250, 300, 350 mm. Dengan bertambahnya panjang, jumlah gigi per 10 mm bilah berkurang.
Memarut adalah kikir dengan potongan langka, besar dan tajam untuk mengolah logam lunak, tulang, kulit, dan kayu. Parutan berbeda dari kikir tukang logam dengan takiknya, yang dibuat dalam bentuk gigi pendek besar berbentuk piramida. Gigi-giginya tersusun berjajar tegak lurus terhadap porosnya. Untuk mencegah lekukan saat pengarsipan, baris-baris tersebut diimbangi satu sama lain dengan setengah jarak antar gigi. Serak bisa berhidung tumpul dan berhidung lancip, serta bulat dan setengah lingkaran dengan takik nomor 1 dan 2, panjang 250, 300 atau 350 mm.
Jumlah gigi per 10 mm bilah kikir, bergantung pada panjang dan jenis takiknya
Panjang |
Takik |
||
Drachevaya |
Pribadi |
Beludru |
|
Berdasarkan materi situs
Saat ini, jangkauan aplikasi perangkat genggam tertua ini praktis tidak terbatas.
Berbagai jenis Alat ini digunakan untuk menyelesaikan bagian dan mencapai kebersihan permukaan yang dibutuhkan.
Terimakasih untuk teknologi modern, file mekanis telah dilengkapi dengan berbagai peralatan listrik dan nirkabel.
Apa itu file dan untuk apa?
Ini adalah salah satu jenis alat pengerjaan logam yang paling populer untuk pemrosesan manual berbagai macam bahan: logam, kayu, plastik, tulang, kaca dan lain-lain.
Setiap aplikasi memiliki jenis alatnya masing-masing elemen yang sesuai file untuk tugas yang ada.
Sebagai fungsi umum, ini dirancang untuk melakukan operasi berikut:
Mengasah ujung tombak;
penggilingan dan deburring;
membersihkan permukaan sampai tingkat kekasaran tertentu;
pengarsipan permukaan lapis demi lapis;
memotong bagian yang kosong;
penyesuaian ukuran;
membuat alur, talang, radius, spline, alur, dll;
memberikan elemen struktural bentuk yang diinginkan.
Permukaan bergelombang mampu memberikan tingkat akurasi dan kebersihan yang tinggi pada elemen yang diproses dengan biaya fisik yang rendah.
Kikir kuku berhak diklasifikasikan sebagai salah satu jenis alat ini.
Penampilan dan bentuk file
Secara eksternal, ini adalah balok berbilah banyak yang terdiri dari strip logam dengan gigi tajam di berbagai sudut.
Biasanya, elemen utama sebuah file adalah bilah dan betis untuk memasang pegangan.
Menurut bentuk area kerja, perkakas dapat berupa:
Berbentuk persegi panjang datar;
bulat;
berbentuk setengah lingkaran;
bulat telur;
berbentuk belah ketupat;
berbentuk segitiga sama sisi atau tumpul.
Beberapa varietas diproduksi tanpa betis, sementara jenis lainnya menggunakan perpanjangan bilah baja sebagai pegangannya.
Biasanya, panjang bilah kerja berkisar antara 100 hingga 400 mm.
Beberapa jenis, dengan mempertimbangkan spesifikasinya, diproduksi dalam ukuran besar.
Prinsip pengoperasian file adalah menghilangkan lapisan atas dari benda kerja dengan cara gesekan.
Gigi batang menentukan kualitas potongan, dan kedalamannya tergantung pada gaya yang diterapkan dengan menekan alat dan kecepatan gerakan.
Lebih kasar dan takik besar memungkinkan Anda bekerja lebih cepat, tetapi pada saat yang sama kualitas pemrosesan menurun.
Tepi halus atau berlian memberikan permukaan yang hampir sempurna.
Dalam banyak hal, hasil pekerjaan bergantung pada karakteristik bahan dan jenis file yang dipilih dengan benar.
Klasifikasi file
Klasifikasi utama file, menurut standar negara bagian Gost 23726-79, dilakukan berdasarkan jenis penggunaan dan membagi alat menjadi 5 kelompok utama:
Untuk pengerjaan logam;
tujuan khusus;
file jarum;
serak;
mesin dan pita.
Selain itu, jenis file dibedakan berdasarkan kedudukannya - mereka diberi nomor berdasarkan kelas dari 0 hingga 5.
Menandai
Penandaan mencerminkan data yang diperlukan yang mencirikan tujuan instrumen.
Ini adalah kelas dari 1 hingga 6 dan panjangnya ditandai dengan huruf Latin L.
Dan juga jenis pemotongan file yang diberi nomor 0 sampai 5.
Parameter penting seperti kekerasan gigi dilambangkan dengan singkatan HRC yang dikombinasikan dengan angka dua digit - misalnya, HRC 55.
Jenis baja juga dapat ditunjukkan, misalnya: 13X atau U13A.
Penunjukan CM diterapkan pada perkakas yang dimaksudkan untuk memproses logam non-ferrous.
Jenis takik dan penomorannya
Jenis pemotongan file adalah indikator kinerja paling penting berdasarkan sifat pengklasifikasian alat tersebut.
Lapisan abrasif dapat berupa:
1. Lajang sederhana
Potongan tipe tunggal sederhana digunakan untuk memproses logam lunak dan bahan lainnya, serta untuk produksi file khusus.
2. Ganda
Takik ini meningkatkan dampak pada permukaan benda kerja.
Jenis file ini digunakan untuk pemrosesan kasar besi cor, perunggu, dan baja.
3. Krestovy
Potongan melintang terdiri dari gigi untuk pemrosesan kasar, dan potongan halus berfungsi sebagai tambahan untuk menggiling bahan.
Hal ini memastikan pemrosesan yang lebih baik.
4. Tempat
Potongan titik atau serak terdiri dari gerinda kecil dan ideal untuk memproses kayu lunak, kulit, karet, dll.
5. Penggilingan busur
Berkat bentuknya yang istimewa, takik ini berkontribusi terhadap produktivitas tinggi dan kualitas baik produk olahan.
Ini digunakan saat bekerja dengan logam non-ferrous dan kayu.
Seperti disebutkan di atas, jenis file berbeda dalam jumlah potongan dari 0 hingga 5.
Angka 0 dan 1 dibedakan berdasarkan gigi besar dan jarang sebanyak 4 hingga 12 buah per 10 mm.
Nomor 2 dan 3 memiliki 13-24 gigi per 10 mm.
Takik No. 4 dan 5 dicirikan oleh jumlah gigi terbesar - lebih dari 24 per 10 mm.
Jenis file dan tujuannya
Jenis file berdasarkan kelas dan bentuknya menentukan ruang lingkup utama aplikasi.
Kelas 1 mencakup perkakas dengan takik bernomor 0 sampai 1.
Ini adalah file kasar, tugas utamanya adalah penyelesaian permukaan kasar.
Kelas kedua mencakup perkakas dengan bahan abrasif No. 2 dan 3.
Itu kurang berkas kasar, mereka menyebutnya pribadi, dan digunakan terutama untuk pemrosesan finishing, karena itu meninggalkan permukaan yang lebih halus.
Alat kelas 3,4,5 dan 6 mempunyai notch 4 dan 5 angka.
Mereka lebih dikenal sebagai “beludru” atau kikir perhiasan dan digunakan untuk finishing.
Jenis file berdasarkan bentuknya
Klasifikasi berdasarkan bentuk membagi ruang lingkup penerapan secara lebih rinci.
1. Datar, berhidung tumpul file adalah alat universal, karena... Mereka dirancang untuk mengerjakan logam dan kayu.
Mereka dapat dengan mudah menangani permukaan datar dan cembung. Mereka memiliki satu takik di salah satu sisi mukanya.
2. Hidung pesek dan runcing Mereka digunakan untuk memproses permukaan datar eksternal atau internal, dan juga digunakan untuk menggergaji celah dan alur.
3. Persegi Produk ini memiliki hidung yang lancip dan digunakan untuk menggergaji lubang persegi dan persegi panjang serta permukaan yang menyempit.
4. Bentuk segitiga Tersedia dalam dua versi - untuk pemotongan bahan lapis demi lapis, pemrosesan sudut bagian dalam berbagai bentuk, lubang segitiga untuk pengarsipan alur kecil dan alur berbentuk baji.
Jenis ini juga digunakan untuk mengasah gergaji kayu sehingga disebut juga gergaji besi.
5. Bentuk bulat - Tipe ini, seperti tipe segitiga, memiliki dua subtipe berbeda.
Untuk mengolah alur bulat, lubang, penggergajian lapis demi lapis dan untuk mengasah gergaji kayu dan rantai gergaji.
Jenisnya mengklasifikasikan alat ini sebagai alat universal, karena menggabungkan keunggulan file datar dan bulat.
Idealnya melakukan pemrosesan permukaan bulat dan datar, memiliki hidung runcing.
7. Bentuk berlian memungkinkan Anda memproses material dengan konfigurasi permukaan kompleks secara efektif, termasuk bekerja dengan roda gigi, sproket, roda, dan cakram.
File yang ditujukan untuk operasi khusus disebut alat tujuan khusus, ini termasuk pelapis berlian dan permukaan pemotongan lainnya dengan kekerasan lebih tinggi yang ditujukan untuk paduan non-besi, logam, ubin atau keramik dan bahan lainnya.
Jenis dan ukuran takik
Sifat takik menentukan jenis file utama.
Profil dan ukuran gigi kikir bergantung pada mesin yang digunakan untuk mengaplikasikan permukaan pemotongan.
Biasanya digunakan untuk produksi:
— mesin pemotong gergaji dengan pahat;
— Mesin penggiling;
— mesin penggiling dengan lingkaran khusus;
— mesin pemotong dan penggerek gigi.
Terlepas dari metode produksinya, semua gigi memiliki parameter tertentu untuk sudut lokasi, penajaman dan pemotongan.
Semakin banyak takik per 1 cm area kerja, semakin kecil takik gigi.
Rasio tinggi terhadap tinggi takik utama harus minimal 0,5.
Bahan berkas
Menurut standar Rusia dan internasional, file dibuat dari baja perkakas karbon.
Ini termasuk merek yang paling umum:
- kamu 10,12, 13;
— Pada 10, 12, 13 A;
— ShKh15 UA;
— 13X dan analog asingnya.
Apa itu kikir jarum dan tujuannya?
Produk berukuran kecil, yang tujuan utamanya adalah ukiran, pola dan perhiasan; Mereka juga digunakan untuk menggiling tempat-tempat yang sulit dijangkau; bagian pendek dari profil, sudut atau lubang; untuk keramik, paduan keras, finishing alat pemotong - disebut file jarum.
File bangku dan file jarum tersedia dalam berbagai bentuk.
Menurut jenis takik, yang terakhir diproduksi dengan angka 1 hingga 5 dan, tergantung pada jenisnya, memiliki 20 hingga 112 gigi.
Produksi kikir jarum diatur oleh Gost 1513-67.
Menurut standar, panjang produk bisa 80, 120 dan 160 mm.
Potongan abrasif tidak terletak seluruhnya permukaan kerja, dan dengan panjang 40, 60 dan 80 mm. Area kerja utama ditutup dengan potongan melintang, dan sisi sempit ditutup dengan potongan tunggal.
Apa itu senapan dan untuk apa?
Salah satu jenis kikir jarum adalah alat khusus yang disebut riffle.
Ini memiliki area kerja melengkung dan terbuat dari paduan magnetik.
Cakupan penggunaan riffle cukup sempit - ini adalah pekerjaan perhiasan, dimana alat tersebut digunakan untuk memisahkan cara kerja riffle dari serbuk gergaji paduan berharga.
Serak dirancang untuk memproses logam lunak, karet, kulit, kayu, tulang dan bahan serupa.
Menurut Gost, ada tiga jenis alat utama:
- tujuan umum;
- pembuat sepatu (sepatu)
- hewan berkuku.
Serak serba guna tersedia dengan hidung lancip dan tumpul, tipe datar, atau bulat dan setengah lingkaran dengan takik 1 dan 2.
Ciri khas spesies ini adalah ukuran besar gigi dan lekukan yang luas di depan setiap gigi.
Apa itu file yang dikalibrasi
File yang dikalibrasi berfungsi sebagai semacam standar untuk menentukan kekerasan yang dikeraskan, bagian logam, benda kerja menurut skala Vickers atau skala Rockwell “C”.
Penguji kekerasan memungkinkan Anda dengan cepat dan murah menentukan sifat suatu material dalam kehidupan sehari-hari dan industri, serta di tempat-tempat yang sulit dijangkau yang tidak memungkinkan untuk menggunakan alat stasioner atau portabel.
Untuk tujuan ini, set diproduksi di mana perkakas, tergantung pada standar kekerasannya, berbeda warnanya:
1. HRC65 Hitam
2. HRC Biru 60
3. HRC 55 berwarna hijau tua
4. HRC 50 hijau muda
5. HRC Kuning 45
6. HRC Merah 40
Bekas goresan pada produk kontrol menunjukkan bahwa permukaan yang diuji lebih lunak dibandingkan determinan.
Pengujian dilakukan sampai kekerasan benda lebih tinggi dari kekerasan alat penguji dan berada di antara nilai rata-rata kedua instrumen.
Jenis file apa yang ada?
Produksi modern tidak selalu bisa puas dengan hasil kerja manual, sehingga produsen menawarkan alat seperti kikir listrik atau pneumatik.
Yang terakhir ini dicirikan oleh produktivitas yang rendah, tetapi unggul dalam hal bobot dan ukuran.
Peralatan jaringan memiliki kinerja tinggi, lebih berat dan lebih besar dari yang pertama, tetapi tidak memerlukan pasokan udara tambahan.
Dengan berkembangnya teknologi otonom, jenis baru– file tape tanpa kabel yang memungkinkan Anda bekerja tanpa terikat pada power point.
Meskipun pneumatik secara bertahap mulai dikeluarkan dari rak-rak toko, ada model yang paling memenuhi kebutuhan konsumen.
Salah satu opsi yang populer adalah file pita pneumatik.
Ini melakukan pekerjaan pembersihan yang bagus permukaan logam dari bekas pengelasan, korosi dan lain-lain di perusahaan pengerjaan logam kecil, bengkel mobil swasta, bengkel produksi dan perakitan.
Cara memilih file
Saat memilih jenis kikir tangan tertentu, para profesional merekomendasikan untuk memperhatikan bahan yang diproses dan karakteristik kinerjanya.
Salah satu parameter penting adalah kualitas gigi.
Efisiensi kerja secara langsung bergantung padanya.
Selain itu, perlu dipertimbangkan:
— Jenis takik;
— Bentuk fluida kerja;
- Panjang;
— Fitur pegangan atau betis.
Dimensinya harus sesuai dengan dimensi bagian yang sedang diproses.
Untuk bagian besar, gunakan panjang maksimum - dari 22 hingga 350 mm, dan untuk bagian kecil - dari 150 hingga 180 mm.
Pegangannya harus dapat diandalkan dan nyaman.
Gagang kayu dianggap kurang dapat diandalkan, plastik dan karet lebih nyaman.
Selain itu, perkakas sering kali ditawarkan tanpa pegangan.
Indikator seperti distribusi kekerasan dan viskositas sangat penting.
Viskositasnya minimum di permukaan dan maksimum di kedalaman, sedangkan kekerasannya sebaliknya.
Kekerasan yang tidak memadai menyebabkan hilangnya ketajaman gigi dengan cepat, dan viskositas yang rendah mengancam rusaknya takik selama pengoperasian.
Kekerasan permukaan diatur tergantung tujuannya.
Angka rata-rata untuk produsen adalah nilai berikut untuk berbagai jenis file:
1. Keperluan pertukangan dan pengerjaan logam – dari 64 hingga 66 HRc;
2. Jenis penggilingan – dari 65 hingga 67 HRc;
3. Serak – dari 53 hingga 56 HRc.
Kualitas sebenarnya hanya diverifikasi saat digunakan.
Produsen file
Memang, menilai kualitas suatu alat secara visual bagi non-profesional adalah tugas yang sangat sulit.
Oleh karena itu, kriteria utamanya adalah ulasan pengguna dan reputasi pabrikan.
Di antara merek paling populer yang patut disoroti:
- Banteng;
- Husqvarna;
- antar alat;
- Metabo;
- Makita;
- Pandai besi;
- Vira;
- orang tabah;
- Menguasai;
- Matriks;
- saudara teknologi;
- Mega;
- tetap;
- puncak;
- Bosch dkk.
Setiap produsen patut mendapat perhatian khusus, sehingga situs web kami memiliki bagian terpisah yang menyediakan informasi tentang berbagai perusahaan, merek, merek, dll.
Mengajukan - alat pemotong untuk mengolah bahan dengan cara pemotongan lapis demi lapis (filing). Ini adalah strip baja (bilah), pada permukaan kerja yang dibuat "takik" - elemen pemotong (gigi tajam). Sebuah pegangan dipasang pada betis kikir yang berbentuk kerucut. Menurut tujuan yang dimaksudkan, file adalah:
- Tukang kunci (berbagai bagian) - dirancang untuk pengarsipan bagian secara presisi ke ukuran tertentu, menghilangkan talang dan gerinda.
- Mengasah (bagian bulat) - hanya digunakan untuk mengasah rantai gergaji bensin dan listrik.
Penampang file:
Beras. 1. File dari berbagai bagian:
a - datar (persegi panjang); b - persegi; c - segitiga; tanah; d - setengah lingkaran
datar - penampang persegi panjang, dirancang untuk pengarsipan permukaan lebar. Ujungnya mungkin meruncing (jari kaki). Terdapat lekukan pada tepi samping, biasanya hanya pada satu sisi;
persegi, segitiga, bulat file digunakan untuk memproses lubang dan alur; jari kaki mereka selalu meruncing;
berbentuk setengah lingkaran menggabungkan kemampuan file datar dan bulat.
Jenis takik:
Beras. 2. Jenis bentukan file utama:
Tunggal; b - ganda; di - oberg
- lajang - diterapkan pada sudut 70° terhadap sumbu memanjang file, terkadang pada 45°. Ini menghilangkan serpihan lebar dari bahan yang sedang diproses dan dirancang untuk menghasilkan permukaan dengan sedikit kekasaran;
- dobel (menyeberang) - merupakan kombinasi takik tunggal dan takik bantu yang kurang dalam, dibuat miring terhadap takik tunggal. Titik perpotongan takik ini memecahkan chip yang dihasilkan selama proses pengarsipan. Takik ini adalah yang utama untuk berkas pekerja logam;
- dobel (“oberg”) - dengan takik tambahan yang lebih jarang (2-3 kali). Menempati posisi perantara antara takik tunggal dan ganda dalam hal efisiensi dan kebersihan perawatan permukaan.
Ukuran takik- ini adalah jumlah gigi per 1 cm panjang bilah kikir Berdasarkan jumlah gigi, dibedakan tiga ukuran takik:
- garang - yang paling kasar, memiliki jumlah gigi yang sedikit per 1 cm;
- pribadi - sedang, jumlah gigi lebih banyak 1 cm dari sebelumnya;
- beludru - kecil, jumlah gigi terbanyak per 1 cm.
Semakin kasar takiknya, semakin tinggi kecepatan pengarsipannya, namun semakin besar pula kekasaran permukaannya.
Masa pakai perkakas tergantung pada kualitas baja, kualitas pemotongan, dan perlakuan panas.
Untuk produksi file dalam negeri Dua kelompok baja perkakas yang digunakan:
- dibatalkan ditingkatkan U10A - U13A;
- paduan baja kromium ШХ15 dan 13Х, memungkinkan diperolehnya perkakas berkualitas tinggi dengan kekerasan permukaan dari 64 hingga 66 HRc.
Beras. 3. Pegangan file:
a - kayu dengan bingkai logam; b - plastik
Untuk pembuatannya gunakan:
kayu keras . Pegangan seperti itu diperkuat dengan klip logam (cincin), yang melindunginya dari perpecahan memanjang. Untuk melindunginya dari pembusukan dan kontaminasi, mereka dilapisi dengan pernis atau cat tidak berwarna;
plastik - keras dan tahan lama untuk badan tempat file shank dipasang, dan elastis untuk sisipan yang memberikan pegangan yang nyaman. Paling sering, pegangan ini memiliki bentuk ergonomis dengan lubang untuk menggantung file selama penyimpanan.
Pegangan yang dipilih sesuai dengan ukuran kikir dipasang pada betisnya, yang harus sesuai dengan kedalaman 2/3 hingga 3/4 panjangnya. Panjang pegangannya harus satu setengah kali lebih panjang dari betis kikir.
Saat memasukkan, betis kikir dimasukkan ke dalam lubang pegangan dan dengan tangan kanan, dengan menggunakan pukulan vertikal, kepala pegangan dipukul ke meja kerja. Anda juga dapat melakukan ini: masukkan tangkai kikir ke dalam lubang pada pegangannya dan, ambil kikir tersebut tangan kiri, berikan beberapa pukulan ringan ke kepala pegangan dengan palu. Untuk melepaskan pegangan dari kikir, ambil dengan tangan kiri Anda dan lakukan dua atau tiga pukulan pendek dan lemah dengan tangan kanan Anda dengan palu di tepi atas. dekat ring. File kemudian dengan mudah keluar dari lubang
Memilih file, Anda perlu memperhatikan apa yang harus mereka miliki:
takik yang jelas, tanpa cacat apa pun;
seragam warna abu-abu seluruh permukaan, tanpa goresan (menunjukkan pelanggaran kondisi perlakuan panas), bekas karat, minyak dan kontaminan lainnya;
Mengajukan – Ini alat tangan, dimaksudkan untuk pemrosesan logam. Dapat juga digunakan untuk bahan keras lainnya, seperti plastik, textolite, dll. Menggunakan file memungkinkan Anda menggiling ketidakteraturan atau menyesuaikan produk ke parameter yang diperlukan, memperluas diameternya atau memperpendeknya. Itu terbuat dari baja perkakas keras, membuatnya lebih keras daripada kebanyakan logam yang diprosesnya.
Fitur dan tipe desain
Alatnya berupa strip baja dengan lekukan, yang diikatkan pada gagang kayu atau plastik. Takik file tersedia dalam berbagai ukuran, yang sesuai dengan angka tertentu dari 0 hingga 5. Takik terbesar adalah No. 0, dan yang terkecil adalah No. 5. Menurut klasifikasi nomornya, file adalah:
- Drachevye(No. 0-1 hingga 12 takik per 1 cm permukaan) - memiliki gigi besar yang memungkinkan Anda menggores lapisan karat tebal, memisahkannya dari logam bersih.
- Pribadi dan semi pribadi(No. 2-3 dari 13 hingga 44 takik per 1 cm permukaan) - digunakan untuk memproses logam apa pun, menghilangkan ketebalan berlebih.
- Beludru(No. 4-5 dari 45 hingga 80 takik per 1 cm permukaan) - digunakan untuk finishing, untuk mencapai kehalusan maksimum benda kerja.
Semakin besar giginya, semakin banyak logam yang bisa dihilangkan. Saat memproses dengan takik yang tinggi dan jarang, permukaan benda kerja ditutupi dengan alur yang dalam, jadi untuk kenyamanan pemrosesan, Anda harus memulai dengan jumlah file yang lebih kecil dan secara bertahap beralih ke takik yang sangat halus, yang diperlukan untuk mencapai kehalusan maksimal. permukaan, jika perlu.
Perlu dipertimbangkan bahwa file dengan takik yang sangat halus dengan cepat tersumbat oleh serutan yang dihilangkan, dan oleh karena itu memerlukan pembersihan berkala, karena jika tidak, penghilangan lapisan logam akan berhenti. Selain itu, perlu diperhatikan bahwa kecepatan pengerjaan dengan alat jenis beludru puluhan kali lebih rendah dibandingkan dengan jenis hiasan.
Jenis takik
File ini berbeda tidak hanya dalam ukuran gigi takik, tetapi juga dalam fitur penerapannya:
- Lajang.
- Menyeberang.
- Dugovaya.
- Memarut.
- Dicap.
Sederhana atau lajang Takik dapat digunakan untuk memproses logam non-besi. Ini dengan cepat menghilangkan lapisan benda kerja dan dibersihkan dengan baik dari keripik. Saat bekerja, alat seperti itu banyak bergetar, yang menyebabkan tangan cepat lelah. Perlu dicatat bahwa kekhasan sudut kemiringan gigi tidak memungkinkan pemrosesan logam keras. Takik itu sendiri diterapkan pada sudut 25-30 derajat.
Menyeberang Potongannya cocok untuk pengerjaan baja, besi cor, dan perunggu. Geriginya berpotongan membentuk berlian. Sudut kemiringan takik utama adalah 25 derajat, dan takik bantu adalah 45 derajat. Jenis kikir ini cukup cepat tersumbat oleh serutan, sehingga tidak cocok untuk logam lunak. Untuk memastikan pekerjaan yang produktif dan nyaman, penting untuk menjaga keberadaan sikat logam, yang harus digunakan untuk menyikat serpihan di sela-sela gigi bilah perkakas secara berkala.
Tipe busur Takik ini cocok untuk mengerjakan logam non-besi, serta kayu keras seperti beech, oak, dll. Setelah pengarsipan seperti itu, goresan yang cukup rapi tertinggal pada benda kerja, yang dapat dengan mudah diampelas.
Serak atau titik Takik ini terutama digunakan untuk menghilangkan kerak atau endapan karat pada logam besi dengan cepat. Ini sangat efektif untuk pengolahan kayu kasar.
Dicap Takik digunakan untuk tujuan yang sama seperti serak. Keunikannya terletak pada giginya yang bersudut, yang mencengkeram benda kerja seperti kait, menghilangkan ketebalannya. Saat bekerja, alur kasar terbentuk. Gigi cepat aus, jadi lebih baik tidak menggunakan alat seperti itu logam keras. Ini sangat cocok dengan kayu. Saat memproses aluminium, bilahnya dengan cepat tersumbat oleh serpihan, yang sulit dihilangkan.
Varietas bentuk
Adapun bentuk-bentuk filenya adalah:
- Datar.
- Persegi.
- Bulat.
- Berbentuk setengah lingkaran.
- Segitiga.
Datar file cocok untuk memproses benda kerja besar dengan area pelepasan yang besar. Mereka dibebaskan ukuran yang berbeda dan, biasanya, memiliki lekukan di kedua sisi, yang memungkinkan Anda membalikkan alat dan terus bekerja saat mengemudikan salah satunya.
Persegi file tersebut memiliki potongan di keempat sisinya. Hal ini memungkinkan pemrosesan sudut siku-siku dalam dua bidang. Dengan bantuan mereka, Anda dapat menghilangkan lapisan berlebih. Alat ini tersedia dengan kekerasan gigi yang berbeda-beda. Ada kikir persegi dengan panjang hingga 50 cm, yang memungkinkan pengupasan logam dipercepat.
Bulat file adalah solusi yang bagus untuk menyiapkan lubang yang bulat atau bulat sempurna. Dengan bantuannya, Anda dapat meningkatkan diameter bagian dalam dengan menyesuaikannya dengan parameter yang diperlukan.
Tipe setengah lingkaran digunakan dalam kasus di mana perlu untuk memproses permukaan bulat. Lebar file semacam itu lebih besar daripada file bulat sempurna, yang menghilangkan kemungkinan pendalaman permukaan yang berlebihan pada satu titik, sehingga melanggar geometri yang diperlukan.
Bersegi tiga File ini digunakan untuk mengarsipkan sudut tidak siku-siku internal. Semua tepi alat memiliki takik, seringkali berbeda tinggi atau sudut penerapannya, yang menjadikan alat tersebut universal. Tipe segitiga juga cocok untuk permukaan datar. Pada saat yang sama, bekerja dengannya kurang nyaman dibandingkan dengan file lurus karena area kerja takik yang kecil.
Bagaimana menjaga file dalam kondisi kerja
Agar file tetap dalam kondisi kerja selama mungkin, file harus dibersihkan setiap kali selesai digunakan. Untuk melakukan ini, gunakan sikat logam. Jika Anda meninggalkan serpihan di ceruk bilahnya, lama kelamaan serpihan tersebut akan menempel erat di bawah pengaruh korosi atau oksidasi, sehingga akan jauh lebih sulit untuk menghilangkannya.
Jangan merawat permukaan yang kotor atau basah. Kikir terbuat dari baja perkakas keras yang rentan terhadap karat. Ketika tanda-tanda korosi muncul, bilah mulai kurang efektif menempel pada logam benda kerja, sehingga mempersulit pekerjaan. Dianjurkan juga untuk menghindari permukaan yang mengandung gemuk atau oli mesin. Lemak yang terperangkap pada takik akan menyebabkan debu menempel, sehingga juga menurunkan produktivitas pengamplasan.
Mengasah file dengan asam sitrat
Seiring waktu, bahkan perkakas baja padat dengan kualitas terbaik pun secara bertahap kehilangan ketajamannya, sehingga menjadi tidak dapat digunakan. Kikir tidak bisa diasah seperti pisau, pahat atau pahat, sehingga banyak orang membuangnya begitu saja ke tempat sampah atau mengasahnya menjadi pahat. Faktanya, file pun dapat diasah tanpa usaha apa pun. Yang dibutuhkan hanyalah asam sitrat.
Pertama, alat harus dibersihkan dari serpihan yang tersumbat dengan menggunakan sikat logam. Setelah itu, kain harus dicuci deterjen untuk mencuci piring atau membersihkan kompor. Hal ini diperlukan untuk menghilangkan sisa kotoran dan minyak. Untuk efek maksimal, Anda dapat menggunakan sikat gigi untuk menyikat setiap milimeter instrumen. Setelah itu, Anda perlu menyiapkan larutan asam sitrat, untuk ini Anda perlu mengambil wadah vertikal berisi air. Bisa jadi botol plastik atau toples kaca, cocok untuk tinggi badan. Itu harus dituangkan ke dalamnya dan dilarutkan asam sitrat. Semakin kuat solusinya, semakin cepat efeknya, tetapi jangan gunakan seluruh kemasan sekaligus - itu akan berlebihan!
Bagian kerja dari file harus benar-benar terendam dalam larutan asam, sehingga seluruh bilah dengan takik tertutup. Pegangannya harus tetap berada di luar. Durasi pemasukan instrumen ke dalam larutan tergantung pada konsentrasi dan baja dari mana bilah dibuat. Setiap beberapa jam Anda perlu menghapus file dan mengevaluasi ketajamannya. Untuk melakukan ini, Anda bisa menggunakan persiapan rendah lemak apa pun. Setelah setiap pengujian, instrumen harus dibersihkan dengan sikat untuk menghilangkan serbuk gergaji. Pada saat yang sama, penting untuk mencoba untuk tidak menyentuh kanvas dengan tangan Anda, karena meninggalkannya di atasnya bintik-bintik berminyak dari jari Anda, Anda dapat mengisolasi bagian logam dari reaksi kimia dengan asam.
Durasi penggoresan mata pisau untuk diasah dapat memakan waktu beberapa jam hingga satu hari jika larutannya sangat lemah dan kualitas bajanya sangat tinggi. Dimungkinkan juga untuk menggunakan asam lain yang termasuk dalam komposisinya reaksi kimia dengan logam hitam. Perlu diingat bahwa larutan yang lebih kuat mengeluarkan uap berbahaya yang sebaiknya tidak dihirup.
Tujuan utama file adalah pemrosesan material secara manual. File juga digunakan untuk mengerjakan berbagai mesin pengarsipan, misalnya untuk menyelesaikan lubang chip pada cetakan bulat, pengarsipan bola untuk bantalan, pemrosesan cetakan, templat, dll.
Tujuan
File ini dirancang untuk menghilangkan lapisan logam, yang ketebalannya (0,01-1,0 mm) bertambah seiring dengan ukuran gigi.
Jenis file
Menurut Gost 1465-59, file logam tujuan umum dibagi menjadi beberapa jenis berikut:
- datar, berhidung tumpul;
- hidung runcing rata;
- persegi;
- segitiga;
- bulat;
- berbentuk setengah lingkaran;
- berbentuk belah ketupat;
- gergaji besi.
Selain file pengerjaan logam, sejumlah besar file khusus digunakan dalam praktik.
Untuk mengasah gergaji secara manual pada kayu, menurut GOST 6476-53, file khusus digunakan: a) file berhidung lancip berbentuk segitiga; b) berhidung tumpul berbentuk segitiga; c) belah ketupat; d) bulat; d) datar. Berbeda dengan kikir pengerjaan logam, kikir untuk mengasah gergaji (segitiga, belah ketupat, pipih) dilengkapi dengan bagian yang membulat.
Untuk menentukan kekerasan logam, file yang dikalibrasi digunakan.
File khusus
Sekelompok besar file khusus adalah file pelurus, yang dimaksudkan untuk mengarsipkan badan mobil sebelum didempul dan dicat. File pelurusan diproduksi berbagai bentuk datar dan melengkung.
File khusus digunakan untuk berbagai jenis file tipis dan pekerjaan finishing, misalnya, file ukiran, dll. File serak dan jarum mewakili kelompok file tangan yang agak terpisah. Hashpils, yang dibedakan dari bentuk takiknya yang unik, digunakan untuk pemrosesan bahan lembut(kayu, kulit, dll). Fitur khas kikir jarum dipotong halus dan kecil ukuran(lihat Gost 1513-53).
Dari file mesin, yang patut diperhatikan adalah file persegi yang digunakan pada mesin pengarsipan. Pengarsipan terjadi selama gerakan bolak-balik bujursangkar dari sebuah file, yang dipasang pada ujungnya di bingkai mesin.
Untuk mesin pengarsipan dengan alat berputar, digunakan file berputar (rotary), yang dibedakan berdasarkan berbagai macam bentuk. Mereka diproduksi dengan gigi potong dan giling.
ukuran
Panjang nominal file ditentukan oleh panjang bagian kerja, yaitu tanpa memperhitungkan panjang betis. File diproduksi dengan panjang 100 hingga 400 mm.
Bentuk bagian distandarisasi dan nama jenis file ditetapkan berdasarkan bagian tersebut. Selain bentuk bagian standar, bentuk bagian khusus juga digunakan tergantung pada tujuan file. Mereka sangat beragam.
Dimensi bagian (lebar, tebal, diameter, dll.) diatur tergantung pada bentuk bagian dan panjang file.
Sebagian besar jenis file standar dibuat dengan ujung yang lebih tipis baik lebar maupun tebalnya. Bentuk ini membantu mendapatkan permukaan yang sedikit cembung di sepanjang ujung file yang diperpanjang. Jari kaki dapat dianggap sebagai pagar, yang giginya secara bertahap masuk ke dalam bahan yang sedang diproses. Hal ini mengurangi jumlah gigi yang digunakan pada satu waktu, serta tenaga yang diperlukan untuk menghilangkan logam. Dengan permukaan cembung, syarat untuk mendapatkan bidang yang benar lebih mudah, karena pengarsipan hanya dilakukan pada bagian tengahnya, sedangkan bagian tepinya tidak tersentuh.
Pabrik penggergajian diperbolehkan memproduksi file dengan penampang yang sama sepanjang keseluruhannya dalam persentase kecil. Mereka dimaksudkan untuk pekerjaan seperti pengarsipan kasar, deburring, chamfering, dll. Dalam praktiknya, hanya file datar dan berhidung tumpul yang digunakan.
File dipasang pada dudukan kayu dengan betisnya, dibuat dalam bentuk batang yang meruncing secara bertahap. Panjangnya, tergantung pada panjang bagian kerja dan diatur dalam 40-100 mm, diasumsikan sama untuk semua jenis file. Shank harus diposisikan secara simetris terhadap sumbu file. Kadang-kadang pemegang khusus digunakan, di mana file ditempatkan dan disekrup dengan dua sekrup. File tersebut dilengkapi dengan dua lubang, bukan betis.
Elemen struktural file
Gigi kikir bekerja dalam kondisi sempit karena adanya pengisian rongga sela-sela gigi dengan serutan. Pelepasan akhir rongga dari keping hanya dimungkinkan setelah kikir meninggalkan kontak dengan bahan yang sedang diproses, dan hanya jika keping tidak ditekan ke dalam rongga. Dimensi rongga harus sesuai dengan jumlah chip tertentu, jika tidak, pekerjaan file akan sulit. Selama pengoperasian, rongga sering kali tersumbat oleh serpihan terkompresi, yang harus dihilangkan dengan pembersihan khusus.
Gigi kikirnya kecil dan tipis. Bagian atasnya sobek dan ada gerinda. Bentuk ini berkontribusi terhadap menumpulkannya gigi, akibatnya ruang untuk penempatan chip berkurang dan dengan demikian memperburuk kondisi untuk menghilangkan chip.
Teknologi proses pemotongan gigi kikir tidak dapat memberikan sudut rake yang optimal. Hal ini juga mempengaruhi kinerja file.
Sifat pemotongan suatu file bergantung pada pengaruh kompleks elemen struktural utamanya, yang patut mendapat perhatian berikut ini:
- jenis takik;
- jumlah dan tinggi takik;
- sudut pemotongan;
- bentuk dan tinggi gigi.
Gambar 38 - Jenis pemotongan file
Jenis takik
Dalam praktiknya, ada file dengan takik tunggal (Gambar, a) atau ganda (silang) (Gambar, b). Dengan satu potongan, gigi terletak miring terhadap sumbu kikir. Hal ini memastikan gigi secara bertahap bersentuhan dengan permukaan yang sedang diproses dan memudahkan pemotongan. Potongan tunggal hanya digunakan untuk memproses bahan lunak (terutama non-logam), serta untuk menggergaji kayu. Dalam kasus terakhir, lapisan logam yang sangat kecil harus dihilangkan untuk menghindari getaran yang kuat pada gigi gergaji yang diasah. File bangku dilengkapi dengan satu takik di salah satu sisinya yang sempit. Sisi sempit lainnya biasanya dibiarkan tanpa lekukan, yang memberikan kemudahan tertentu saat mengarsipkan bidang yang terletak tegak lurus satu sama lain.
Untuk memproses logam besi dan non-besi, digunakan file potong ganda. Ketahanan pemotongan bahan-bahan ini lebih besar, sehingga sangat sulit untuk menghilangkan serpihan lebar dengan satu kikir. Takik ganda memastikan bahwa chip lebar dibagi menjadi beberapa chip kecil, sehingga pekerjaan menjadi lebih mudah. Saat membuat file, pertama-tama takik bawah atau bantu dipotong, lalu takik atas atau utama. Takik bawah sebagian dilapisi logam dan berfungsi sebagai semacam kanvas atau jaring utama untuk takik atas, yang selalu bebas dan membentuk elemen pemotong gigi. File potong ganda lebih baik dalam menghilangkan material, karena gigi tajam yang terbentuk saat memotong kedudukan tertinggi menembus lebih dalam ke permukaan yang sedang diproses dibandingkan dengan gigi yang lebih panjang dengan potongan tunggal. Selain itu, berkat pembagian chip yang lebar menjadi yang kecil, chip tersebut tidak tersangkut di rongga sela-sela gigi dan mudah rontok.
Kedudukan bawah dan atas
Takik bawah (Gbr. 38, a) selalu mengarah ke bawah dari kiri, dan takik atas (Gbr. 38, b) selalu mengarah ke atas dari kiri. Arah pemotongan mempunyai pengaruh yang besar terhadap kemampuan pemotongan file.
Dengan sekali potong, gigi terletak pada sudut 20° tegak lurus terhadap sumbu kikir. Kikir untuk mengasah gergaji kayu dilengkapi dengan takik tunggal dengan sudut 30° tegak lurus terhadap sumbu kikir. Menurut GOST 6476-53, diperbolehkan membuat file-file ini dengan takik ganda. Dalam hal ini, kedua takik diarahkan pada sudut 30°.
Menurut GOST 1465-59, sudut kemiringan takik berikut relatif terhadap sumbu file ditetapkan untuk file tukang logam universal: untuk bagian bawah ω = 45° dan untuk bagian atas λ = 25°, dengan deviasi plus atau dikurangi 2°.